File:Bora5-small.jpg
Size of this preview: 800 × 503 pixels. Other resolutions: 320 × 201 pixels | 1,200 × 754 pixels.
Original file (1,200 × 754 pixels, file size: 607 KB, MIME type: image/jpeg)
File history
Click on a date/time to view the file as it appeared at that time.
Date/Time | Thumbnail | Dimensions | User | Comment | |
---|---|---|---|---|---|
current | 10:40, 16 July 2013 | 1,200 × 754 (607 KB) | DevWikiAdmin (talk | contribs) |
- You cannot overwrite this file.
File usage
The following 69 pages link to this file:
- AN-BMSC-001: Running Wind River VxWorks 6.9 on Bora
- Additional UART with PMOD (Bora)
- Advanced use of Yocto build system (BELK/BXELK)
- BELK-AN-001: Asymmetric Multiprocessing (AMP) on Bora – Linux FreeRTOS
- BELK-AN-002: Trace on the Bora AMP (Linux + FreeRTOS) system
- BELK-AN-003: Interfacing DDR3 SDRAM to PL
- BELK-AN-004: Interfacing BoraEVB/BoraXEVB to TFT LCD display
- BELK-AN-005: Interfacing BoraEVB to thin film electroluminescent display
- BELK-AN-006: Enabling dual Gigabit Ethernet support on BoraEVB/BoraXEVB
- BELK-AN-007: Asymmetric Multiprocessing (AMP) on Bora/BoraX with OpenAMP
- BELK-AN-008: Programming the FPGA Bitstream with U-Boot
- BELK-AN-009: Using Visual Studio Code for remote debugging
- BELK-AN-010: NAND performances
- BELK-TN-001: Real-timeness, system integrity and TrustZone® technology on AMP configuration
- BELK-TN-003: Video processing and hardware/software partitioning
- BELK-TN-004: Managing both Ethernet ports with U-Boot (BoraEVB/BoraXEVB)
- BELK-TN-005: Running PYNQ on Bora
- BELK-TN-006: Using PetaLinux to Build BELK/BXELK Software Components
- BELK-TN-008: Integrating Visual Studio Code and Lauterbach PowerView TRACE32
- BELK-TN-009: Integrating Visual Studio Code with a cross-toolchain
- BELK-TN-010: MAC address programming on OTP
- BELK-TN-011: Lock OTP Areas
- BELK-TN-012: Using XADC signal module
- BELK-TN-013: Managing ethernet and USB physical transceivers reset
- BELK-WP-001: Xilinx Zynq-7000 Errata management
- BELK/BXELK Quick Start Guide
- BELK/BXELK software components
- BORA SOM/BORA Evaluation Kit/Getting started/Kit Contents
- BORA SOM/BORA Evaluation Kit/Getting started/Unboxing
- BORA SOM/BORA Evaluation Kit/pdf
- Booting Linux Kernel
- Booting the system via NFS (BELK/BXELK)
- BoraEVB
- Bora Embedded Linux Kit (BELK)
- Build system (BELK/BXELK)
- Building Linux kernel (BELK/BXELK)
- Building U-Boot (BELK/BXELK)
- Building the Yocto BSP (BELK/BXELK)
- Carrier board design guidelines (SOM)
- ConfigID management (BELK/BXELK)
- Creating and building example Vivado project (BELK/BXELK)
- Development Kits Identification Codes
- FAQs (Bora/BoraX/BoraLite)
- Hardware Manual (Bora)
- Host setup and development flow (BELK/BXELK)
- How to configure the network interfaces
- Integration guide (Bora/BoraX/BoraLite)
- Introduction to development environment (BELK/BXELK)
- Logical structure of Bora and BoraX Embedded Linux Kits (BELK/BXELK)
- Main Page
- Mechanicals (Bora)
- PL initialization signals (Bora/BoraX/BoraLite)
- Physical devices mapping (BELK/BXELK)
- Power (Bora/BoraLite)
- Power consumption (Bora)
- Processing system peripherals (Bora)
- Processor and memory subsystem (Bora)
- Product serial number
- Programmable logic (Bora)
- RTC (Bora/BoraLite)
- Reset scheme (Bora/BoraLite)
- Restoring U-Boot on SPI NOR flash (BELK/BXELK)
- Standalone boot (BELK/BXELK)
- System boot and recovery via microSD card (BELK/BXELK)
- Thermal IC (Bora)
- Thermal management guidelines
- Watchdog (Bora)
- Template:Applies To Bora
- Category:Bora