BELK/BXELK software components

Info Box Applies to Bora Applies to BORA Xpress

Introduction

From the software standpoint, Bora Embedded Linux Kit (BELK) and BoraX Embedded Linux Kit (BXELK) are built on top of Zynq Linux BSP released by Xilinx. Customization are added to support for the Bora and BoraX platforms, in particular at bootloader and Linux kernel levels. BELK and BXELK share the same software modules, even if they are based on different hardware platforms.

The logical structure of the kits is explained here.

Kits' composition

The following table details the software modules of BELK/BXELK releases.

Kit composition
Release number BELK BXELK	1.0.0 n/a	1.1.0 n/a	2.0.0 n/a	2.1.0 n/a	2.2.0 n/a	3.0.0 n/a	3.0.1 1.0.0
Status BELK BXELK	Released n/a	Released n/a	Released n/a	Released n/a	Released n/a	Released n/a	Released Beta
Release date BELK BXELK	July 2013 n/a	November 2013 n/a	May 2014 n/a	August 2014 n/a	September 2015 n/a	March 2016 n/a	December 2016 December 2016
Release notes BELK BXELK	Ver 1.0.0	Ver 1.1.0	Ver 2.0.0	Ver 2.1.0	Ver 2.2.0	Ver 3.0.0
SOM PCB version BELK BXELK	CS020313A n/a	CS020313A n/a	CS020313B n/a	CS020313B n/a	CS020313B n/a	CS020313C n/a	CS020313C CS112714B
Supported carrier boards BELK BXELK	BoraEVB-Lite n/a	BoraEVB-Lite n/a	BoraEVB n/a	BoraEVB n/a	BoraEVB n/a	BoraEVB n/a	BoraEVB BoraXEVB
U-Boot version	2013.04-belk-1.0.0	2013.04-belk-1.1.0	2013.04-belk-2.0.0	2013.04-belk-2.1.0	2014.07-belk-2.2.0	2014.07-belk-3.0.0	TBD
Linux version	3.9.0-bora-1.0.0	3.9.0-bora-1.1.0	3.9.0-bora-2.0.0	3.9.0-bora-2.1.0	3.17.0-bora-2.2.0	3.17.0-bora-3.0.0	TBD
Drivers	-	-	Gigabit Eth #0 UART NOR NAND SD/MMC USB Host/Device RTC CAN I2C	Gigabit Eth #0 UART NOR NAND SD/MMC USB Host/Device RTC CAN I2C	Gigabit Eth #0 UART NOR NAND SD/MMC USB Host/Device RTC CAN I2C ConfigID	Gigabit Eth #0 UART NOR NAND SD/MMC USB Host/Device RTC CAN I2C ConfigID	TBD
Vivado version	2013.2	2013.3	2013.3	2013.3	2014.4	2014.4	2014.4
Build System	-	-	-	Yocto Daisy (1.6)	Yocto Daisy (1.6)	Yocto Daisy (1.6)	Yocto Daisy (1.6)

Downloadable binary images

TBD

microSD layout

TBD

Updates

TBD

It's recommended to use the latest available BELK version. Please refer to Release notes for further information.

Updating git repositories

In BELK, the following source trees are clones of DAVE Embedded Systems public git repositories:

Component	GIT Remote
Vivado project	git@git.dave.eu:dave/bora/bora.git
Linux	git@git.dave.eu:dave/bora/linux-xlnx.git
U-Boot	git@git.dave.eu:dave/bora/u-boot-xlnx.git

This means that these components can be kept in sync and up to date with DAVE Embedded Systems repositories.

RSA key generation

Please follow the procedure reported below to generate the RSA ssh key:

• select your username (ad es. username@myhost.com)
• start your Linux development server machine
• start a shell session
• make sure the ssh client components are installed
• enter the .ssh subdirectory into your home directory: cd ~/.ssh/
• launch the following command:
  

  ssh-keygen -t rsa -C "username@myhost.com" -f username@myhost.com

• this command creates the files ~/.ssh/username@myhost.com (private key) and ~/.ssh/username@myhost.com.pub (public key)
• edit your ~/.ssh/config adding the following lines:

Host git.dave.eu
    User git
    Hostname git.dave.eu
    PreferredAuthentications publickey
    IdentityFile ~/.ssh/username@myhost.com

Please send the public key file to the following email support addresses:

• support-bora@dave.eu

with the request for the creation of a new public git account associated to your username. The support team will enable the account and send you a confirmation as soon as possible.

Updating the repositories from BELK 2.1.0

To update the repositories from BELK 2.1.0, the following commands should be used:

git fetch origin
git checkout -b <new_branch_name> origin/bora

Synchronizing the repositories

When the account is enabled, you can synchronize a source tree entering the repository directory and launching the git fetch command. Please note that git fetch doesn't merge the commits on the current branch. To do that, you should run the git merge command or replace the fetch-merge process with a single git pull command. Please note that the recommended method is the fetch-merge process. For further information on Git, please refer to Git Documentation.

Release notes

BELK 3.0.0

Updates:

1. Added support for BORA Xpress SOM
2. Updated U-Boot and Linux versions

Known Limitations

Issue	Description
Yocto ubi-utils command line	Some Yocto ubi-utils command line are in non standard format. For ubimkvol and ubirmvol the UBI device must be the last argument (e.g. ubimkvol -m -N belk /dev/ubi0)
External DDR3 bank	The DDR3 SDRAM bank on the BoraEVB is not supported in this BELK version.
ETH1 interface	The additional Gigabit Ethernet interface (ETH1) is not supported in this BELK version.
RTC	Date/time retention is limited to about 4 hours.

BELK 2.2.0

Updates:

1. Switched to Vivado 2014.4
2. Added “board part” for the BORA SOM, which includes all the settings of the Zynq PS for BORA, allowing users to manage projects from the Vivado GUI (and not only using the CLI).
3. Added ConfigID
4. Updated U-Boot and Linux versions

Known Limitations

Issue	Description
Kernel command line	User should remove mem=xxx from kernel command line to avoid system hang during boot. This is fixed in current u-boot default environment
Yocto ubi-utils command line	Some Yocto ubi-utils command line are in non standard format. For ubimkvol and ubirmvol the UBI device must be the last argument (e.g. ubimkvol -m -N belk /dev/ubi0)
External DDR3 bank	The DDR3 SDRAM bank on the BoraEVB is not supported in this BELK version.
ETH1 interface	The additional Gigabit Ethernet interface (ETH1) is not supported in this BELK version.
RTC	Date/time retention is limited to about 4 hours.
u-boot default environment	Default u-boot environment has a syntax error on sdboot command. This is already fixed in bora-next branch, release belk-2.2.1-rc1, available on u-boot repository.

BELK 2.1.0

Updates:

1. Fix and performance improvement on u-boot network interface
2. Fix SD card hotplug issue in Linux
3. First Yocto Daisy (1.6) BSP Release

Known Limitations

Issue	Description
ETH0 interface	Primary Gigabit Ethernet Interface (ETH0) is not working correctly at 10Mbps
Kernel command line	User should remove mem=xxx from kernel command line to avoid system hang during boot
Yocto ubi-utils command line	Some Yocto ubi-utils command line are in non standard format. For ubimkvol and ubirmvol the UBI device must be the last argument (e.g. ubimkvol -m -N belk /dev/ubi0)
External DDR3 bank	The DDR3 SDRAM bank on the BoraEVB is not supported in this BELK version.
ETH1 interface	The additional Gigabit Ethernet interface (ETH1) is not supported in this BELK version.
RTC	Date/time retention is limited to about 4 hours.

BELK 2.0.0

Updates:

1. Added support for the BoraEVB carrier board
2. Updated supported drivers list (please refer to BELK_software_components)

Known Limitations

The following table reports the known limitations of this BELK release:

Issue	Description
External DDR3 bank	The DDR3 SDRAM bank on the BoraEVB is not supported in this BELK version.
ETH1 interface	The additional Gigabit Ethernet interface (ETH1) is not supported in this BELK version.
RTC	Date/time retention is limited to about 4 hours.

BELK 1.1.0

Updates:

1. Switched to Vivado 2013.3
2. Added application note "AMP on Bora"

BELK 1.0.0

First official release