Difference between revisions of "Specific SOM U-Boot Environment Variables"
DevWikiAdmin (talk | contribs) m |
DevWikiAdmin (talk | contribs) m (→Naon Family) |
||
| (5 intermediate revisions by the same user not shown) | |||
| Line 6: | Line 6: | ||
= Introduction = | = Introduction = | ||
| − | This page describes the U-Boot environment variables that specifically applies to certain | + | This page describes the U-Boot environment variables that specifically applies to certain Dave SOMs. |
== Naon Family == | == Naon Family == | ||
| − | The variables | + | The following variables applies to Naon, Maya and Dido SOMs. Please note that the this variables refers to U-Boot and Linux provided with NELK version 4.0.0. |
| − | + | <pre> | |
| − | + | ethaddr = xx:xx:xx:xx:xx:xx - MAC address for eth0 interface | |
| − | + | ethaddr1 = xx:xx:xx:xx:xx:xx - MAC address for eth1 interface | |
| − | + | dual_emac = [0|1] - [0: CPSW switch mode | 1: CPSW dual EMAC mode] | |
| − | + | cpsw = [0|1] - select primary phy for networking operations in U-Boot [0: phy 6 -> 100Mbit Naon module | 1: phy 1 -> 1Gbit external, EVB-Lite and EVB-Mid] | |
| − | + | giga = [on] - if present, select gigabit speed on gigabit link | |
| − | + | </pre> | |
| − | + | ||
| − | + | === Naon === | |
| − | + | ||
| − | |- | + | The following variables applies to Naon CPU module. Please note that the this variable refers to U-Boot and Linux provided with NELK version 4.0.0. |
| − | + | ||
| − | + | <pre> | |
| − | + | naon_host [evb_mid | evb_lite] - | |
| − | + | </pre> | |
| − | |- | + | |
| − | + | === Maya === | |
| − | + | ||
| − | + | The following variables applies to Maya CPU module. Please note that the this variable refers to U-Boot and Linux provided with NELK version 4.0.0. | |
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| + | <pre> | ||
| + | naon_host [maya_naon_evb_lite] | ||
| + | </pre> | ||
=== Dido === | === Dido === | ||
| − | The following variables applies to Dido CPU module. Please note that the this | + | The following variables applies to Dido CPU module. Please note that the this variable refers to U-Boot and Linux provided with NELK version 4.0.0. |
<pre> | <pre> | ||
addmem = 'setenv bootargs ${bootargs} mem 364M mem=320M@0x9fc00000 mem=1020M@0xc0000000 vmalloc=500M' - Dido 2 GB memory | addmem = 'setenv bootargs ${bootargs} mem 364M mem=320M@0x9fc00000 mem=1020M@0xc0000000 vmalloc=500M' - Dido 2 GB memory | ||
| + | naon_host [evb_mid | evb_lite] - | ||
</pre> | </pre> | ||
Revision as of 14:41, 24 April 2013
| HOME | SOMs | SBCs | ToloMEO Embedded Assistant |  GET A QUOTE
|
 ONLINE HELPDESK
|
| Roadmap | IoT Services | ML/AI services | Embedded Design Services |
Info Box
|
Introduction[edit | edit source]
This page describes the U-Boot environment variables that specifically applies to certain Dave SOMs.
Naon Family[edit | edit source]
The following variables applies to Naon, Maya and Dido SOMs. Please note that the this variables refers to U-Boot and Linux provided with NELK version 4.0.0.
ethaddr = xx:xx:xx:xx:xx:xx - MAC address for eth0 interface ethaddr1 = xx:xx:xx:xx:xx:xx - MAC address for eth1 interface dual_emac = [0|1] - [0: CPSW switch mode | 1: CPSW dual EMAC mode] cpsw = [0|1] - select primary phy for networking operations in U-Boot [0: phy 6 -> 100Mbit Naon module | 1: phy 1 -> 1Gbit external, EVB-Lite and EVB-Mid] giga = [on] - if present, select gigabit speed on gigabit link
Naon[edit | edit source]
The following variables applies to Naon CPU module. Please note that the this variable refers to U-Boot and Linux provided with NELK version 4.0.0.
naon_host [evb_mid | evb_lite] -
Maya[edit | edit source]
The following variables applies to Maya CPU module. Please note that the this variable refers to U-Boot and Linux provided with NELK version 4.0.0.
naon_host [maya_naon_evb_lite]
Dido[edit | edit source]
The following variables applies to Dido CPU module. Please note that the this variable refers to U-Boot and Linux provided with NELK version 4.0.0.
addmem = 'setenv bootargs ${bootargs} mem 364M mem=320M@0x9fc00000 mem=1020M@0xc0000000 vmalloc=500M' - Dido 2 GB memory
naon_host [evb_mid | evb_lite] -
