DWM ADD-ON/DWM Hardware/Pinout Table

History
Issue Date	Notes
2020/11/10	New documentation layout

Connectors and Pinout Table

Connectors description

In the following table are described all available connectors integrated on DWM_ADD-ON:

Connector name	Connector Type	Notes	Carrier board counterpart
J1	Dual in line low profile high density connector 30pins	Molex 501920-3001	Molex 52991-030, others are available with different stand-off
Antenna's connector	UFL type	N.A.	UFL cable side (many versions available in the marked already inserted on cables/antenna patches)

The dedicated carrier board must mount the mating connector and connect the desired peripheral interfaces according to DWM pinout specifications. See the images below for reference:

DWM TOP view with antenna's connector

DWM BOTTOM view with main connector

Pinout table naming conventions

This chapter contains the pinout description of the DWM module, grouped in two tables (odd and even pins) that report the pin mapping of the TBD: connector type DWM connector.

Each row in the pinout tables contains the following information:

Pin	Reference to the connector pin
Pin Name	Pin (signal) name on the DWM connectors
Internal connections	Connections to the DWM components CPU.<x> : pin connected to CPU pad named <x> CAN.<x> : pin connected to the CAN transceiver (manufacturer part number) PMIC.<x> : pin connected to the Power Manager IC (manufacturer part number) LAN.<x> : pin connected to the LAN PHY (manufacturer part number) NOR.<x>: pin connected to the flash NOR SV.<x>: pin connected to voltage supervisor MTR: pin connected to voltage monitors
Ball/pin #	Component ball/pin number connected to signal
Voltage	I/O voltage levels
Type	Pin type: I = Input O = Output D = Differential Z = High impedance S = Power supply voltage G = Ground A = Analog signal
Notes	Remarks on special pin characteristics
Pin MUX alternative functions	Muxes: Pin ALT-0 ... Pin ALT-N The number of functions depends on platform

Pinout Table ODD pins declaration

Pin	Pin Name	Internal Connections	Ball/pin #	Voltage domain	Type	Notes	Pin MUX alternative functions
J1.1	BT_EN	Bluetooth Enable		3.3V	I
J1.3	BT_CTS	Bluetooth HCI UART CTS		3.3V	I
J1.5	BT_RX	Bluetooth HCI UART RX		3.3V	I
J1.7	BT_RTS	Bluetooth HCI UART RTS		3.3V	O
J1.9	BT_TX	Bluetooth HCI UART TX		3.3V	O
J1.11	DGND	Ground		-	G
J1.13	DAT3	SDIO Data Bit 3		3.3V	D
J1.15	DAT2	SDIO Data Bit 2		3.3V	D
J1.17	DAT1	SDIO Data Bit 1		3.3V	D
J1.19	DAT0	SDIO Data Bit 0		3.3V	D
J1.21	DGND	Ground		-	G
J1.23	SDO_CMD	SDIO Command Line		3.3V	I/O
J1.25	DGND	Ground		-	G
J1.27	3.3V	+3.3V Input Voltage		3.3V	S
J1.29	5V	+5V Input Voltage		5V	S

Pinout Table EVEN pins declaration

Pin	Pin Name	Internal Connections	Ball/pin #	Voltage domain	Type	Note	Pin MUX alternative functions
J1.2	WIFI_EN	WLAN Enable		3.3V	I
J1.4	WIFI_IRQ	WLAN Interrupt Request		3.3V	O
J1.6	BT_F2	Bluetooth Wakeup		3.3V	I	Please leave unconnected if not used
J1.8	WIFI_CLK_REQ(A)	HOST_WakeUp		3.3V	O	Please leave unconnected if not used
J1.10	NC	Reserved for future use		-		Please leave unconnected.
J1.12	NC	Reserved for future use		-		Please leave unconnected.
J1.14	NC	Reserved for future use		-		Please leave unconnected.
J1.16	NC	Reserved for future use		-		Please leave unconnected.
J1.18	NC	Reserved for future use		-		Please leave unconnected.
J1.20	NC	Reserved for future use		-		Please leave unconnected.
J1.22	DGND	Ground		-	G
J1.24	SDO_CLK	SDIO Clock		3.3V	I
J1.26	DGND	Ground		-	G
J1.28	3.3V	+3.3V Input Voltage		3.3V	S
J1.30	5V	+5V Input Voltage		5V	S

---