| HOME | SOMs | SBCs | ToloMEO Embedded Assistant |  GET A QUOTE
|
 ONLINE HELPDESK
|
| Roadmap | IoT Services | ML/AI services | Embedded Design Services |
| History | |||
|---|---|---|---|
| Version | Issue Date | Notes | |
| X.Y.Z | Month Year | TBD | |
| [TBD_link X.Y.Z] | Month Year | TBD | |
| ... | ... | ... | |
Contents
Reset scheme and control signalsEdit
The following picture shows the simplified block diagram of reset scheme and voltage monitoring.
TBD: qui di seguito vanno inserite le sezioni che includano la descrizione dei segnali coinvolti nella fase di Reset, ad esempio:
- MRST
- POR
- SNVS
- SYSRST
- ...
TBD: indicare le connessioni del segnale di reset verso altri device interni (come per esempio la NOR SPI
TBD: di seguito la pagina di AXEL Lite da rivedere nel caso di altri SOM
VDDEdit
Some signals that are related to reset circuitry are pulled-up to VDD rail. This voltage is generated by the PMIC and act as power good to switch on/off the all the peripheral that could back power the CPU.
NRSTEdit
Rest signal, tie to DGND to reset the system. It is driven by the PMIC to set the CPU in reset state.
SOM_PGOODEdit
This is a convencional signal to drive DC/DC enable inputs or switch on/off control signals. It is connected to the VDD through a 22Ohm resistor.
PONKEYnEdit
User power on key (active low with internal pull-up), used to wake up the sysytem from power down.
NRST_COREEdit
Reset signal for the core, to be used if the VDD_CORE is not disabled during the reset. Internally tied to NRST signal.
PWR_ONEdit
PDR_ONEdit
PDR_ON_COREEdit
PWR_LPEdit
PMIC_VSNVSEdit
Some signals that are related to reset circuitry are pulled-up to PMIC_VSNVS. This voltage is generated by PMIC PF0100's VSNVS LDO/Switch and its actual value depends on:
- voltage applied to PMICS's VIN pin
- in case of AxelLite this pin is connected to 3.3VIN power rail
- voltage applied to PMICS's LICELL pin
- in case of AxelLite this pin is connected to pin 14 of SODIMM connector (PMIC_LICELL)
- PMIC's VSNVSCTL register configuration.
Hence it is recommended that system designer takes into account these factors in order to properly manage these signals at carrier board level.
For more details please refer to section VSNVS LDO/Switch of MMPF0100 Advance Information document.
CPU_PORnEdit
The following devices can assert this active-low signal:
- PMIC
- multiple-voltage monitor: this device monitors critical power voltages and triggers a reset pulse in case any of these exhibits a brownout condition
Since SPI NOR flash can be used as boot device, CPU_PORn is connected to this device too. This guarantees it is in a known state when reset signal is released.
Handling CPU-initiated software resetEdit
By default, MX6 processor does not assert any external signal when it initiates a software reset sequence. Also default software reset implementation does not guarantee that all processor registers are reset properly.
For these reasons, it is strongly recommended to use a different approach that, in combination with the use of a processor's watchdog timer (WDT), provides a full hardware reset in case a software reset is issued.
This technique is implemented in DESK-ETRA-L. At software level, U-Boot and Linux kernel software reset routines make use of processor's WDT #2 to assert the WDOG2_B reset signal. This signal in turn is routed to GPIO_1 pad (MUX mode = 1). At hardware level, this signal is AC-coupled to a 3-state output buffer (please refer to U22 chip of AxelEVB-Lite carrier board), driving PMIC_PWRON.