Connectors, buttons and switches (SBC Lynx)

Info Box Applies to SBC Lynx

SBC Lynx is extremely flexible in terms of hardware configurations. This document details connector's pinout of common SBC Lynx models. For more information about models not documented here, please contact Sales department.

Introduction

This document details connectors, buttons and switches that equip SBC Lynx board. Please note that not all of them are available on all models.

The following table lists connectors, buttons and switches available on SBC Lynx.

Reference	Function	Type	Part number	Notes
J35	Power supply	2-pin header, male pins, Shrouded 0.200in pitch	Phoenix 1757242 MSTBA 2.5/2-G-5.08	[1]
JP1	Power supply	2.1mm ID, 5.5mm OD	CUI PJ-002A	[1]
J42	System console	TTL 3.3V UART 4-pin Header, Male 0.100in pitch
J50	System ONOFF / Power Reset	4-pin Header, Male 0.100in pitch
J16	10/100 Base-T Ethernet port	RJ-45	Wurth 74990112116A
J43	microSD slot	push-pull slot	Molex 47571-0001
J47	USB OTG	USB type micro AB	Hirose ZX62D-AB-5P8
J55	USB OTG	USB type micro B vertical	Molex 105133-0011
J48	USB host	USB type A Right Angle	Wurth WE-614 004 134 726
J34	MPUART0 ( RS232 / RS485 / RS422 )	DB9 90° Connector Male or Female		[2]
J38	MPUART0 ( RS232 / RS485 / RS422 )	3-pins Header, Male Pins, Shrouded 0.200in pitch	Phoenix 1755749 MSTBVA2.5/3-G5.08	[2]
J21	MPUART1 ( RS232 / RS485 / RS422 / CAN)	DB9 90° Connector Male or Female		[3]
J39	MPUART1 ( RS232 / RS485 / RS422 / CAN)	3-pins Header, Male Pins, Shrouded 0.200in pitch	Phoenix 1755749 MSTBVA2.5/3-G5.08	[3]
J40	CAN	3-pins Header, Male Pins, Shrouded 0.200in pitch	Phoenix 1755749 MSTBVA2.5/3-G5.08
J46	DAVE DWM WiFi/Bluetooth module interface	30-pins SlimStack™ Receptacle 0.50mm pitch	Molex 52991-0308
J45/J52	ONE Piece	30x2 pins, pitch 1.00mm One Piece Interface	Samtec FSI-130-03-G-D-M-K-TR
J53/J54	Mezzanine Board Connectors	10-pins Header 0.100inch
S11	Reset button
S12	Boot Mode / UART Termination resistors	8-positions DIP Switches	WE-416131160808
J49	JTAG	1.27mm-pitch 5x2 header

[1] These parts are mutually exclusive.

[2] These parts are mutually exclusive.

[3] These parts are mutually exclusive.

The following image shows where connectors, buttons and switches are located.

Connectors and switches layout

Connectors

Power supply connector (J35 / JP1)

J35

Pin #	Name	Description	Notes
1	GND	Ground
2	VIN	Positive supply voltage	Range: 5 ÷ 24 V]

JP1

Pin #	Name	Description	Notes
1	VIN	Positive supply voltage	Range: 5 ÷ 24 V]
2	GND	Ground
3	GND	Ground

Serial console (J42)

System console is by default routed to this interface. This is typically used during the development stage.

Pin #	Processor ball	Name	Default function	Default type	Notes
1	K14	UART1_TX_DATA	UART1 transmit line	Output, 3.3V LVTTL
2	K16	UART1_RX_DATA	UART1 receive line	Input, 3.3V LVTTL
3	-	3V3_IO	UART1 I/O voltage reference	3.3V
4	-	DGND	Ground	0V

Ethernet connector (J16)

TBD

microSD slot (J43)

TBD

USB host port (J48)

TBD

USB OTG port (J47)

TBD

Mezzanine board connectors (J53/J54)

TBD

One-piece connectors (J45 / J52)

J45 and J52 are 1.00mm-pitch 30x2 pins One Piece interface that share the same pinout. J45 is placed on the Top side of the PCB. J52 is placed on the Bottom side of the PCB.

Some of the One Piece connector signals are reserved for internal use or shared with Mezzanine Board connectors. Please contact DAVE Embedded Systems' technical support for available configurations and for more info.

DWM WiFi/Bluetooth module Connector (J46)

TBD

Multiprotocol UARTs and CAN interfaces

TBD

Buttons

Reset button (S11)

TBD

Switches

Boot mode (S12)

Please refer to this page.

Multiprotocol UARTs/CAN settings (S12)

Please refer to TBD.