Difference between revisions of "Dacu"

From DAVE Developer's Wiki
Jump to: navigation, search
(→‎Layout)
m (→‎Connectors pinout)
(95 intermediate revisions by 4 users not shown)
Line 1: Line 1:
 
{{InfoBoxTop}}
 
{{InfoBoxTop}}
 
{{AppliesToDacu}}
 
{{AppliesToDacu}}
−
{{AppliesToAxel}}
 
−
{{AppliesToAxelLite}}
 
−
{{AppliesToAxelEsatta}}
 
−
{{Applies To Diva}}
 
 
{{AppliesToLizard}}
 
{{AppliesToLizard}}
 +
{{AppliesToAndroid}}
 
{{InfoBoxBottom}}
 
{{InfoBoxBottom}}
  
−
==Introduction==
+
===Introduction===
  
−
[[File:Dacu-top-view.png|600px|frameless|border]]
+
Dacu is an ARM Cortex-A8 industrial tablet platform, built around a carrier board hosting the [[:Category:Lizard|Lizard]] CPU module. The main system specifications are the following:
−
 
 
−
Dacu is a '''carrier board''' that can host various '''DAVE Embedded Systems''' SOMs, like, for example, the [[:Category:Lizard|Lizard]] CPU module.
 
−
{{ImportantMessage|text=Please note that DACU supports several BOM variants in order to mate with different SOMs or evaluation boards.}}
 
−
 
 
−
 
 
−
Dacu's system specifications are the following:
 
  
 
{| class="wikitable"  
 
{| class="wikitable"  
 
|-
 
|-
−
|Supported SOMs
+
|Microprocessor
−
|[[:Category:AxelUltra|Axel Ultra]]<br>[[:Category:AxelLite|Axel Lite]]<br>[[:Category:Diva|Diva]]<br>[[:Category:Lizard|Lizard]]
+
|ARM Cortex-A8 @ 500 MHz
 
|-
 
|-
 
|Power
 
|Power
Line 27: Line 18:
 
|-
 
|-
 
|Serial Ports
 
|Serial Ports
−
|1x UART RS232 on DB9<br>1x UART (RS232/RS422/RS485) or CAN on DB9 (hardware mount options)<br>1x UART RS232 on pin strip (debug port)
+
|1x UART RS232 on DB9<br>1x UART RS232/RS485/CAN on DB9<br>1x UART RS232 on pin strip (debug port)
 
|-
 
|-
 
|Ethernet
 
|Ethernet
Line 39: Line 30:
 
|-
 
|-
 
|USB
 
|USB
−
|2x USB 2.0 ports
+
|1x USB Host full speed port<br>1x USB Host high speed port
 
|-
 
|-
 
|Audio
 
|Audio
Line 52: Line 43:
 
|}
 
|}
  
−
== Block Diagram ==
+
=== Block Diagram ===
−
 
 
−
The following picture shows block diagram of the Dacu carrier board (the version for the Lizard SOM):
 
  
 +
The following picture shows block diagram of Dacu:
 
[[File:dacu-bd.png|thumbnail|center|400px]]
 
[[File:dacu-bd.png|thumbnail|center|400px]]
  
−
== Mechanicals ==
+
=== Mechanicals ===
  
 
The following picture shows the mechanical layout of Dacu:
 
The following picture shows the mechanical layout of Dacu:
 
[[File:Dacu-top.png|thumbnail|center|400px]]
 
[[File:Dacu-top.png|thumbnail|center|400px]]
  
−
== Available options ==
+
=== Connectors pinout ===
−
 
 
−
=== RS232/RS485/RS422 or CAN ===
 
−
 
 
−
=== Male or female DB9 connector ===
 
−
 
 
−
== Connectors pinout ==
 
  
 
The following section describes the on-board connectors and their pinout.
 
The following section describes the on-board connectors and their pinout.
  
−
=== Power supply ===
+
==== Power supply ====
  
 
Power is provided through the JP2 DC Power Jack. Power voltage range is [12-24 V]
 
Power is provided through the JP2 DC Power Jack. Power voltage range is [12-24 V]
  
−
=== CPU module connectors – J1, J2 ===
+
==== Lizard module connectors – J1, J2 ====
  
−
J1 and J2 are the 140-pin mating connectors for the hosted SOM.
+
J1 and J2 are the mating connectors for Lizard CPU module.
  
−
=== UART1 - J4 ===
+
==== UART1 - J4 ====
  
−
J4 is a standard DB9 connector for the RS232 four-wires UART1 port. The following table reports the connector's pinout:
+
RS232 (4-wire) -
  
−
{| class="wikitable"
+
==== UART2 - J5 ====
−
|-
 
−
!Pin#
 
−
!Pin name
 
−
!Function
 
−
!Notes
 
−
|-
 
−
|1, 4, 6, 9
 
−
|N.A.
 
−
|N.A.
 
−
|Connected to protection diode array
 
−
|-
 
−
|2
 
−
|UART_EXT_RX
 
−
|Receive line
 
−
|
 
−
|-
 
−
|3
 
−
|UART_EXT_TX
 
−
|Transmit line
 
−
|
 
−
|-
 
−
|5
 
−
|DGND
 
−
|Ground
 
−
|
 
−
|-
 
−
|7
 
−
|UART_EXT_RTS
 
−
|Request To Send line
 
−
|
 
−
|-
 
−
|8
 
−
|UART_EXT_CTS
 
−
|Clear To Send line
 
−
|
 
−
|-
 
−
|}
 
  
−
=== UART2/CAN - J5 ===
+
RS232 (4-wire)
 +
RS485 (half-duplex)
 +
CAN
  
−
J5 is a standard DB9 '''male''' connector for the configurable UART/CAN port. The board provides some '''hardware''' mount options for the selection of the UART mode (RS232/RS422/RS485 with auto-direction) or the CAN mode. The board default configuration provides the CAN interface on this port, while the RS232/RS422/RS485 interface is provided as an option to customers who choose the alternative configuration.
+
Configuration Jumper J26 e J27
  
−
Please note that this port can be used to connect a [http://www.rovingnetworks.com/products/RN240 Bluetooth serial adapter] powered by the 5V_BT signal.
+
==== UART3 - J25 ====
  
 +
Debug
  
−
The following table reports the connector's pinout:
+
==== Ethernet port - J6 ====
  
−
{| class="wikitable"
+
J6 is a standard RJ45 connectors connected to the Lizard integrated ethernet controller and PHY.
−
|-
 
−
!Pin#
 
−
!Pin name
 
−
!RS232 mode
 
−
!RS422 mode
 
−
!RS485 mode
 
−
!CAN mode
 
−
!Notes
 
−
|-
 
−
|1
 
−
|N.A./Reserved
 
−
|Not connected
 
−
|Not connected
 
−
|Not connected
 
−
|Reserved
 
−
|
 
−
|-
 
−
|2
 
−
|UART2_A/CAN_M
 
−
|UART2 rx line
 
−
|Not connected
 
−
|Not connected
 
−
|CAN bus low signal
 
−
|
 
−
|-
 
−
|3
 
−
|UART2_Y/CAN_GND
 
−
|UART2 tx line
 
−
|Inverting driver output
 
−
|Inverting driver output
 
−
|CAN bus GND
 
−
|
 
−
|-
 
−
|4
 
−
|N.A./Reserved
 
−
|Not connected
 
−
|Not connected
 
−
|Not connected
 
−
|Reserved
 
−
|
 
−
|-
 
−
|5
 
−
|DGND/CAN_SHIELD
 
−
|Ground
 
−
|Ground
 
−
|Ground
 
−
|CAN bus shield (Optional)
 
−
|
 
−
|-
 
−
|6
 
−
|N.A./GND
 
−
|Not connected
 
−
|Not connected
 
−
|Not connected
 
−
|Ground (Optional)
 
−
|
 
−
|-
 
−
|7
 
−
|UART2_Z/CAN_P
 
−
|UART2 Request To Send
 
−
|Noninverting driver output
 
−
|Noninverting driver output
 
−
|CAN bus high signal
 
−
|
 
−
|-
 
−
|8
 
−
|UART2_B/Reserved
 
−
|UART2 Clear To Send
 
−
|Not connected
 
−
|Not connected
 
−
|Reserved
 
−
|
 
−
|-
 
−
|9
 
−
|5V_BT/CAN_V+
 
−
|5V for bluetooth
 
−
|5V for bluetooth
 
−
|5V for bluetooth
 
−
|CAN bus Power (Optional)
 
−
|
 
−
|-
 
−
|}
 
  
 +
==== LCD LVDS connector - J8 ====
  
−
==== Configuration Jumpers J26 e J27 ====
 
  
−
When the board is configured to provide the UART2 interface through the J5 connector, the J26 and J27 jumpers are used to configure the UART mode, as reported below:
 
  
−
{| class="wikitable"
+
==== LCD Ziff connecor - J7 ====
−
|-
 
−
!Jumper
 
−
!RS232 mode
 
−
!RS422 mode
 
−
!RS485 mode
 
−
|-
 
−
|1-3
 
−
|open
 
−
|open
 
−
|closed
 
−
|-
 
−
|5-7
 
−
|open
 
−
|closed
 
−
|open
 
−
|-
 
−
|9-11
 
−
|open
 
−
|closed
 
−
|open
 
−
|-
 
−
|2-4
 
−
|open
 
−
|open
 
−
|closed
 
−
|-
 
−
|6-8
 
−
|open
 
−
|closed
 
−
|closed
 
−
|-
 
−
|10-12
 
−
|open
 
−
|closed
 
−
|closed
 
−
|-
 
−
|13-15
 
−
|open
 
−
|open
 
−
|closed
 
−
|-
 
−
|14-16
 
−
|open
 
−
|open
 
−
|closed
 
−
|-
 
−
|}
 
  
−
=== UART3 - J25 ===
+
Optional
  
−
J25 is a 10 pin (5x2x2.54mm) header connector. The following table reports the connector's pinout:
+
==== Touch screen connecor - J28 ====
  
−
{| class="wikitable"
+
==== MicroSD slot - J12 ====
−
|-
 
−
!Pin#
 
−
!Pin name
 
−
!Function
 
−
!Notes
 
−
|-
 
−
|1, 2, 4, 6, 7, 8, 10
 
−
|N.A.
 
−
|N.C.
 
−
|Not connected
 
−
|-
 
−
|3
 
−
|UART3_RX
 
−
|Uart Receive line
 
−
|
 
−
|-
 
−
|5
 
−
|UART3_TX
 
−
|Uart Transmit line
 
−
|
 
−
|-
 
−
|9
 
−
|DGND
 
−
|Ground
 
−
|
 
−
|-
 
−
|}
 
  
 +
==== SDIO slot (DWM module) - J14 ====
  
−
=== Ethernet port - J6 ===
+
==== USB ports - J15 ====
  
−
J6 is a standard RJ45 connectors connected to the Lizard integrated ethernet controller and PHY.
+
==== I2C bus - J18 ====
  
−
{| class="wikitable"
+
==== GPIO - J19 ====
−
|-
 
−
!Pin#
 
−
!Pin name
 
−
!Function
 
−
!Notes
 
−
|-
 
−
|1
 
−
|ETH_CTTD
 
−
|Center Tap TX
 
−
|
 
−
|-
 
−
|2
 
−
|ETH_TX+
 
−
|Eth transmit data +
 
−
|
 
−
|-
 
−
|3
 
−
|ETH_TX-
 
−
|Eth transmit data -
 
−
|
 
−
|-
 
−
|4
 
−
|ETH_RX+
 
−
|Eth receive data +
 
−
|
 
−
|-
 
−
|5
 
−
|ETH_RX-
 
−
|Eth receive data -
 
−
|
 
−
|-
 
−
|6
 
−
|ETH_CTRD
 
−
|Center Tap RX
 
−
|
 
−
|-
 
−
|7
 
−
|DGND
 
−
|Ground
 
−
|
 
−
|-
 
−
|8
 
−
|ETH_LED2
 
−
|Eth speed led
 
−
|
 
−
|-
 
−
|9
 
−
|DGND
 
−
|Ground
 
−
|
 
−
|-
 
−
|10
 
−
|ETH_LED1
 
−
|Eth activity led
 
−
|
 
−
|-
 
−
|}
 
  
−
=== LCD LVDS connector - J8 ===
+
==== SPI bus - J20 ====
  
−
J8 is a Hirose (cod. DF13A-20DP-1.25V) double row 1.25mm pitch miniature crimping connector. The following table reports the connector's pinout:
+
==== Audio - J21 ====
  
−
{| class="wikitable"
+
==== JTAG - J16 ====
−
|-
 
−
!Pin#
 
−
!Pin name
 
−
!Function
 
−
!Notes
 
−
|-
 
−
|1, 2
 
−
|3.3V_LCD
 
−
|3.3 V
 
−
|
 
−
|-
 
−
|3, 4, 7, 10, 13, 16, 19
 
−
|DGND
 
−
|Ground
 
−
|
 
−
|-
 
−
|5
 
−
|LCD_LVDS_D0-
 
−
|LVDS Data 0 -
 
−
|
 
−
|-
 
−
|6
 
−
|LCD_LVDS_D0+
 
−
|LVDS Data 0 +
 
−
|
 
−
|-
 
−
|8
 
−
|LCD_LVDS_D1-
 
−
|LVDS Data 1 -
 
−
|
 
−
|-
 
−
|9
 
−
|LCD_LVDS_D1+
 
−
|LVDS Data 1 +
 
−
|
 
−
|-
 
−
|11
 
−
|LCD_LVDS_D2-
 
−
|LVDS Data 2 -
 
−
|
 
−
|-
 
−
|12
 
−
|LCD_LVDS_D2+
 
−
|LVDS Data 2 +
 
−
|
 
−
|-
 
−
|14
 
−
|LCD_LVDS_CLK-
 
−
|LVDS clock -
 
−
|
 
−
|-
 
−
|15
 
−
|LCD_LVDS_CLK+
 
−
|LVDS clock +
 
−
|
 
−
|-
 
−
|17
 
−
|LCD_P17
 
−
|Backlight PWM
 
−
|Connected to LCD_BKLT_PWM
 
−
|-
 
−
|18
 
−
|LCD_P18
 
−
|
 
−
|Connected to 5V_LCD
 
−
|-
 
−
|20
 
−
|LCD_P20
 
−
|
 
−
|Connected to ground
 
−
|-
 
−
|21, 22
 
−
|LVDS_SHIELD
 
−
|LVDS shield
 
−
|
 
−
|-
 
−
|}
 
  
−
=== LCD Ziff connecor - J7 ===
+
Bottom
  
−
J7 is an optional connector for an Ampire AM-800480STMQW-TB0 7" 800x480 display. The following table reports the connector's pinout:
+
===Quick start===
 +
This section describes how to quick start Dacu system.
  
−
{| class="wikitable"  
+
==== "Full control" mode ====
−
|-
+
# connect the serial cable, provided with the board, to J3 pin-strip connector
−
!Pin#  
+
# connect this cable to PC COM port through a NULL-modem cable (not provided)
−
!Pin name
+
# start your favourite terminal software on PC; communication parameters are:
−
!Function
+
#* baud rate: 115200 Bps
−
!Notes
+
#* data bits: 8
−
|-
+
#* stop bits: 1
−
|1, 2, 9, 13, 17, 21, 25, 39, 40
+
#* parity: none
−
|DGND
+
# connect the system to Ethernet LAN (RJ45 connector, J6)
−
|Ground
+
# connect a 12Vcc power supply to to the power jack (JP2)
−
|
 
−
|-
 
−
|3
 
−
|LCD_PCLK
 
−
|LCD Pixel clock
 
−
|
 
−
|-
 
−
|4
 
−
|LCD_IRQ
 
−
|
 
−
|
 
−
|-
 
−
|5
 
−
|TSC_YP
 
−
|
 
−
|
 
−
|-
 
−
|6
 
−
|LCD_R0
 
−
|
 
−
|
 
−
|-
 
−
|7
 
−
|LCD_R1
 
−
|
 
−
|
 
−
|-
 
−
|8
 
−
|LCD_R2
 
−
|
 
−
|
 
−
|-
 
−
|10
 
−
|LCD_R3
 
−
|
 
−
|
 
−
|-
 
−
|11
 
−
|LCD_R4
 
−
|
 
−
|
 
−
|-
 
−
|12
 
−
|LCD_R5
 
−
|
 
−
|
 
−
|-
 
−
|14
 
−
|LCD_G0
 
−
|
 
−
|
 
−
|-
 
−
|15
 
−
|LCD_G1
 
−
|
 
−
|
 
−
|-
 
−
|16
 
−
|LCD_G2
 
−
|
 
−
|
 
−
|-
 
−
|18
 
−
|LCD_G3
 
−
|
 
−
|
 
−
|-
 
−
|19
 
−
|LCD_G4
 
−
|
 
−
|
 
−
|-
 
−
|20
 
−
|LCD_G5
 
−
|
 
−
|
 
−
|-
 
−
|22
 
−
|LCD_B0
 
−
|
 
−
|
 
−
|-
 
−
|23
 
−
|LCD_B1
 
−
|
 
−
|
 
−
|-
 
−
|24
 
−
|LCD_B2
 
−
|
 
−
|
 
−
|-
 
−
|26
 
−
|LCD_B3
 
−
|
 
−
|
 
−
|-
 
−
|27
 
−
|LCD_B4
 
−
|
 
−
|
 
−
|-
 
−
|28
 
−
|LCD_B5
 
−
|
 
−
|
 
−
|-
 
−
|29
 
−
|TSC_YM
 
−
|
 
−
|
 
−
|-
 
−
|30
 
−
|TSC_XM
 
−
|
 
−
|
 
−
|-
 
−
|31
 
−
|TSC_XP
 
−
|
 
−
|
 
−
|-
 
−
|32
 
−
|LCD_DE
 
−
|
 
−
|
 
−
|-
 
−
|33, 34
 
−
|3.3V_LCD
 
−
|
 
−
|
 
−
|-
 
−
|35, 36, 37
 
−
|5V_LCD
 
−
|
 
−
|
 
−
|-
 
−
|38
 
−
|LCD_BKLT_PWM
 
−
|
 
−
|
 
−
|-
 
−
|}
 
  
−
=== Touch screen connecor - J28 ===
+
Once power has been applied, U-Boot bootloader will be executed and the following messages will be printed on serial console:
  
−
J28 is a 1.0mm pitch 4-pin ZIF connector. The following table reports the connector's pinout:
+
<pre class="board-terminal">
 +
U-Boot 2009.11-00074-g34e0d5b-dirty (Jul 17 2012 - 11:00:55) [dacu-android-0.9.2]
  
−
{| class="wikitable"
+
AM35xx-GP ES2.0, L3-165MHz
−
|-
+
DAVE Lizard board + LPDDR/NAND
−
!Pin#
+
I2C:  ready
−
!Pin name
+
DRAM:  256 MB
−
!Function
+
Flash: 32 MB
−
!Notes
+
NAND:  1024 MiB
−
|-
+
In:    serial
−
|1
+
Out:  serial
−
|TSC_YP
+
Err:  serial
−
|Touch controller Y+
+
Die ID #7cf60001000000000160ae2d0b01e00a
−
|
+
Net:  davinci_emac_initialize
−
|-
+
Ethernet PHY: GENERIC @ 0x11
−
|2
+
DaVinci EMAC                                                                                                     
−
|TSC_XP
+
Hit any key to stop autoboot:  0                                                                                 
−
|Touch controller X+
+
=>
−
|
 
−
|-
 
−
|3
 
−
|TSC_YM
 
−
|Touch controller Y-
 
−
|
 
−
|-
 
−
|4
 
−
|TSC_XM
 
−
|Touch controller X-
 
−
|
 
−
|-
 
−
|}
 
  
−
=== MicroSD slot - J12 ===
+
</pre>
  
−
J12 is a Micro-SD card header. The following table reports the connector's pinout:
+
Once the boot process has completed, you'll get the default Android "desktop":
  
−
{| class="wikitable"
+
[[File:Android-dacu-lock-screen.jpg|thumb|none|border|450px|Android default lock screen]]
−
|-
 
−
!Pin#
 
−
!Pin name
 
−
!Function
 
−
!Notes
 
−
|-
 
−
|1
 
−
|MMC1_DAT2
 
−
|
 
−
|
 
−
|-
 
−
|2
 
−
|MMC1_DAT3
 
−
|
 
−
|
 
−
|-
 
−
|3
 
−
|MMC1_CMD
 
−
|
 
−
|
 
−
|-
 
−
|4
 
−
|MMC_3.3V
 
−
|
 
−
|
 
−
|-
 
−
|5
 
−
|MMC1_CLK
 
−
|
 
−
|
 
−
|-
 
−
|6
 
−
|DGND
 
−
|
 
−
|
 
−
|-
 
−
|7
 
−
|MMC1_DAT0
 
−
|
 
−
|
 
−
|-
 
−
|8
 
−
|MMC1_DAT1
 
−
|
 
−
|
 
−
|-
 
−
|9, 11
 
−
|SD_SHIELD
 
−
|
 
−
|
 
−
|-
 
−
|10, 12
 
−
|MMC1_DAT5
 
−
|
 
−
|
 
−
|-
 
−
|}
 
  
−
=== SDIO slot (DWM module) - J14 ===
+
Moreover, you'll have immediate access to the Android shell, so you can use the shell commands to interact with the system and see the output messages on the console. Using the serial console doesn't prevent you from using also the adb tool to access the system.
  
−
J14 is a Molex dual row 0.50mm pitch SlimStack™ receptacle. This connector is dedicated to the [[Wireless_Module_(DWM) | DWM add-on module]].The following table reports the connector's pinout:
+
==== "Normal" mode ====
 +
# connect the system to Ethernet LAN (RJ45 connector, J6)
 +
# connect a 12Vcc power supply to to the power jack (JP2)  
  
−
{| class="wikitable"
+
Once power has been applied, the system will boot loading the software components from the internal flash. Once the boot process has completed, you'll get the default Android "desktop":
−
|-
 
−
!Pin#
 
−
!Pin name
 
−
!Function
 
−
!Notes
 
−
|-
 
−
|1, 2
 
−
|5V
 
−
|
 
−
|
 
−
|-
 
−
|3, 4
 
−
|3.3V
 
−
|
 
−
|
 
−
|-
 
−
|5, 6, 9, 10, 19
 
−
|DGND
 
−
|
 
−
|
 
−
|-
 
−
|7
 
−
|MMC2_CMD
 
−
|
 
−
|
 
−
|-
 
−
|8
 
−
|MMC2_CLK
 
−
|
 
−
|
 
−
|-
 
−
|11
 
−
|MMC2_DAT0
 
−
|
 
−
|
 
−
|-
 
−
|12, 14, 16, 18, 20, 22
 
−
|N.C.
 
−
|Not connected
 
−
|
 
−
|-
 
−
|13
 
−
|MMC2_DAT1
 
−
|
 
−
|
 
−
|-
 
−
|15
 
−
|MMC2_DAT2
 
−
|
 
−
|
 
−
|-
 
−
|17
 
−
|MMC2_DAT3
 
−
|
 
−
|
 
−
|-
 
−
|21
 
−
|UART2_RX
 
−
|
 
−
|Mount option
 
−
|-
 
−
|23
 
−
|UART2_CTS
 
−
|
 
−
|Mount option
 
−
|-
 
−
|24
 
−
|BT_F5
 
−
|
 
−
|Connected to DSS_DATA20/DSI_DY1
 
−
|-
 
−
|25
 
−
|UART2_TX
 
−
|
 
−
|Mount option
 
−
|-
 
−
|26
 
−
|BT_F2
 
−
|
 
−
|Connected to DSS_DATA21/DSI_DX1
 
−
|-
 
−
|27
 
−
|UART2_RTS
 
−
|
 
−
|Mount option
 
−
|-
 
−
|28
 
−
|WIFI_IRQ
 
−
|
 
−
|Connected to DSS_DATA22/DSI_DY2
 
−
|-
 
−
|29
 
−
|BT_EN
 
−
|
 
−
|Connected to DSS_DATA19/DSI_DX0
 
−
|-
 
−
|30
 
−
|WIFI_EN
 
−
|
 
−
|Connected to DSS_DATA23/DSI_DX2
 
−
|-
 
−
|}
 
  
−
=== USB ports - J15 ===
+
You can now access the system using adb.
  
−
J15 is a stacked, dual port USB Type A connector.
 
  
−
==== USB port 0 (''high speed'') ====
+
==== Default IP address ====
  
−
USB port 0 is mapped on the '''lower''' USB connector. The following table reports the connector's pinout:
+
{{ImportantMessage|text='''The default IP address is 192.168.0.122'''}}
  
−
{| class="wikitable"
 
−
|-
 
−
!Pin#
 
−
!Pin name
 
−
!Function
 
−
!Notes
 
−
|-
 
−
|B1
 
−
|5V_USBH_0
 
−
|5V
 
−
|
 
−
|-
 
−
|B2
 
−
|USB0_DM
 
−
|USB0 Data -
 
−
|
 
−
|-
 
−
|B3
 
−
|USB0_DP
 
−
|USB0 Data +
 
−
|
 
−
|-
 
−
|B4
 
−
|DGND_USBH_0
 
−
|
 
−
|Ground
 
−
|-
 
−
|}
 
  
−
==== USB port 1 (''full speed'') ====
+
==== Running the Android Debug Bridge (ADB) ====
  
−
USB port 1 is mapped on the '''higher''' USB connector. The following table reports the connector's pinout:
+
[http://developer.android.com/tools/help/adb.html ADB] is a fundamental development tool and enables remote access to the Android device. ADB is provided with the Android SDK, so before using it you must install the SDK.
  
−
{| class="wikitable"
+
To establish the ADB connection, on a '''Linux''' host machine open a shell and launch the following commands:
−
|-
 
−
!Pin#
 
−
!Pin name
 
−
!Function
 
−
!Notes
 
−
|-
 
−
|A1
 
−
|5V_USBH_1
 
−
|5V
 
−
|
 
−
|-
 
−
|A2
 
−
|USBM1
 
−
|USB0 Data -
 
−
|
 
−
|-
 
−
|A3
 
−
|USBP1
 
−
|USB1 Data +
 
−
|
 
−
|-
 
−
|A4
 
−
|DGND_USBH_1
 
−
|Ground
 
−
|
 
−
|-
 
−
|}
 
  
−
=== I2C bus - J18 ===
+
<pre class="workstation-terminal">
 +
$ export PATH=${PATH}:<your_sdk_dir>/platform-tools
 +
$ export ADBHOST=<target's ip address>
 +
$ adb kill-server
 +
$ adb start-server
 +
</pre>
  
−
J18 is a 8-pin 1.25mm pitch vertical header. The following table reports the connector's pinout:
+
On a '''Windows''' host machine, open a shell and launch the following commands:
  
−
{| class="wikitable"  
+
<pre class="workstation-terminal">
−
|-
+
adb tcpip 5555
−
!Pin#
+
adb connect <target's ip address>:5555
−
!Pin name
+
adb kill-server
−
!Function
+
adb start-server
−
!Notes
+
</pre>
−
|-
 
−
|1, 5
 
−
|DGND
 
−
|Ground
 
−
|
 
−
|-
 
−
|4, 8
 
−
|3.3V
 
−
|3.3 V
 
−
|
 
−
|-
 
−
|2
 
−
|I2C2_SDA
 
−
|I2C #2 data
 
−
|
 
−
|-
 
−
|3
 
−
|I2C2_SCL
 
−
|I2C #2 clock
 
−
|
 
−
|-
 
−
|6
 
−
|I2C3_SDA
 
−
|I2C #3 data
 
−
|
 
−
|-
 
−
|7
 
−
|I2C3_SCL
 
−
|I2C #3 clock
 
−
|
 
−
|-
 
−
|}
 
  
−
=== GPIO - J19 ===
 
  
−
J19 is a 8-pin 1.25mm pitch vertical header. The following table reports the connector's pinout:
+
To check the connection, please launch
  
−
{| class="wikitable"  
+
<pre class="workstation-terminal">
−
|-
+
$ adb devices
−
!Pin#
+
</pre>
−
!Pin name
 
−
!Function
 
−
!Notes
 
−
|-
 
−
|1, 8
 
−
|DGND
 
−
|Ground
 
−
|
 
−
|-
 
−
|2
 
−
|MCBSP1_CLKX
 
−
|GPIO
 
−
|
 
−
|-
 
−
|3
 
−
|MCBSP1_DX
 
−
|GPIO
 
−
|
 
−
|-
 
−
|4
 
−
|MCBSP1_FSX
 
−
|GPIO
 
−
|
 
−
|-
 
−
|5
 
−
|MCBSP3_DR
 
−
|GPIO
 
−
|
 
−
|-
 
−
|6
 
−
|MCBSP3_FSX
 
−
|GPIO
 
−
|
 
−
|-
 
−
|7
 
−
|MCBSP4_DR
 
−
|GPIO
 
−
|
 
−
|-
 
−
|}
 
  
−
=== SPI bus - J20 ===
+
If everything is working properly, you should see the following messages:
  
−
J20 is a 8-pin 1.25mm pitch vertical header. The following table reports the connector's pinout:
+
<pre class="workstation-terminal">
 +
$ adb devices
 +
List of devices attached
 +
emulator-5554    device
 +
</pre>
  
−
{| class="wikitable"
+
You can open a remote shell using the following command:
−
|-
 
−
!Pin#
 
−
!Pin name
 
−
!Function
 
−
!Notes
 
−
|-
 
−
|1
 
−
|DGND
 
−
|Ground
 
−
|
 
−
|-
 
−
|2
 
−
|MCSPI1_CLK
 
−
|SPI1 clock
 
−
|
 
−
|-
 
−
|3
 
−
|MCSPI1_CS0
 
−
|SPI1 chip select #0
 
−
|
 
−
|-
 
−
|4
 
−
|MCSPI1_CS1
 
−
|SPI1 chip select #1
 
−
|
 
−
|-
 
−
|5
 
−
|MCSPI1_CS2
 
−
|SPI1 chip select #2
 
−
|
 
−
|-
 
−
|6
 
−
|MCSPI1_SOMI
 
−
|SPI1 slave output master input
 
−
|
 
−
|-
 
−
|7
 
−
|MCSPI1_SIMO
 
−
|SPI1 slave input master output
 
−
|
 
−
|-
 
−
|8
 
−
|3.3V
 
−
|3.3 V
 
−
|
 
−
|-
 
−
|}
 
−
 
 
−
=== Audio - J21 ===
 
  
−
J21 is a 8-pin 1.25mm pitch vertical header. The following table reports the connector's pinout:
+
<pre class="workstation-terminal">
 +
$ adb shell
 +
</pre>
  
−
{| class="wikitable"
+
To install an application (in .apk format), you can use the following commmand:
−
|-
 
−
!Pin#
 
−
!Pin name
 
−
!Function
 
−
!Notes
 
−
|-
 
−
|1
 
−
|AUD_PW2
 
−
|Audio amplifier VO 2
 
−
|
 
−
|-
 
−
|2
 
−
|AUD_PW1
 
−
|Audio amplifier VO 1
 
−
|
 
−
|-
 
−
|3, 5, 7
 
−
|DGND
 
−
|Ground
 
−
|
 
−
|-
 
−
|4
 
−
|LINEOUT_R
 
−
|Audio coded lineout right
 
−
|
 
−
|-
 
−
|6
 
−
|LINEOUT_L
 
−
|Audio coded lineout left
 
−
|
 
−
|-
 
−
|8
 
−
|MIC_INPUT
 
−
|Microphone input
 
−
|
 
−
|-
 
−
|}
 
−
 
 
−
=== JTAG - J16 ===
 
−
 
 
−
J16 is a standard 20-pin 2.54mm pitch header connector (bottom side). The following table reports the connector's pinout:
 
−
 
 
−
{| class="wikitable"
 
−
|-
 
−
!Pin#
 
−
!Pin name
 
−
!Function
 
−
!Notes
 
−
|-
 
−
|1, 2
 
−
|3.3V
 
−
|3.3 V
 
−
|
 
−
|-
 
−
|3
 
−
|JTAG_TRSTn
 
−
|
 
−
|
 
−
|-
 
−
|5
 
−
|JTAG_TDI
 
−
|
 
−
|
 
−
|-
 
−
|7
 
−
|JTAG_TMS
 
−
|
 
−
|
 
−
|-
 
−
|9
 
−
|JTAG_TCK
 
−
|
 
−
|
 
−
|-
 
−
|11
 
−
|JTAG_RTCK
 
−
|
 
−
|
 
−
|-
 
−
|13
 
−
|JTAG_TDO
 
−
|
 
−
|
 
−
|-
 
−
|15
 
−
|JTAG_RST#
 
−
|
 
−
|Connected to MRSTn
 
−
|-
 
−
|4, 6, 8, 10, 12, 14, 16, 18, 20
 
−
|DGND
 
−
|Ground
 
−
|
 
−
|-
 
−
|17, 19
 
−
|N.A.
 
−
|Not connected
 
−
|
 
−
|-
 
−
|}
 
  
−
== Versions ==
+
<pre class="workstation-terminal">
−
As stated before, different versions of DACU board exist in order to support several SOMs and evaluation boards.
+
$ adb install <path to apk>
 +
</pre>
  
−
The following pages provide some additional information (including '''schematics''' and '''BOMs''') related to the mating of DACU with the supported SOMs.
+
===Useful Links===
−
* [[Dacu for the Diva SOM]]
 
−
* [[Dacu for the Axel SOM]]
 
  
−
==Layout==
+
[http://www.youtube.com/watch?v=VhvlZL46R5Q Video: Android Multitouch demo on Dacu]
−
* http://mirror.dave.eu/diva/dacu//dacu-CS091612C_component_view.pdf
 
  
−
==Mechanical==
+
[http://developer.android.com/tools/help/adb.html Android Debug Bridge]
−
* DXF: http://mirror.dave.eu/diva/dacu/dacu_2D_CS091612C.zip
 
−
* IDF (3D): http://mirror.dave.eu/diva/dacu//dacu_3D_CS091612C.zip
 

Revision as of 10:12, 22 March 2013

HOME SOMs SBCs ToloMEO Embedded Assistant Sale-tag.pngGET A QUOTE Customer-service.pngONLINE HELPDESK
Roadmap IoT Services ML/AI services Embedded Design Services
Info Box
Dacu-top-view.png Applies to Dacu
Lizard.jpg Applies to Lizard
Android-logo.jpg Applies to Android

Introduction[edit | edit source]

Dacu is an ARM Cortex-A8 industrial tablet platform, built around a carrier board hosting the Lizard CPU module. The main system specifications are the following:

Microprocessor ARM Cortex-A8 @ 500 MHz
Power 12-24 V
Serial Ports 1x UART RS232 on DB9
1x UART RS232/RS485/CAN on DB9
1x UART RS232 on pin strip (debug port)
Ethernet 1x Fast Ethernet on RJ45 connector
Display 7" 800x480 LVDS
Storage 1x microSD slot
USB 1x USB Host full speed port
1x USB Host high speed port
Audio UDA1345 codec
Buses I2C
SPI
Other On board touch controller
Optional Wi-Fi module
GPIOs

Block Diagram[edit | edit source]

The following picture shows block diagram of Dacu:

Dacu-bd.png

Mechanicals[edit | edit source]

The following picture shows the mechanical layout of Dacu:

Dacu-top.png

Connectors pinout[edit | edit source]

The following section describes the on-board connectors and their pinout.

Power supply[edit | edit source]

Power is provided through the JP2 DC Power Jack. Power voltage range is [12-24 V]

Lizard module connectors – J1, J2[edit | edit source]

J1 and J2 are the mating connectors for Lizard CPU module.

UART1 - J4[edit | edit source]

RS232 (4-wire) -

UART2 - J5[edit | edit source]

RS232 (4-wire) RS485 (half-duplex) CAN

Configuration Jumper J26 e J27

UART3 - J25[edit | edit source]

Debug

Ethernet port - J6[edit | edit source]

J6 is a standard RJ45 connectors connected to the Lizard integrated ethernet controller and PHY.

LCD LVDS connector - J8[edit | edit source]

LCD Ziff connecor - J7[edit | edit source]

Optional

Touch screen connecor - J28[edit | edit source]

MicroSD slot - J12[edit | edit source]

SDIO slot (DWM module) - J14[edit | edit source]

USB ports - J15[edit | edit source]

I2C bus - J18[edit | edit source]

GPIO - J19[edit | edit source]

SPI bus - J20[edit | edit source]

Audio - J21[edit | edit source]

JTAG - J16[edit | edit source]

Bottom

Quick start[edit | edit source]

This section describes how to quick start Dacu system.

"Full control" mode[edit | edit source]

  1. connect the serial cable, provided with the board, to J3 pin-strip connector
  2. connect this cable to PC COM port through a NULL-modem cable (not provided)
  3. start your favourite terminal software on PC; communication parameters are:
    • baud rate: 115200 Bps
    • data bits: 8
    • stop bits: 1
    • parity: none
  4. connect the system to Ethernet LAN (RJ45 connector, J6)
  5. connect a 12Vcc power supply to to the power jack (JP2)

Once power has been applied, U-Boot bootloader will be executed and the following messages will be printed on serial console: 

U-Boot 2009.11-00074-g34e0d5b-dirty (Jul 17 2012 - 11:00:55) [dacu-android-0.9.2]

AM35xx-GP ES2.0, L3-165MHz
DAVE Lizard board + LPDDR/NAND
I2C:   ready
DRAM:  256 MB
Flash: 32 MB
NAND:  1024 MiB
In:    serial
Out:   serial
Err:   serial
Die ID #7cf60001000000000160ae2d0b01e00a
Net:   davinci_emac_initialize
Ethernet PHY: GENERIC @ 0x11
DaVinci EMAC                                                                                                       
Hit any key to stop autoboot:  0                                                                                   
=>

Once the boot process has completed, you'll get the default Android "desktop":

Android default lock screen

Moreover, you'll have immediate access to the Android shell, so you can use the shell commands to interact with the system and see the output messages on the console. Using the serial console doesn't prevent you from using also the adb tool to access the system.

"Normal" mode[edit | edit source]

  1. connect the system to Ethernet LAN (RJ45 connector, J6)
  2. connect a 12Vcc power supply to to the power jack (JP2)

Once power has been applied, the system will boot loading the software components from the internal flash. Once the boot process has completed, you'll get the default Android "desktop":

You can now access the system using adb.


Default IP address[edit | edit source]

200px-Emblem-important.svg.png

The default IP address is 192.168.0.122


Running the Android Debug Bridge (ADB)[edit | edit source]

ADB is a fundamental development tool and enables remote access to the Android device. ADB is provided with the Android SDK, so before using it you must install the SDK.

To establish the ADB connection, on a Linux host machine open a shell and launch the following commands: 

$ export PATH=${PATH}:<your_sdk_dir>/platform-tools
$ export ADBHOST=<target's ip address>
$ adb kill-server
$ adb start-server

On a Windows host machine, open a shell and launch the following commands: 

adb tcpip 5555
adb connect <target's ip address>:5555
adb kill-server
adb start-server


To check the connection, please launch 

$ adb devices

If everything is working properly, you should see the following messages: 

$ adb devices
List of devices attached
emulator-5554    device

You can open a remote shell using the following command: 

$ adb shell

To install an application (in .apk format), you can use the following commmand: 

$ adb install <path to apk>

Useful Links[edit | edit source]

Video: Android Multitouch demo on Dacu

Android Debug Bridge

HOME SOMs SBCs ToloMEO Embedded Assistant Sale-tag.pngGET A QUOTE Customer-service.pngONLINE HELPDESK
Roadmap IoT Services ML/AI services Embedded Design Services
Retrieved from "https://wiki.dave.eu/index.php?title=Dacu&oldid=1818"