5,263 bytes added,
14:46, 2 October 2018 {{InfoBoxTop}}
{{Applies To SDVX}}
{{InfoBoxBottom}}
==Introduction==
[[File:SDV03.png|500px|frameless|border]]
SDV03 is a carrier board designed to host [[:Category:AxelLite|AXEL LITE]] SoMs. It exports major standard peripherals connectors like ethernet, SD, USB, resistive touchscreen, LVDS, audio speaker.
==Block Diagram==
The following picture shows SDV03's block diagram:
[[File:SDV03_BD.png|700px|frameless|border|centre]]
==Connection layout==
The following picture shows SDV03's connection layout:
[[File:SDV03-connectors.png|700px|frameless|border|centre]]
== Features ==
* 10/100 Ethernet
* 1x USB HOST - standard Type A
* 1x USB HOST - on 2x5x2.54mm connector
* 1x Serial port (RS232) - on 2.5x2.54mm connector
* Single channel LVDS connector - direct connection to 7" 800x480 LCD panel
* resistive touchscreen connector
* speaker connector with internal power amplifier
* Battery connector (for M41T83 RTC)
== Connectors pinout ==
=== J1400 - PSU ===
J1400 is a standard plug jack connector. The following table reports the connector's pinout:
{| class="wikitable"
|-
!Pin#
!Pin name
!Function
!Notes
|-
|1 || DGND|| Ground || -
|-
|2 || EXT_12V|| 12V Power Supply || -
|-
|}
=== J400 - SODIMM connector ===
J400 is a TE Connectivity 204-pin SODIMM socket. The pinout matches the [[Pinout_(AxelLite) | Axel Lite pinout]].
=== J1101 - JTAG ===
J1101 is a SAMTEC FSI-110-03-G-S connector. The following table reports the connector's pinout:
{| class="wikitable"
|-
!Pin#
!Pin name
!Function
!Notes
|-
|1 || DGND || - || -
|-
|2 || JTAG_TCK || - || -
|-
|3 || JTAG_TMS || - || -
|-
|4 || JTAG_TDO || - || -
|-
|5 || JTAG_TDI || - || -
|-
|6 || JTAG_nTRST || - || -
|-
|7 || CPU_PORn || - || -
|-
|8 || N.C. || - || -
|-
|9 || N.C. || - || -
|-
|10 || JTAG_VREF || - || -
|-
|}
=== Console - J1100 ===
J1100 is a 4x2.54mm pin header providing access to u-boot and linux debug console port.
{| class="wikitable"
|-
!Pin#
!Pin name
!Function
!Notes
|-
|1 || UART3_TX_DATA || UART3 transmit line || -
|-
|2 || UART3_RX_DATA || UART3 receive line || -
|-
|3 || 3V3 || 3.3V Power Supply || -
|-
|4 ||DGND || Ground || -
|-
|}
J1100 connector is compatible with FTDI TTL-232RG-VIP-WE cable. To connect it, please use this wiring:
* J1100.1: yellow wire
* J1100.2: orange wire
* J1100.3: red wire
* J1100.4: black wire
=== MicroSD - J601 ===
J601 is a microSD memory card connector. It can be used as a <b>boot device</b> properly configuring the J1000 switch connector.
The following table reports the connector's pinout:
{| class="wikitable"
|-
!Pin#
!Pin name
!Function
!Notes
|-
|1 ||SD1_DAT2||| DATA[2] || -
|-
|2 ||SD1_DAT3||| Card Detect/DATA[3] || -
|-
|3 ||SD1_CMD||| CMD line || -
|-
|4 ||VDD||| 3.3V Power Supply || -
|-
|5 ||SD1_CLK||| Clock || -
|-
|6, 9, 10, 11, 12 ||DGND||| - || -
|-
|7 ||SD1_DAT0||| DATA[0] || -
|-
|8 ||SD1_DAT1||| DATA[1] || -
|-
|10 ||GND|| Card detect || -
|-
|}
=== USB HOST - J700 ===
J7001 is a standard USB Type A Female host connector.
The following table reports the connector's pinout:
{| class="wikitable"
|-
!Pin#
!Pin name
!Function
!Notes
|-
|1 ||5V || VDD || -
|-
|2 ||USB_DN || USB Data- || -
|-
|3 ||USB_DP || USB Data+ || -
|-
|4 ||DGND || Ground || -
|-
|}
=== USB Host - J701 ===
J701 is a standard 2x5x2.54mm male box header. It's pinout provide connection to USB2 host port and an RS232 serial port (see UART2 RS232)
The following table reports the connector's pinout:
{| class="wikitable"
|-
!Pin#
!Pin name
!Function
!Notes
|-
|1 ||5V || VDD || -
|-
|3 ||USB_OTG_DN || USB OTG Data- || -
|-
|5 ||USB_OTG_DP || USB OTG Data+ || -
|-
|7 ||DGND || Ground || -
|-
|}
=== TOUCH - J1201 ===
J1201 is Wurth 68610414122 4 pin connector. It can be used to interface a resistive touchscreen device integrated into a standard LCD panel.
The following table reports the connector's pinout:
{| class="wikitable"
|-
!Pin#
!Pin name
!Function
!Notes
|-
|1 || YP || || -
|-
|2 || XP || || -
|-
|3 || YM || || -
|-
|4 || XM || || -
|-
|}
=== LVDS - J1200 ===
J1200 is a 10x2 DF13A-20DP header. The following table reports the connector's pinout:
{| class="wikitable"
|-
!Pin#
!Pin name
!Function
!Notes
|-
|1, 2 ||3.3V_LCD0 || +3.3V || -
|-
|4, 7, 10,<br>13, 16, 19 ||DGND || Ground || -
|-
|3 || GPIO || VDD or GND (internal mount) || -
|-
|5 || LVDS_TX0_N || TX0- || -
|-
|6 || LVDS_TX0_P || TX0+ || -
|-
|9 || LVDS_TX1_P || TX1+ || -
|-
|8 || LVDS_TX1_N || TX1- || -
|-
|11 || LVDS_TX2_N|| TX2- || -
|-
|12|| LVDS_TX2_P|| TX2+ || -
|-
|14 || LVDS_CLK_N || Clock- || -
|-
|15 || LVDS_CLK_P || Clock+ || -
|-
|17 || BL PWM || Backlight PWM control || -
|-
|18 || 5V LCD || Backlight 5V power supply - || -
|-
|20 || GND || || -
|-
|}
=== Speaker - J1800 ===
J14 is a Molex 53398-0271 2x1.25mm pin connector.
The following table reports the connector's pinout:
{| class="wikitable"
|-
!Pin#
!Pin name
!Function
!Notes
|-
|1 ||SPKM || Speaker - output || -
|-
|2 ||SPKP || Speaker + output || -
|-
|}
== DIP SWITCH - S1000 ==
{| class="wikitable" !NaonEVB-Mid Boot Settings
|-
!DIP SWITCH
!OFF Position
!ON Position
|-
|S1000.1
|Coin cell battery disconnected
|Coin cell battery connected to RTC VBAT
|-
|S1000.2
|Boot from eMMC
|Boot from SD