767
edits
Changes
Created page with "{{InfoBoxTop}} {{AppliesToSBCLynx}} {{AppliesToAddOnSBCLynx}} {{InfoBoxBottom}} __FORCETOC__ ==Introduction== As known, SBC Lynx is conceived to allow the customer to plug in..."
{{InfoBoxTop}}
{{AppliesToSBCLynx}}
{{AppliesToAddOnSBCLynx}}
{{InfoBoxBottom}}
__FORCETOC__
==Introduction==
As known, SBC Lynx is conceived to allow the customer to plug in some additional boards to the mainboard.
This document lists some examples of such add-ons. These boards provide more interfaces to the SBC, augment expansion pin availability or add the possibility to use a custom board suitable for every needs.
Not all SBC Lynx models support every listed add-on. We recommend to check the compatibility list of each add-on.
==Extra Ethernet interface (XUAE)==
This Addon allows to add an ethernet connector and a 10/100 ethernet interface to SBC Lynx. The interface is seen as an indipendent port and can be easily fully standalone configured.
[[File:SBCLYNX_ADDON_XUAE.JPG|400px|frameless|border]]
This add on is mounted on J52 One Piece connector site in SBC Lynx mainboard and is locked by 3 screws, 2 for J52 and 1 for PEM. PEM provides SHIELD connection to mainboard PCB Ring for improve common noise immunity.
[[File:SBCLYNX_ADDON_XUAE Mounted.JPG|400px|frameless|border]]
=== Technical Specifications ===
{| class="wikitable"
|+Technical Specifications
|-
|'''Feature'''
|'''Description'''
|'''Ports'''
|-
| 10/100 Eth Port||Standard Ethernet Port||1
|-
|}
=== Pinout ===
Above table lists only used pins
{| class="wikitable"
|+Pinout
|-
|'''Connector'''
|'''PIN'''
|'''Pin Name'''
|'''Description or Usage'''
|-
| J52||1||DGND||System DGND
|-
| J52||13||DGND||System DGND
|-
| J52||20||ETH_INT||Interrupt from PHY ETH
|-
| J52||22||ETH_PHY_RST||CPU Reset Signal for PHY ETH
|-
| J52||24||DGND||System DGND
|-
| J52||26||ENET2_RX_DATA0||RMII Signal for PHY ETH
|-
| J52||28||ENET2_RX_DATA1||RMII Signal for PHY ETH
|-
| J52||30||ENET2_RX_EN||RMII Signal for PHY ETH
|-
| J52||29||DGND||System DGND
|-
| J52||32||ENET2_TX_DATA0||RMII Signal for PHY ETH
|-
| J52||34||ENET2_TX_DATA1||RMII Signal for PHY ETH
|-
| J52||36||ENET2_TX_EN||RMII Signal for PHY ETH
|-
| J52||38||ENET2_TX_CLK||RMII Signal for PHY ETH
|-
| J52||40||ENET2_RX_ER||RMII Signal for PHY ETH
|-
| J52||42||DGND||System DGND
|-
| J52||43||DGND||System DGND
|-
| J52||44||GPIO_IO07||MII BUS
|-
| J52||46||GPIO_IO07||MII BUS
|-
| J52||53||CPU_PORn||System Reset Signal for PHY ETH
|-
| J52||55||3V3_AUX||Power Supply
|-
| J52||59||3V3_AUX||Power Supply
|-
| J52||60||3V3_AUX||Power Supply
|-
|}
=== Compatibility list ===
SBC Lynx that supports this add-ons:
* S-XUBBx1xxxxR
{{AppliesToSBCLynx}}
{{AppliesToAddOnSBCLynx}}
{{InfoBoxBottom}}
__FORCETOC__
==Introduction==
As known, SBC Lynx is conceived to allow the customer to plug in some additional boards to the mainboard.
This document lists some examples of such add-ons. These boards provide more interfaces to the SBC, augment expansion pin availability or add the possibility to use a custom board suitable for every needs.
Not all SBC Lynx models support every listed add-on. We recommend to check the compatibility list of each add-on.
==Extra Ethernet interface (XUAE)==
This Addon allows to add an ethernet connector and a 10/100 ethernet interface to SBC Lynx. The interface is seen as an indipendent port and can be easily fully standalone configured.
[[File:SBCLYNX_ADDON_XUAE.JPG|400px|frameless|border]]
This add on is mounted on J52 One Piece connector site in SBC Lynx mainboard and is locked by 3 screws, 2 for J52 and 1 for PEM. PEM provides SHIELD connection to mainboard PCB Ring for improve common noise immunity.
[[File:SBCLYNX_ADDON_XUAE Mounted.JPG|400px|frameless|border]]
=== Technical Specifications ===
{| class="wikitable"
|+Technical Specifications
|-
|'''Feature'''
|'''Description'''
|'''Ports'''
|-
| 10/100 Eth Port||Standard Ethernet Port||1
|-
|}
=== Pinout ===
Above table lists only used pins
{| class="wikitable"
|+Pinout
|-
|'''Connector'''
|'''PIN'''
|'''Pin Name'''
|'''Description or Usage'''
|-
| J52||1||DGND||System DGND
|-
| J52||13||DGND||System DGND
|-
| J52||20||ETH_INT||Interrupt from PHY ETH
|-
| J52||22||ETH_PHY_RST||CPU Reset Signal for PHY ETH
|-
| J52||24||DGND||System DGND
|-
| J52||26||ENET2_RX_DATA0||RMII Signal for PHY ETH
|-
| J52||28||ENET2_RX_DATA1||RMII Signal for PHY ETH
|-
| J52||30||ENET2_RX_EN||RMII Signal for PHY ETH
|-
| J52||29||DGND||System DGND
|-
| J52||32||ENET2_TX_DATA0||RMII Signal for PHY ETH
|-
| J52||34||ENET2_TX_DATA1||RMII Signal for PHY ETH
|-
| J52||36||ENET2_TX_EN||RMII Signal for PHY ETH
|-
| J52||38||ENET2_TX_CLK||RMII Signal for PHY ETH
|-
| J52||40||ENET2_RX_ER||RMII Signal for PHY ETH
|-
| J52||42||DGND||System DGND
|-
| J52||43||DGND||System DGND
|-
| J52||44||GPIO_IO07||MII BUS
|-
| J52||46||GPIO_IO07||MII BUS
|-
| J52||53||CPU_PORn||System Reset Signal for PHY ETH
|-
| J52||55||3V3_AUX||Power Supply
|-
| J52||59||3V3_AUX||Power Supply
|-
| J52||60||3V3_AUX||Power Supply
|-
|}
=== Compatibility list ===
SBC Lynx that supports this add-ons:
* S-XUBBx1xxxxR
