Bureaucrats, dave_user, Administrators
8,186
edits
Changes
no edit summary
<section end=CPU/>
<section begin=Power Supply/>
=== Power supply - J7 ===
|-
|}
==== POWER GOOD signals selector - J10 ====
J10 is a 8-pin 4x2x2.54 pitch vertical header used for the selection - through jumpers - of the POWER GOOD options. The following table reports the pinout of the connector:
{| class="wikitable"
|-
!Pin#
!Pin name
!Function
!Notes
|-
|1 || BOARD_PGOOD|| - || -
|-
|2, 4 || 3.3V_SOM|| - || -
|-
|3 || 1.5V_POWER_GOOD || - || -
|-
|5 || VREF_POWER_GOOD || - || -
|-
|6, 8 || 3.3V_SBY || - || -
|-
|7 || 1.8V_POWER_GOOD || - || -
|-
|}
The available configurations are:
* No jumpers mounted (DEFAULT)
* Jumper on 1-2 -> supply BOARD_PGOOD with 3.3V_SOM
* Jumper on 3-4 -> supply 1.5V_POWER_GOOD with 3.3V_SOM
* Jumper on 5-6 -> supply 1.5V_VREF_POWER_GOOD with 3.3V_SBY
* Jumper on 7-8 -> supply 1.8V_VREF_POWER_GOOD with 3.3V_SBY
==== BANK35, BANK13 VDDIO selector - J11 ====
J11 is a 8-pin 4x2x2.54 pitch vertical header used for the selection - through jumpers - of the bank supply voltages. The following table reports the pinout of the connector:
{| class="wikitable"
|-
!Pin#
!Pin name
!Function
!Notes
|-
|1, 5 || 3.3V|| - || -
|-
|2, 4 || VDDIO_BANK35|| - || -
|-
|3 || EVB_VDDQ_1V5 || - || -
|-
|6, 8 || VDDIO_BANK13|| - || -
|-
|7 || EVB_VDDIO_BANK13|| - || -
|-
|}
The available configurations are:
# Jumper on 1-2 -> supply VDDIO_BANK35 with 3.3V ('''requirerd when EVBB DDR3 device is used''')
# Jumper on 3-4 -> ('''Not Available''') supply VDDIO_BANK35 with EVB_VDDQ_1V5 ('''requirerd when EVBB DDR3 device is used''')
# Jumper on 5-6 -> supply VDDIO_BANK13 with 3.3V
# Jumper on 7-8 -> supply VDDIO_BANK35 with EVB_VDDIO_BANK13 ('''requirerd when TRACE is used''')
The following rules must be observed:
* Because of a hardware limitation, VDDIO_BANK35 '''must be configured for 3.3V power supply (Jumper on 1-2)'''.
* The configuration 1. (Jumper on 1-2) excludes 2. (Jumper on 3-4) (and viceversa)
* The configuration 3. (Jumper on 5-6) excludes 4. (Jumper on 7-8) (and viceversa)
The DEFAULT configuration is:
* Jumper on 1-2 ('''please note that this jumper must not be removed''')
* Jumper on 5-6
<section end=Power Supply/>
<section begin=Reset button/>
|}
<section end=Ethernet1/>
<section begin=JTAG/>
=== JTAG ===
