Physical devices mapping (XUELK)

Info Box Applies to SBC Lynx

This article details how physical devices are mapped to Linux device files in the context of the XUELK kit.

Console UART

Physical device	Processor's resource	Connector	Type	Linux device file	Notes
Boot Console	UART1	J42	2-wire LVTTL UART	/dev/ttymxc0

Multi-protocol UARTs

Ordering code: XUBxx0xxx0x

Physical device	Processor's resource	Connector	Type	Linux device file	Notes
MPUART0	UART7	J34	2-wire RS232	/dev/ttymxc6
MPUART1	UART3	J21	RS485	/dev/ttymxc2

Ordering code: XUBxx0xxx1x

Physical device	Processor's resource	Connector	Type	Linux device file	Notes
MPUART0	UART8	J34	2-wire RS232	/dev/ttymxc7
MPUART1	UART3	J21	RS485	/dev/ttymxc2

UART2 on mezzanine connector J53

Please note that this UART is not available if WiFi/Bluetooth module is populated.

Processor's resource	Connector	Type	Linux device file	Notes
UART2	J53	4-wire LVTTL	/dev/ttymxc1

Ethernet

Ethernet port is associated to eth0 interface. It can be managed with standard Linux commands. See for example http://www.tecmint.com/ifconfig-command-examples/.

GPIOs on mezzanine connector J53

Processor's resource	Connector	Type	Linux virtual resource	Notes
MX6UL_PAD_UART5_RX_DATA__GPIO1_IO31	J53	LVTTL GPIO	GPIO #31	see following examples
MX6UL_PAD_UART5_TX_DATA__GPIO1_IO30	J53	LVTTL GPIO	GPIO #30	see following examples
MX6UL_PAD_LCD_DATA19__GPIO3_IO24	J53	LVTTL GPIO	GPIO #24	see following examples
MX6UL_PAD_LCD_DATA22__GPIO3_IO27	J53	LVTTL GPIO	GPIO #27	see following examples
MX6UL_PAD_LCD_DATA23__GPIO3_IO28	J53	LVTTL GPIO	GPIO #28	see following examples

Example #1

The following commands can be issued from command line in order to configure GPIO #30 as output:

echo 30 > /sys/class/gpio/export
echo out > /sys/class/gpio/gpio30/direction

To set the GPIO #30 to 0 logical value:

echo 0 > /sys/class/gpio/gpio30/value

To set the GPIO #30 to 1 logical value:

echo 1 > /sys/class/gpio/gpio30/value

Example #2

The following commands can be issued from command line in order to configure GPIO #30 as input:

echo 30 > /sys/class/gpio/export
echo in > /sys/class/gpio/gpio30/direction

To read the GPIO value:

cat /sys/class/gpio/gpio$i/value

microSD card

microSD card, if present, will be associated by the Linux kernel to the mmcblk0 device:

mmc0: host does not support reading read-only switch. assuming write-enable.
mmc0: new high speed SDHC card at address e624
mmcblk0: mmc0:e624 SU08G 7.40 GiB
 mmcblk0: p1
FAT-fs (mmcblk0p1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.

Once detected, it can be mounted and accessed via usual Linux commands:

root@sbc-lynx:~# mount /dev/mmcblk0p1 /mnt/mmcblk0p1/
root@sbc-lynx:~# time cp VirtualBox-5.0.14-105127-Win.exe /mnt/mmcblk0p1/

real    0m14.274s
user    0m0.020s
sys     0m4.640s
root@sbc-lynx:~# ls -la /mnt/mmcblk0p1/
total 114452
drwxrwx--- 3 root disk      4096 Apr  1 19:52 .
drwxr-xr-x 7 root root      4096 Jul 22  2016 ..
drwxrwx--- 2 root disk      4096 Jul 22  2016 System Volume Information
-rwxrwx--- 1 root disk 117185736 Apr  1 19:52 VirtualBox-5.0.14-105127-Win.exe
root@sbc-lynx:~# umount /mnt/mmcblk0p1/

WiFi/Bluetooth

Please refer to this page.