Bureaucrats, dave_user, Administrators
8,226
edits
Changes
→Layout
{{InfoBoxTop}}
{{Applies To Diva}}
{{InfoBoxBottom}}
==Introduction==
DivaEVB-Lite is a carrier board designed to host [[Diva SOM|Diva system-on-module]]. It can also act as an adaptation board used in combination with [[:Category:Dacu|Dacu]] carrier board. Therefore two different versions exist that are a little bit different.
=== DivaEVB-Lite Standalone version ===
[[File:Diva-evb-01.png|300px|frameless|border]]
The following picture shows Diva-EVB-Lite's block diagram when configured as standalone carrier board:
[[File:Divaevb-lite-bd.png|500px|frameless|border]]
=== DivaEVB-Lite for Dacu ===
[[File:Divaevb-divelk 01.png|300px|frameless|border]]
{{ImportantMessage|text=When used in combination with [[:Category:Dacu|Dacu]], please note the points listed below: }}
* the following parts are not installed because their respective functionality is already implemented on DACU board
** USBOTG port
** RS232 UART port
** PSU.
* some wired connections are necessary; these are detailed in the [[#Schematics|Schematics]] section.
* on J18 connector, a jumper must be placed on positions 1-2 and 3-4
Please see also [[Dacu for the Diva SOM]].
[[File:Divelk 03.png|500px]]
==Booting options==
Diva module is built upon AM335x processor. This component supports several booting options that are summarized [[Hardware_Manual_(Diva)#Boot_Options|here]]. Reading of that section is recommended for understanding this document.
In general, AM335x ROM code creates a booting device list that are scanned for searching an available booting image.
===Available options===
Boot modes can be selected by S3 switches which acts directly on SYSBOOT configuration pins.
S3 switches are mapped to SYBOOT[3:0] pins allowing different boot modes.
{|class="wikitable" style="text-align: center;"
|-
!S3 switch
!SYSBOOT pin
|-
| S3.5 || SYSBOOT3
|-
| S3.6 || SYSBOOT2
|-
| S3.7 || SYSBOOT1
|-
| S3.8 || SYSBOOT0
|}
<b>N.B.</b> bit set to 0 means DIP SWITCH has to be set to ON position.
==== Boot from NOR example ====
* SYSBOOT[3:0] = 0111 set S3[5:8] switches to ON-OFF-OFF-OFF
[[File: Sysboot.png | 400px]]
Same example can be found in the following table:
{|class="wikitable" style=Introduction=="text-align: center;"DivaEVB|-Lite is an adapter board designed to evaluate the functionalities of !SYBOOT[[Diva SOM3:0]!Boot sequence!Notes|-| 0111|| MMC0/SPI0/UART0 ||'''Default''' boot from NOR SPI|-| 0011|| NAND/NANDI2C/MMC0||boot from NAND|Diva system-| 1001|| SPI0/MMC0/EMAC1||boot from EMAC if DIVA has no NOR and no NAND onboard|-module]]. |}
{{ImportantMessage|text=Please note that Orcad CIS is required to get all the information about BOM variants included in .dsn files.
PDF files show statically the view of the default BOM variant variants used to manufacture different versions of the board(if any). Components that are not populated are denoted as "Do Not Stuff".}}* OrcadORCAD: coming soonhttp://mirror.dave.eu/diva/schematics/divaevb-lite-1.0.3-DIVELK-dsn.zip* PDF** DivaEVB-Lite for DACU: http://mirror.dave.eu/diva/schematics//divaevb-lite-1.0.3-S.EVBDL1000C.1.0.3.pdf** DivaEVB-Lite standalone: http: coming soon//mirror.dave.eu/diva/schematics//divaevb-lite-1.0.3-S.EVBDL0000C.1.0.0.pdf
==BOM==
* coming soonDivaEVB-Lite for DACU: http://mirror.dave.eu/diva/schematics//divaevb-lite_BOM_S-EVBDL1000C-1.0.3.csv_.zip
==Layout==
* http://mirror.dave.eu/diva/schematics//divaevb-lite-CS143112A_component_view.pdf
==Mechanical==
* DXF: coming soonhttp://mirror.dave.eu/diva/mechanicals/divaevb-lite_2D_CS143112A.zip* IDF(3D): http: coming soon//mirror.dave.eu/diva/mechanicals/divaevb-lite_3D_CS143112A.zip