Deploying Embedded Linux Systems

Info Box Applies to Linux

Introduction

Deployment of Embedded Linux systems is the typical operation which follows the development phase. When the application is ready and fully tested in the develoment environment, it's time to take the system to the field for the “real work”. This phase brings a lot of concerns to cope with, for example creating a suitable root filesystem, saving the data properly, implement successful on-the-field update strategies. This how-to guide explains how to solve the problems connected to the deployment of an embedded linux system.

The development environment

The following figure illustrates the typical developing environment for an Embedded Linux system: it is composed by a host machine and a target machine.

The host (usually a PC or a virtual machine running the Linux operating system) is used by the developer to (cross-)compile the code that will run on the target, for example a Dave ARM CPU module such as Lizard or Naon. The Linux kernel running on the target is able to mount the root file system from different physical media. During the software development, it is very common to use a directory exported via NFS by the host for this purpose. Moreover, the linux kernel is usually retrieved by a simple network transfer protocol like tftp.

Moving to the field

When the system is ready to move to the field, most of the times the particular link between host and target must be removed. In the worst case, the system must run without any NFS filesystem or file transfer services, relying only on its hardware resources (for example, the on-board ram and flash memories). Resources that are obviously limited, due to the nature of the embedded systems. Generally speaking, the procedure used to deploy the system configuration highly depends on the specific application; however, some topics are quite common. The following sections shine a light on these topics.

Root file systems

Linux needs a root file system: a root file system must contain everything needed to support the Linux system (applications, settings, data, ..). The root file system is the file system that is contained on the same partition on which the root directory is located. The Linux kernel, at the end of its startup stage, mounts the root file system on the configured root device and finally launches the /sbin/init, the first user space process and "father" of all the other processes. An example of root file system is shown below:

drwxr-xr-x  2 root     root     4096 2011-05-03 11:23 bin/
drwxr-xr-x  2 root     root     4096 2011-04-01 17:20 boot/
drwxr-xr-x  3 root     root     4096 2011-07-07 12:17 dev/
drwxr-xr-x 44 root     root     4096 2011-05-03 19:02 etc/
drwxr-xr-x  4 root     root     4096 2011-04-01 17:35 home/
drwxr-xr-x  5 root     root     4096 2011-05-03 11:23 lib/
drwxr-xr-x 12 root     root     4096 2011-07-07 12:03 media/
drwxr-xr-x  6 root     root     4096 2011-05-19 16:39 mnt/
drwxr-xr-x  2 root     root     4096 2011-03-11 05:21 proc/
drwxr-xr-x  2 root     root     4096 2011-05-03 11:23 sbin/
drwxr-xr-x  2 root     root     4096 2011-03-11 05:21 sys/
lrwxrwxrwx  1 root     root        8 2011-05-30 12:19 tmp -> /var/tmp/
drwxr-xr-x 11 root     root     4096 2010-11-05 19:36 usr/
drwxr-xr-x  8 root     root     4096 2010-12-12 11:30 var/

Strategies

The integrity of the root file system is mandatory to allow the kernel to complete the boot process and usually it is not required that the whole file system is writeable. For these reasons, usually the file system is splitted in (at least) two parts as shown in the following table:

Part	File System type	Access	Physical medium
Minimal root file system	ext2, cramfs, ..	write protected	ramdisk (*)
Storage file system	UBIFS, JFFS2, YAFFS2, ext2/3, ..	read/write	NOR and NAND flashes, SSD, hard disk, ..

(*) As this file system is mounted over a volatile memory, modifications will be lost when the system will be turned off.

The first part is the actual root file system, it contains the minimum components to allow the system to boot properly and usually it does not require on-the-field upgrading. The other part is used to store applications binaries and files created and/or modified by the user, thus it must be mounted over a non-volatile memory device.

Creating the root file system

Building a root file system from scratch is definitively a complex task because several well known directories must be created and populated with a lot of files that must follow some standard rules. Usually, it's a good idea to start with a pre-packaged root file system, in order to skip the actual creation step, and letting you to work on the customization of the file system.

If you want to build a root file system, there are several possibilities that are described in the following sections.

OpenEmbedded

OpenEmbedded is a build framework for Embedded Linux. It offers a cross-compile environment which allows developers to create a complete Linux Distribution for embedded systems. Some of the OpenEmbedded advantages include:

• support for many hardware architectures
• multiple releases for those architectures
• tools for speeding up the process of recreating the base after changes have been made
• easy to customize
• runs on any Linux distribution
• cross-compiles 1000's of packages including GTK+, Qt, the X Windows system, Mono, Java, ...

OpenEmbedded is at the basis of some known distribution, like Angstrom, OpenMoko and Poky and it can target a lot of different targets and architectures. Primarily, the project maintains and develops a collection of BitBake (a task execution manager derived from Gentoo's Portage) recipes The recipes consist of the source URL of the package, dependencies and compile or install options. During the build process they are used to track dependencies, cross-compile the package and pack it up, suitable to be installed on the target device. It's also possible to create complete images, consisting of root file system and kernel. As a first step the framework will build a cross-compiler toolchain for the target platform, then the build system builds all the packages included in the selected BitBake recipe, which can range from a single application to an entire Linux distribution.

Arago

Arago Project targets the TI OMAP, Sitara and DaVinci platform, providing a verified, tested and supported subset of packages and has been created to simplify the standard OpenEmbedded approach (mainly setup and interaction). In fact, setting up a complete OE/Bitbake system is a task recommended only to experienced users/developers, so the availability of a SDK that allows building applications for the target without learning OE/Bitbake is very important for the less-experienced audience.