Difference between revisions of "Enabling SPI1 and SPI3 on Linux (Naon)"

From DAVE Developer's Wiki
Jump to: navigation, search
(fix wrong closing tag)
m
(10 intermediate revisions by 2 users not shown)
Line 1: Line 1:
 
{{InfoBoxTop}}
 
{{InfoBoxTop}}
 
{{AppliesToNaon}}
 
{{AppliesToNaon}}
−
{{Applies To NaonEVB-Mid}}
 
 
{{Applies To Linux}}
 
{{Applies To Linux}}
 
{{InfoBoxBottom}}
 
{{InfoBoxBottom}}
Line 7: Line 6:
 
=== Introduction ===
 
=== Introduction ===
  
−
This article shows how to enable the SPI1 and SPI3 (with CS1 chip select) interfaces which can be used in a standard Linux application.
+
This article shows how to enable the SPI1 and SPI3 interfaces which can be used in a standard Linux application.
  
 
=== Pin Mux Option ===
 
=== Pin Mux Option ===
  
−
SPI signals are available at different Naon pins. '''The configuration described below is dedicated to the NaonEVB-Mid carrier board''', which provides the SPI1 and SPI3 signals at the '''J21''' connector (please refer to [[NaonEVB-Mid | NaonEVB-Mid wiki page]] for further details).
+
SPI1 signals are available at different Naon pins. The following configuration can be used:
−
 
 
−
The following is the pin multiplexing configuration:
 
  
 +
==== Option 1 ====
 
{|class="wikitable" style="text-align:right"  
 
{|class="wikitable" style="text-align:right"  
 
!Signal
 
!Signal
Line 20: Line 18:
 
!CPU Ball
 
!CPU Ball
 
|-
 
|-
−
|SPI1_SCLK
+
|
−
|J1.34
+
|
−
|AC3
+
|
 
|-
 
|-
−
|SPI1_SCS1n
+
|
−
|J2.112
+
|
−
|W6
+
|
 
|-
 
|-
−
|SPI1_D0
+
|
−
|J1.37
+
|
−
|AA6
+
|
 
|-
 
|-
−
|SPI1_D1
+
|
−
|J1.90
+
|
−
|AA3
+
|
 
|-
 
|-
 
|
 
|
 
|
 
|
 
|
 
|
−
|-
 
−
|SPI3_SCLK
 
−
|J2.99
 
−
|AC26
 
−
|-
 
−
|SPI3_SCS1n
 
−
|J2.111
 
−
|AG27
 
−
|-
 
−
|SPI3_D0
 
−
|J2.89
 
−
|V22
 
−
|-
 
−
|SPI3_D1
 
−
|J2.87
 
−
|AA25
 
 
|}
 
|}
  
−
=== U-Boot patch ===
+
=== U-Boot patches ===
  
 
{{ImportantMessage|text=The patches below applies to NELK 4.0.0 and above U-Boot source tree.}}
 
{{ImportantMessage|text=The patches below applies to NELK 4.0.0 and above U-Boot source tree.}}
  
  
−
The files <code>board/dave/naon/pinmux_evb_mid.h</code> must be modified according to the following patch:
+
The files <code>arch/arm/mach-omap2/board-diva.c</code> and <code>arch/arm/mach-omap2/diva_pinmux_table.h</code> must be modified according to the following patches:
  
−
<syntaxhighlight lang="diff">
+
<diff>
−
diff --git a/board/dave/naon/pinmux_evb_mid.h b/board/dave/naon/pinmux_evb_mid.h
+
</diff>
−
index ae21ca3..df3783f 100644
 
−
--- a/board/dave/naon/pinmux_evb_mid.h
 
−
+++ b/board/dave/naon/pinmux_evb_mid.h
 
−
@@ -45,7 +45,7 @@ MUX_VAL(PINCNTL3, (IEN | IPU | FCN1 )) /* SD1_DAT[0] */\
 
−
MUX_VAL(PINCNTL4, (IEN | IPU | FCN1 )) /* SD1_DAT[1]_SDIRQ */\
 
−
MUX_VAL(PINCNTL5, (IEN | IPU | FCN1 )) /* SD1_DAT[2]_SDRW */\
 
−
MUX_VAL(PINCNTL6, (IEN | IPU | FCN1 )) /* SD1_DAT[3] */\
 
−
-MUX_VAL(PINCNTL7, (IEN | IPU | DISABLED )) /* safe_mode */\
 
−
+MUX_VAL(PINCNTL7, (IEN | IPU | FCN2 )) /* SPI[1]_SCS[1] */\
 
−
MUX_VAL(PINCNTL8, (IEN | IPU | FCN1 )) /* SD0_CLK */\
 
−
MUX_VAL(PINCNTL9, (IEN | IPU | FCN1 )) /* SD0_CMD */\
 
−
MUX_VAL(PINCNTL10, (IEN | IPU | FCN1 )) /* SD0_DAT[0] */\
 
−
@@ -258,10 +258,10 @@ MUX_VAL(PINCNTL218, (IEN | IPD | DISABLED )) /* safe_mode */\
 
−
MUX_VAL(PINCNTL219, (IEN | IPD | DISABLED )) /* safe_mode */\
 
−
MUX_VAL(PINCNTL220, (IEN | IPD | DISABLED )) /* safe_mode */\
 
−
MUX_VAL(PINCNTL221, (IEN | IPD | DISABLED )) /* safe_mode */\
 
−
-MUX_VAL(PINCNTL222, (IEN | IPD | DISABLED )) /* safe_mode */\
 
−
-MUX_VAL(PINCNTL223, (IEN | IPD | DISABLED )) /* safe_mode */\
 
−
-MUX_VAL(PINCNTL224, (IEN | IPD | DISABLED )) /* safe_mode */\
 
−
-MUX_VAL(PINCNTL225, (IEN | IPD | DISABLED )) /* safe_mode */\
 
−
+MUX_VAL(PINCNTL222, (IEN | IPU | FCN6 )) /* SPI[3]_SCS[1] */\
 
−
+MUX_VAL(PINCNTL223, (IEN | DIS | FCN6 )) /* SPI[3]_SCLK_MUX1 */\
 
−
+MUX_VAL(PINCNTL224, (IEN | DIS | FCN6 )) /* SPI[3]_D[1]_MUX1 */\
 
−
+MUX_VAL(PINCNTL225, (IEN | DIS | FCN6 )) /* SPI[3]_D[0]_MUX1 */\
 
−
MUX_VAL(PINCNTL226, (IEN | IPD | DISABLED )) /* safe_mode */\
 
−
MUX_VAL(PINCNTL227, (IEN | IPD | DISABLED )) /* safe_mode */\
 
−
MUX_VAL(PINCNTL228, (IEN | IPU | FCN7 )) /* I2C[2]_SCL_MUX2 */\
 
−
</syntaxhighlight>
 
  
 
U-Boot must be rebuilt to make these modifications effective.
 
U-Boot must be rebuilt to make these modifications effective.
  
−
=== Linux kernel patch ===
+
 
 +
 
 +
=== Linux kernel patches ===
  
 
{{ImportantMessage|text=The patches below applies to NELK 4.0.0 and above Linux source tree.}}
 
{{ImportantMessage|text=The patches below applies to NELK 4.0.0 and above Linux source tree.}}
  
  
−
The files <code>arch/arm/mach-omap2/board-naon.c</code> and <code>drivers/spi/omap2_mcspi.c</code> must be modified according to the following patch:
+
The files <code>arch/arm/mach-omap2/board-diva.c</code> and <code>arch/arm/mach-omap2/diva_pinmux_table.h</code> must be modified according to the following patches:
  
 
<diff>
 
<diff>
−
diff --git a/arch/arm/mach-omap2/board-naon.c b/arch/arm/mach-omap2/board-naon.c
 
−
index 683af8e..e9d5023 100644
 
−
--- a/arch/arm/mach-omap2/board-naon.c
 
−
+++ b/arch/arm/mach-omap2/board-naon.c
 
−
@@ -794,6 +794,21 @@ struct spi_board_info __initdata naon_spi_slave_info[] = {
 
−
.chip_select = 0,
 
−
},
 
−
#endif
 
−
+
 
−
+        {
 
−
+            .modalias = "spidev",
 
−
+            .mode=SPI_MODE_0,
 
−
+            .max_speed_hz = 2000000,    /* max spiclock (SCK) speed in HZ */
 
−
+            .bus_num = 2,
 
−
+            .chip_select = 1,
 
−
+        },
 
−
+        {
 
−
+            .modalias = "spidev",
 
−
+            .mode=SPI_MODE_0,
 
−
+            .max_speed_hz = 2000000,    /* max spiclock (SCK) speed in HZ */
 
−
+            .bus_num = 4,
 
−
+            .chip_select = 1,
 
−
+        },
 
−
};
 
−
 
−
void __init naon_spi_init(void)
 
−
diff --git a/drivers/spi/omap2_mcspi.c b/drivers/spi/omap2_mcspi.c
 
−
index 06f586e..848a8e7 100644
 
−
--- a/drivers/spi/omap2_mcspi.c
 
−
+++ b/drivers/spi/omap2_mcspi.c
 
−
@@ -1182,7 +1182,7 @@ static int __init omap2_mcspi_probe(struct platform_device *pdev)
 
−
case 4:
 
−
rxdma_id = spi4_rxdma_id;
 
−
txdma_id = spi4_txdma_id;
 
−
- num_chipselect = 1;
 
−
+ num_chipselect = 2;
 
−
break;
 
−
#endif
 
−
default:
 
 
</diff>
 
</diff>
  
−
Please note that SPI bus_num values to be used into the naon_spi_slave_info are:
+
The kernel must be rebuilt to make these modifications effective.
−
 
 
−
* SPI1: .bus_num = 2
 
−
* SPI3: .bus_num = 4
 
  
−
 
−
The kernel must be rebuilt to make these modifications effective.
 
  
 
=== Using the interfaces ===
 
=== Using the interfaces ===
Line 163: Line 75:
 
=== Patch download ===
 
=== Patch download ===
  
−
* U-Boot: [[File:U-boot-nelk-spi1-cs1-spi3-cs1.patch.zip]]
+
* U-Boot:  
−
* Linux: [[File:Linux-nelk-spi1-cs1-spi3-cs1.patch.zip]]
+
* Linux:

Revision as of 09:47, 3 September 2013

HOME SOMs SBCs ToloMEO Embedded Assistant Sale-tag.pngGET A QUOTE Customer-service.pngONLINE HELPDESK
Roadmap IoT Services ML/AI services Embedded Design Services
Info Box
Naon am387x-dm814x.png Applies to Naon
Tux.png Applies to Linux

Introduction[edit | edit source]

This article shows how to enable the SPI1 and SPI3 interfaces which can be used in a standard Linux application.

Pin Mux Option[edit | edit source]

SPI1 signals are available at different Naon pins. The following configuration can be used:

Option 1[edit | edit source]

Signal Naon Connector Phisical Pin CPU Ball

U-Boot patches[edit | edit source]

200px-Emblem-important.svg.png

The patches below applies to NELK 4.0.0 and above U-Boot source tree.


The files arch/arm/mach-omap2/board-diva.c and arch/arm/mach-omap2/diva_pinmux_table.h must be modified according to the following patches:

U-Boot must be rebuilt to make these modifications effective.


Linux kernel patches[edit | edit source]

200px-Emblem-important.svg.png

The patches below applies to NELK 4.0.0 and above Linux source tree.


The files arch/arm/mach-omap2/board-diva.c and arch/arm/mach-omap2/diva_pinmux_table.h must be modified according to the following patches:

The kernel must be rebuilt to make these modifications effective.


Using the interfaces[edit | edit source]

Users can access the peripherals connected to the SP1 and SPI3 buses through the spidev interface. For further information, please refer to

Patch download[edit | edit source]

  • U-Boot:
  • Linux:
HOME SOMs SBCs ToloMEO Embedded Assistant Sale-tag.pngGET A QUOTE Customer-service.pngONLINE HELPDESK
Roadmap IoT Services ML/AI services Embedded Design Services
Retrieved from "https://wiki.dave.eu/index.php?title=Enabling_SPI1_and_SPI3_on_Linux_(Naon)&oldid=2492"