Changes

MISC-TN-004: Running Debian (armbian) on SBCSPG

32,937 bytes added, 10:20, 29 July 2019

no edit summary

==The hardware platform==

From an architectural standpoint, SBCSPG is similar to the [[:Category:SBC_Lynx|SBC Lynx]].

==Creating the root file system==

==Deploying the root file system onto the target==

U-Boot 2016.03-rialto-1.1.2 (Jan 17 2019 - 15:10:28 +0100), Build: jenkins-Rialto_U-Boot-10

CPU: Freescale i.MX6UL rev1.2 528 MHz (running at 396 MHz)

CPU: Industrial temperature grade (-40C to 105C) at 36C

Reset cause: POR

Environment: NAND

I2C: ready

DRAM: 512 MiB

Relocating to 9ff1c000, new gd at 9eefbeb8, sp at 9eefbe90

PMIC: PFUZE3000 DEV_ID=0x30 REV_ID=0x11

NAND: 1024 MiB

MMC: FSL_SDHC: 0

In: serial

Out: serial

Err: serial

switch to partitions #0, OK

mmc0 is current device

SOM ConfigID#: 00000022

SOM UniqueID#: ee6b78bb:1e08a9d4

CB ConfigID#: 00000046

CB UniqueID#: 00000000:00000000

Board: MX6UL Rialto

Net: FEC0

Normal Boot

Hit any key to stop autoboot: 0

=> print net_mmc

net_mmc=run loadk loadfdt mmcargs addip addcons addmisc; if run configid_fixupfdt; then bootm ${loadaddr} - ${fdtaddr}; fi

=> edit mmcroot

edit: /dev/mmcblk0p4 rootwait rw

=> run net_mmc

FEC0 Waiting for PHY auto negotiation to complete...... done

Using FEC0 device

TFTP from server 192.168.0.13; our IP address is 192.168.0.81

Filename 'rialto/linux/rialto-1.1.3_uImage'.

Load address: 0x80800000

Loading: #################################################################

#################################################################

####################################

819.3 KiB/s

done

Bytes transferred = 7170152 (6d6868 hex)

Using FEC0 device

TFTP from server 192.168.0.13; our IP address is 192.168.0.81

Filename 'rialto/linux/rialto-1.1.3_imx6ul-lynx-som0022-cb0046.dtb'.

Load address: 0x83000000

Loading: #######

540 KiB/s

done

Bytes transferred = 33793 (8401 hex)

FDT: override 'som_uniqueid' with 'ee6b78bb:1e08a9d4'

FDT: override 'cb_uniqueid' with '00000000:00000000'

## Booting kernel from Legacy Image at 80800000 ...

Image Name: Linux-4.1.15-rialto-1.1.3

Image Type: ARM Linux Kernel Image (uncompressed)

Data Size: 7170088 Bytes = 6.8 MiB

Load Address: 80008000

Entry Point: 80008000

Verifying Checksum ... OK

## Flattened Device Tree blob at 83000000

Booting using the fdt blob at 0x83000000

FDT: fixup by running configid_fixupfdt..

FDT: override 'som_uniqueid' with 'ee6b78bb:1e08a9d4'

FDT: override 'cb_uniqueid' with '00000000:00000000'

Loading Kernel Image ... OK

reserving fdt memory region: addr=83000000 size=9000

Using Device Tree in place at 83000000, end 8300bfff

Modify /soc/aips-bus@02000000/bee@02044000:status disabled

ft_system_setup for mx6

Starting kernel ...

[ 0.000000] Booting Linux on physical CPU 0x0

[ 0.000000] Linux version 4.1.15-rialto-1.1.3 (jenkins@linuxserver2) (gcc version 5.3.0 (GCC) ) #1 SMP PREEMPT Thu Jul 18 16:19:12 CEST 2019

[ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c53c7d

[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache

[ 0.000000] Machine model: Freescale i.MX6 UltraLite CB0046 SBCSPG rev.A

[ 0.000000] cma: Reserved 64 MiB at 0x9c000000

[ 0.000000] Memory policy: Data cache writealloc

[ 0.000000] PERCPU: Embedded 12 pages/cpu @9bbb1000 s17420 r8192 d23540 u49152

[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048

[ 0.000000] Kernel command line: root=/dev/mmcblk0p4 rootwait rw ip=192.168.0.81:192.168.0.13::255.255.255.0:lynx:eth0:off panic=1 fec_mac=70:b3:d5:3e:a5:72 console=ttymxc0,115200 vmalloc=400M mtdparts=gpmi-nand:8M(nand-uboot),1M(nand-env1),1M(nand-env2),-(nand-ubi);spi0.0:1M(spi-uboot),256k(spi-env1),256k(spi-env2),512k(spi-dtb),8M(spi-kernel),4M(spi-splash),-(spi-free)

[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)

[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)

[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)

[ 0.000000] Memory: 440268K/524288K available (8829K kernel code, 561K rwdata, 3336K rodata, 448K init, 444K bss, 18484K reserved, 65536K cma-reserved, 0K highmem)

[ 0.000000] Virtual kernel memory layout:

[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)

[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB)

[ 0.000000] vmalloc : 0xa0800000 - 0xff000000 (1512 MB)

[ 0.000000] lowmem : 0x80000000 - 0xa0000000 ( 512 MB)

[ 0.000000] pkmap : 0x7fe00000 - 0x80000000 ( 2 MB)

[ 0.000000] modules : 0x7f000000 - 0x7fe00000 ( 14 MB)

[ 0.000000] .text : 0x80008000 - 0x80be9914 (12167 kB)

[ 0.000000] .init : 0x80bea000 - 0x80c5a000 ( 448 kB)

[ 0.000000] .data : 0x80c5a000 - 0x80ce6770 ( 562 kB)

[ 0.000000] .bss : 0x80ce9000 - 0x80d583c0 ( 445 kB)

[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1

[ 0.000000] Preemptible hierarchical RCU implementation.

[ 0.000000] Additional per-CPU info printed with stalls.

[ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=1.

[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1

[ 0.000000] NR_IRQS:16 nr_irqs:16 16

[ 0.000000] mxc_clocksource_init 24000000

[ 0.000000] Switching to timer-based delay loop, resolution 41ns

[ 0.000017] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns

[ 0.000059] clocksource mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns

[ 0.002544] Console: colour dummy device 80x30

[ 0.002586] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000)

[ 0.002619] pid_max: default: 32768 minimum: 301

[ 0.002863] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)

[ 0.002896] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)

[ 0.004269] Initializing cgroup subsys net_cls

[ 0.004358] CPU: Testing write buffer coherency: ok

[ 0.004851] /cpus/cpu@0 missing clock-frequency property

[ 0.004893] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000

[ 0.005007] Setting up static identity map for 0x80008280 - 0x800082d8

[ 0.049002] Brought up 1 CPUs

[ 0.049046] SMP: Total of 1 processors activated (48.00 BogoMIPS).

[ 0.049068] CPU: All CPU(s) started in SVC mode.

[ 0.050199] devtmpfs: initialized

[ 0.072529] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5

[ 0.073449] clocksource jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns

[ 0.078835] pinctrl core: initialized pinctrl subsystem

[ 0.081917] NET: Registered protocol family 16

[ 0.100032] DMA: preallocated 256 KiB pool for atomic coherent allocations

[ 0.130931] cpuidle: using governor ladder

[ 0.161000] cpuidle: using governor menu

[ 0.209331] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.

[ 0.209366] hw-breakpoint: maximum watchpoint size is 8 bytes.

[ 0.213881] imx6ul-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver

[ 0.288772] mxs-dma 1804000.dma-apbh: initialized

[ 0.296632] SCSI subsystem initialized

[ 0.297997] usbcore: registered new interface driver usbfs

[ 0.298237] usbcore: registered new interface driver hub

[ 0.298467] usbcore: registered new device driver usb

[ 0.301170] i2c i2c-0: IMX I2C adapter registered

[ 0.301217] i2c i2c-0: can't use DMA

[ 0.302989] i2c i2c-1: IMX I2C adapter registered

[ 0.303035] i2c i2c-1: can't use DMA

[ 0.303383] Linux video capture interface: v2.00

[ 0.303599] pps_core: LinuxPPS API ver. 1 registered

[ 0.303709] PTP clock support registered

[ 0.306533] MIPI CSI2 driver module loaded

[ 0.307222] Advanced Linux Sound Architecture Driver Initialized.

[ 0.309413] Bluetooth: Core ver 2.20

[ 0.309546] NET: Registered protocol family 31

[ 0.309572] Bluetooth: HCI device and connection manager initialized

[ 0.309615] Bluetooth: HCI socket layer initialized

[ 0.309650] Bluetooth: L2CAP socket layer initialized

[ 0.309768] Bluetooth: SCO socket layer initialized

[ 0.312653] Switched to clocksource mxc_timer1

[ 0.340510] NET: Registered protocol family 2

[ 0.342142] TCP established hash table entries: 4096 (order: 2, 16384 bytes)

[ 0.342281] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)

[ 0.342439] TCP: Hash tables configured (established 4096 bind 4096)

[ 0.342586] UDP hash table entries: 256 (order: 1, 8192 bytes)

[ 0.342772] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)

[ 0.343244] NET: Registered protocol family 1

[ 0.343999] RPC: Registered named UNIX socket transport module.

[ 0.344036] RPC: Registered udp transport module.

[ 0.344059] RPC: Registered tcp transport module.

[ 0.344080] RPC: Registered tcp NFSv4.1 backchannel transport module.

[ 0.347525] imx rpmsg driver is registered.

[ 0.349691] Bus freq driver module loaded

[ 0.351925] futex hash table entries: 256 (order: 2, 16384 bytes)

[ 0.369265] VFS: Disk quotas dquot_6.6.0

[ 0.369761] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)

[ 0.375630] NFS: Registering the id_resolver key type

[ 0.375735] Key type id_resolver registered

[ 0.375759] Key type id_legacy registered

[ 0.375938] jffs2: version 2.2. (NAND) c 2001-2006 Red Hat, Inc.

[ 0.377869] fuse init (API version 7.23)

[ 0.389293] io scheduler noop registered

[ 0.389348] io scheduler deadline registered

[ 0.389863] io scheduler cfq registered (default)

[ 0.391068] imx-weim 21b8000.weim: Driver registered.

[ 0.398506] imx-sdma 20ec000.sdma: no event needs to be remapped

[ 0.398734] imx-sdma 20ec000.sdma: loaded firmware 3.3

[ 0.406952] imx-sdma 20ec000.sdma: initialized

[ 0.408779] pfuze100-regulator 0-0008: Full layer: 1, Metal layer: 1

[ 0.409138] pfuze100-regulator 0-0008: FAB: 0, FIN: 0

[ 0.409169] pfuze100-regulator 0-0008: pfuze3000 found.

[ 0.424445] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 20, base_baud = 5000000) is a IMX

[ 1.097323] console [ttymxc0] enabled

[ 1.103053] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 227, base_baud = 5000000) is a IMX

[ 1.113396] 21ec000.serial: ttymxc2 at MMIO 0x21ec000 (irq = 228, base_baud = 5000000) is a IMX

[ 1.127734] imx sema4 driver is registered.

[ 1.132143] [drm] Initialized drm 1.1.0 20060810

[ 1.138189] [drm] Initialized vivante 1.0.0 20120216 on minor 0

[ 1.170899] brd: module loaded

[ 1.188056] loop: module loaded

[ 1.208198] nand: device found, Manufacturer ID: 0xef, Chip ID: 0xd3

[ 1.214658] nand: Winbond W29N08GV

[ 1.218103] nand: 1024 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64

[ 1.226562] gpmi-nand 1806000.gpmi-nand: mode:4 ,failed in set feature.

[ 1.233293] Scanning device for bad blocks

[ 1.611206] random: nonblocking pool is initialized

[ 2.428559] 4 cmdlinepart partitions found on MTD device gpmi-nand

[ 2.434834] Creating 4 MTD partitions on "gpmi-nand":

[ 2.439935] 0x000000000000-0x000000800000 : "nand-uboot"

[ 2.448168] 0x000000800000-0x000000900000 : "nand-env1"

[ 2.456178] 0x000000900000-0x000000a00000 : "nand-env2"

[ 2.463942] 0x000000a00000-0x000040000000 : "nand-ubi"

[ 2.475077] gpmi-nand 1806000.gpmi-nand: driver registered.

[ 2.484914] tun: Universal TUN/TAP device driver, 1.6

[ 2.496882] CAN device driver interface

[ 2.503831] 20b4000.ethernet supply phy not found, using dummy regulator

[ 3.523866] pps pps0: new PPS source ptp0

[ 3.529200] libphy: fec_enet_mii_bus: probed

[ 3.537969] fec 20b4000.ethernet eth1: registered PHC device 0

[ 3.545824] 2188000.ethernet supply phy not found, using dummy regulator

[ 4.573823] pps pps1: new PPS source ptp1

[ 4.580612] fec 2188000.ethernet eth0: registered PHC device 1

[ 4.588331] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver

[ 4.596062] usbcore: registered new interface driver pegasus

[ 4.601937] usbcore: registered new interface driver rtl8150

[ 4.607869] usbcore: registered new interface driver r8152

[ 4.613664] usbcore: registered new interface driver asix

[ 4.619266] usbcore: registered new interface driver ax88179_178a

[ 4.625610] usbcore: registered new interface driver cdc_ether

[ 4.631654] usbcore: registered new interface driver dm9601

[ 4.637490] usbcore: registered new interface driver sr9700

[ 4.643368] usbcore: registered new interface driver CoreChips

[ 4.649451] usbcore: registered new interface driver smsc75xx

[ 4.655504] usbcore: registered new interface driver smsc95xx

[ 4.661449] usbcore: registered new interface driver net1080

[ 4.667362] usbcore: registered new interface driver plusb

[ 4.673120] usbcore: registered new interface driver cdc_subset

[ 4.679235] usbcore: registered new interface driver zaurus

[ 4.685091] usbcore: registered new interface driver MOSCHIP usb-ethernet driver

[ 4.692878] usbcore: registered new interface driver cdc_ncm

[ 4.698598] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver

[ 4.705271] ehci-mxc: Freescale On-Chip EHCI Host driver

[ 4.711143] usbcore: registered new interface driver usb-storage

[ 4.717659] usbcore: registered new interface driver usbserial

[ 4.723739] usbcore: registered new interface driver usbserial_generic

[ 4.730449] usbserial: USB Serial support registered for generic

[ 4.736731] usbcore: registered new interface driver ftdi_sio

[ 4.742695] usbserial: USB Serial support registered for FTDI USB Serial Device

[ 4.750197] usbcore: registered new interface driver pl2303

[ 4.755981] usbserial: USB Serial support registered for pl2303

[ 4.762105] usbcore: registered new interface driver usb_ehset_test

[ 4.771290] 2184800.usbmisc supply vbus-wakeup not found, using dummy regulator

[ 4.791979] ci_hdrc ci_hdrc.1: EHCI Host Controller

[ 4.797230] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1

[ 4.822738] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00

[ 4.830675] hub 1-0:1.0: USB hub found

[ 4.834774] hub 1-0:1.0: 1 port detected

[ 4.841227] mousedev: PS/2 mouse device common for all mice

[ 4.849333] input: 20cc000.snvs:snvs-powerkey as /devices/platform/soc/2000000.aips-bus/20cc000.snvs/20cc000.snvs:snvs-powerkey/input/input0

[ 4.867491] rtc-m41t80 1-0068: rtc core: registered m41t80 as rtc0

[ 4.877073] snvs_rtc 20cc000.snvs:snvs-rtc-lp: rtc core: registered 20cc000.snvs:snvs-r as rtc1

[ 4.886224] i2c /dev entries driver

[ 4.893551] MIPI DSI driver module loaded

[ 4.898080] MIPI DSI driver module loaded

[ 4.908354] IR NEC protocol handler initialized

[ 4.913032] IR RC5(x/sz) protocol handler initialized

[ 4.918133] IR RC6 protocol handler initialized

[ 4.922818] IR JVC protocol handler initialized

[ 4.927391] IR Sony protocol handler initialized

[ 4.932046] IR SANYO protocol handler initialized

[ 4.937819] IR Sharp protocol handler initialized

[ 4.942578] IR MCE Keyboard/mouse protocol handler initialized

[ 4.948520] IR XMP protocol handler initialized

[ 4.959918] imx2-wdt 20bc000.wdog: timeout 60 sec (nowayout=0)

[ 4.966249] Bluetooth: HCI UART driver ver 2.3

[ 4.970736] Bluetooth: HCI UART protocol H4 registered

[ 4.975974] Bluetooth: HCI UART protocol BCSP registered

[ 4.981317] Bluetooth: HCI UART protocol LL registered

[ 4.986581] Bluetooth: HCI UART protocol ATH3K registered

[ 4.992320] usbcore: registered new interface driver bcm203x

[ 4.998337] usbcore: registered new interface driver btusb

[ 5.004144] usbcore: registered new interface driver ath3k

[ 5.010436] sdhci: Secure Digital Host Controller Interface driver

[ 5.016783] ci_hdrc ci_hdrc.0: there is a vbus glitch

[ 5.021954] sdhci: Copyright(c) Pierre Ossman

[ 5.026462] sdhci-pltfm: SDHCI platform and OF driver helper

[ 5.034061] /soc/aips-bus@02100000/usdhc@02190000: voltage-ranges unspecified

[ 5.041294] sdhci-esdhc-imx 2190000.usdhc: Got CD GPIO

[ 5.047125] sdhci-esdhc-imx 2190000.usdhc: No vmmc regulator found

[ 5.053432] sdhci-esdhc-imx 2190000.usdhc: No vqmmc regulator found

[ 5.104195] mmc0: SDHCI controller on 2190000.usdhc [2190000.usdhc] using ADMA

[ 5.119929] /soc/aips-bus@02100000/usdhc@02194000: voltage-ranges unspecified

[ 5.135751] sdhci-esdhc-imx 2194000.usdhc: No vqmmc regulator found

[ 5.180958] mmc0: host does not support reading read-only switch, assuming write-enable

[ 5.195277] mmc0: new high speed SDHC card at address 0007

[ 5.201798] mmcblk0: mmc0:0007 SD16G 14.5 GiB

[ 5.208784] mmcblk0: p1 p2 p3 p4

[ 5.262803] mmc1: SDHCI controller on 2194000.usdhc [2194000.usdhc] using ADMA

[ 5.288395] leds-pca955x 1-0060: leds-pca955x: Using pca9551 8-bit LED driver at slave address 0x60

[ 5.297629] sdhci-esdhc-imx 2194000.usdhc: card claims to support voltages below defined range

[ 5.314480] leds-pca955x 1-0060: gpios 510...511

[ 5.320320] usbcore: registered new interface driver usbhid

[ 5.326137] usbhid: USB HID core driver

[ 5.346393] mmc1: queuing unknown CIS tuple 0x91 (3 bytes)

[ 5.352058] fsl-asrc 2034000.asrc: driver registered

[ 5.364086] mmc1: new SDIO card at address 0001

[ 5.376681] NET: Registered protocol family 26

[ 5.381226] Netfilter messages via NETLINK v0.30.

[ 5.387621] nfnl_acct: registering with nfnetlink.

[ 5.392569] nf_conntrack version 0.5.0 (7903 buckets, 31612 max)

[ 5.407572] xt_time: kernel timezone is -0000

[ 5.418899] ipt_CLUSTERIP: ClusterIP Version 0.8 loaded successfully

[ 5.430365] Initializing XFRM netlink socket

[ 5.436528] NET: Registered protocol family 10

[ 5.443966] sit: IPv6 over IPv4 tunneling driver

[ 5.450345] NET: Registered protocol family 17

[ 5.455096] NET: Registered protocol family 15

[ 5.459587] can: controller area network core (rev 20120528 abi 9)

[ 5.466032] NET: Registered protocol family 29

[ 5.470530] can: raw protocol (rev 20120528)

[ 5.474900] can: broadcast manager protocol (rev 20120528 t)

[ 5.480622] can: netlink gateway (rev 20130117) max_hops=1

[ 5.486871] Bluetooth: RFCOMM TTY layer initialized

[ 5.491822] Bluetooth: RFCOMM socket layer initialized

[ 5.497255] Bluetooth: RFCOMM ver 1.11

[ 5.501088] Bluetooth: BNEP (Ethernet Emulation) ver 1.3

[ 5.506490] Bluetooth: BNEP filters: protocol multicast

[ 5.511768] Bluetooth: BNEP socket layer initialized

[ 5.516825] Bluetooth: HIDP (Human Interface Emulation) ver 1.2

[ 5.522903] Bluetooth: HIDP socket layer initialized

[ 5.528064] 8021q: 802.1Q VLAN Support v1.8

[ 5.533635] rfkill_gpio bt_rfkill: bt_rfkill device registered.

[ 5.539901] Key type dns_resolver registered

[ 5.569969] imx_thermal 2000000.aips-bus:tempmon: Industrial CPU temperature grade - max:105C critical:100C passive:95C

[ 5.584316] input: gpio-push-button as /devices/platform/gpio-push-button/input/input1

[ 5.593823] rtc-m41t80 1-0068: setting system clock to 2023-01-15 01:40:34 UTC (1673746834)

[ 5.703300] fec 2188000.ethernet eth0: Freescale FEC PHY driver [Micrel KSZ8081 or KSZ8091] (mii_bus:phy_addr=20b4000.ethernet:03, irq=-1)

[ 5.742894] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready

[ 9.703705] fec 2188000.ethernet eth0: Link is Up - 100Mbps/Full - flow control rx/tx

[ 9.723004] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready

[ 9.743630] IP-Config: Complete:

[ 9.746981] device=eth0, hwaddr=70:b3:d5:3e:a5:72, ipaddr=192.168.0.81, mask=255.255.255.0, gw=255.255.255.255

[ 9.758123] host=lynx, domain=, nis-domain=(none)

[ 9.764038] bootserver=192.168.0.13, rootserver=192.168.0.13, rootpath=

[ 9.771180] usb_otg1_vbus: disabling

[ 9.774911] vref-3v3: disabling

[ 9.778410] ALSA device list:

[ 9.781401] No soundcards found.

[ 9.795772] EXT3-fs (mmcblk0p4): error: couldn't mount because of unsupported optional features (240)

[ 9.807057] EXT2-fs (mmcblk0p4): error: couldn't mount because of unsupported optional features (240)

[ 9.858422] EXT4-fs (mmcblk0p4): mounted filesystem with ordered data mode. Opts: (null)

[ 9.866776] VFS: Mounted root (ext4 filesystem) on device 179:4.

[ 9.883176] devtmpfs: mounted

[ 9.887050] Freeing unused kernel memory: 448K (80bea000 - 80c5a000)

[ 10.496160] systemd[1]: systemd 232 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD +IDN)

[ 10.515660] systemd[1]: Detected architecture arm.

Welcome to Debian GNU/Linux 9 (stretch)!

[ 10.554673] systemd[1]: Set hostname to <sbcspg>.

[ 11.418049] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.

[ OK ] Set up automount Arbitrary Executabcrmats File System Automount Point.

[ 11.453950] systemd[1]: Created slice System Slice.

[ OK ] Created slice System Slice.

[ 11.473856] systemd[1]: Created slice system-serial\x2dgetty.slice.

[ OK ] Created slice system-serial\x2dgetty.slice.

[ 11.504257] systemd[1]: Created slice User and Session Slice.

[ OK ] Created slice User and Session Slice.

[ 11.533748] systemd[1]: Listening on Journal Socket (/dev/log).

[ OK ] Listening on Journal Socket (/dev/log).

[ 11.563897] systemd[1]: Started Forward Password Requests to Wall Directory Watch.

[ OK ] Started Forward Password Requests to Wall Directory Watch.

[ 11.593764] systemd[1]: Listening on Journal Socket.

[ OK ] Listening on Journal Socket.

[ 11.631327] systemd[1]: Starting Restore / save the current clock...

Starting Restore / save the current clock...

[ 11.651116] systemd[1]: Listening on udev Kernel Socket.

[ OK ] Listening on udev Kernel Socket.

[ 11.686753] systemd[1]: Starting Nameserver information manager...

Starting Nameserver information manager...

[ 11.704613] systemd[1]: Reached target Swap.

[ OK ] Reached target Swap.

[ 11.718168] systemd[1]: Reached target Remote File Systems.

[ OK ] Reached target Remote File Systems.

[ 11.759789] systemd[1]: Starting Create Static Device Nodes in /dev...

Starting Create Static Device Nodes in /dev...

[ 11.816769] systemd[1]: Mounting Debug File System...

Mounting Debug File System...

[ 11.843132] systemd[1]: dev-hugepages.mount: Couldn't determine result for ConditionVirtualization=!private-users, assuming failed: No such file or directory

[ 11.900340] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe.

[ OK ] Listening on /dev/initctl Compatibility Named Pipe.

[ 11.963804] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.

[ OK ] Started Dispatch Password Requests to Console Directory Watch.

[ 11.993304] systemd[1]: Reached target Paths.

[ OK ] Reached target Paths.

[ 12.013641] systemd[1]: Listening on Syslog Socket.

[ OK ] Listening on Syslog Socket.

[ 12.043481] systemd[1]: Listening on fsck to fsckd communication Socket.

[ OK ] Listening on fsck to fsckd communication Socket.

[ 12.089106] systemd[1]: Starting Load Kernel Modules...

Starting Load Kernel Modules...

[ 12.146983] systemd[1]: Starting Journal Service...

Starting Journal Service...

[ 12.175481] systemd[1]: Starting Remount Root and Kernel File Systems...

Starting Remount Root and Kernel File Systems...

[ 12.233748] systemd[1]: Listening on udev Control Socket.

[ OK ] Listening on udev Control Socket.

[ 12.255885] systemd[1]: Starting Set the console keyboard layout...

Starting Set the console keyboard layout...

[ 12.300492] systemd[1]: Reached target Encrypted Volumes.

[ OK ] Reached target Encrypted Volumes.

[ 12.343277] systemd[1]: Reached target Slices.

[ OK ] Reached target Slices.

[ 12.376923] systemd[1]: Mounted Debug File System.

[ OK ] Mounted Debug File System.

[ 12.401970] systemd[1]: Started Restore / save the current clock.

[ OK ] Started Restore / save the current clock.

[ 12.502408] systemd[1]: Started Create Static Device Nodes in /dev.

[ OK ] Started Create Static Device Nodes in /dev.

[ 12.585921] systemd[1]: Started Load Kernel Modules.

[ OK ] Started Load Kernel Modules.

[ 12.646288] systemd[1]: Started Nameserver information manager.

[ OK ] Started Nameserver information manager.

[ 12.799581] systemd[1]: Mounting FUSE Control File System...

Mounting FUSE Control File System...

[ 12.865084] systemd[1]: Starting Apply Kernel Variables...

Starting Apply Kernel Variables...

[ 12.954008] systemd[1]: Starting udev Kernel Device Manager...

Starting udev Kernel Device Manager...

[ 13.017200] systemd[1]: Mounted FUSE Control File System.

[ OK ] Mounted FUSE Control File System.

[ OK ] Started Apply Kernel Variables.

[ OK ] Started Journal Service.

[ OK ] Started udev Kernel Device Manager.

[ OK ] Started Set the console keyboard layout.

[FAILED] Failed to start Remount Root and Kernel File Systems.

See 'systemctl status systemd-remount-fs.service' for details.

Starting Flush Journal to Persistent Storage...

[ OK ] Reached target Local File Systems (Pre).

Mounting /tmp...

Starting Load/Save Random Seed...

Starting udev Coldplug all Devices...

[ OK ] Mounted /tmp.

[ OK ] Started Load/Save Random Seed.

[ OK ] Reached target Local File Systems.

Starting Armbian ZRAM config...

Starting Set console font and keymap...

Starting Raise network interfaces...

[ OK ] Started Flush Journal to Persistent Storage.

[ OK ] Started Set console font and keymap.

Starting Create Volatile Files and Directories...

[ OK ] Started Create Volatile Files and Directories.

[ OK ] Reached target System Time Synchronized.

Starting Update UTMP about System Boot/Shutdown...

[ OK ] Started Entropy daemon using the HAVEGE algorithm.

[ OK ] Started Update UTMP about System Boot/Shutdown.

[ OK ] Started Armbian ZRAM config.

Starting Armbian memory supported logging...

[ OK ] Started Raise network interfaces.

[ OK ] Started udev Coldplug all Devices.

[ OK ] Found device /dev/ttymxc0.

[ OK ] Listening on Load/Save RF Kill Switch Status /dev/rfkill Watch.

Starting Load/Save RF Kill Switch Status...

[ OK ] Started Load/Save RF Kill Switch Status.

[ OK ] Started Armbian memory supported logging.

[ OK ] Reached target System Initialization.

Starting Armbian hardware optimization...

[ OK ] Started Daily apt download activities.

Starting Armbian hardware monitoring...

[ OK ] Started Daily apt upgrade and clean activities.

[ OK ] Started Daily Cleanup of Temporary Directories.

[ OK ] Reached target Timers.

Starting Armbian filesystem resize...

[ OK ] Listening on D-Bus System Message Bus Socket.

[ OK ] Reached target Sockets.

[ OK ] Started Armbian hardware optimization.

[ OK ] Started Armbian hardware monitoring.

[ OK ] Started Armbian filesystem resize.

[ OK ] Reached target Basic System.

[ OK ] Started Armbian first run tasks.

[ OK ] Created slice system-getty.slice.

[ OK ] Started D-Bus System Message Bus.

Starting Network Manager...

Starting Login Service...

[ OK ] Started Regular background program processing daemon.

Starting LSB: Start/stop sysstat's sadc...

Starting System Logging Service...

Starting LSB: Load kernel modules needed to enable cpufreq scaling...

[ OK ] Started System Logging Service.

[ OK ] Started LSB: Start/stop sysstat's sadc.

[ OK ] Started Login Service.

[ OK ] Started LSB: Load kernel modules needed to enable cpufreq scaling.

Starting LSB: set CPUFreq kernel parameters...

[ OK ] Started Network Manager.

[ OK ] Reached target Network.

Starting OpenBSD Secure Shell server...

[ OK ] Started Unattended Upgrades Shutdown.

Starting Permit User Sessions...

Starting Network Manager Wait Online...

[ OK ] Started LSB: set CPUFreq kernel parameters.

[ OK ] Started Permit User Sessions.

Starting Network Manager Script Dispatcher Service...

Starting LSB: Set sysfs variables from /etc/sysfs.conf...

[ OK ] Started Network Manager Script Dispatcher Service.

[ OK ] Started LSB: Set sysfs variables from /etc/sysfs.conf.

Starting Hostname Service...

[FAILED] Failed to start Hostname Service.

See 'systemctl status systemd-hostnamed.service' for details.

[ OK ] Started OpenBSD Secure Shell server.

[FAILED] Failed to start Network Manager Wait Online.

See 'systemctl status NetworkManager-wait-online.service' for details.

[ OK ] Reached target Network is Online.

Starting LSB: Start NTP daemon...

Starting /etc/rc.local Compatibility...

Starting LSB: Advanced IEEE 802.11 management daemon...

[ OK ] Started LSB: Advanced IEEE 802.11 management daemon.

[ OK ] Started /etc/rc.local Compatibility.

[ OK ] Started Getty on tty1.

[ OK ] Started Serial Getty on ttymxc0.

[ OK ] Reached target Login Prompts.

[ OK ] Started LSB: Start NTP daemon.

[ OK ] Reached target Multi-User System.

[ OK ] Reached target Graphical Interface.

Starting Update UTMP about System Runlevel Changes...

[ OK ] Started Update UTMP about System Runlevel Changes.

Debian Stretch with Armbian Linux ttymxc0

sbcspg login: root

Password:

You are required to change your password immediately (root enforced)

Changing password for root.

(current) UNIX password:

Enter new UNIX password:

Retype new UNIX password:

_

___| |__ ___ ___ _ __ __ _

/ __| '_ \ / __/ __| '_ \ / _` |

\__ \ |_) | (__\__ \ |_) | (_| |

|___/_.__/ \___|___/ .__/ \__, |

|_| |___/

Welcome to Debian Stretch with Armbian Linux 4.1.15-rialto-1.1.3

System load: 0.08 0.07 0.12 Up time: 14 min

Memory usage: 5 % of 494MB IP: 192.168.0.81

CPU temp: 43‹C

Usage of /: 15% of 5.5G

[ General system configuration (beta): armbian-config ]

New to Armbian? Check the documentation first: https://docs.armbian.com

Thank you for choosing Armbian! Support: www.armbian.com

Creating a new user account. Press <Ctrl-C> to abort

Please provide a username (eg. your forename): armbian

Trying to add user armbian

Adding user `armbian' ...

Adding new group `armbian' (1000) ...

Adding new user `armbian' (1000) with group `armbian' ...

Creating home directory `/home/armbian' ...

Copying files from `/etc/skel' ...

Enter new UNIX password:

Retype new UNIX password:

passwd: password updated successfully

Changing the user information for armbian

Enter the new value, or press ENTER for the default

Full Name []:

Room Number []:

Work Phone []:

Home Phone []:

Other []:

Is the information correct? [Y/n]

Dear armbian, your account armbian has been created and is sudo enabled.

Please use this account for your daily work from now on.

root@sbcspg:~#

</pre>

U0001

Bureaucrats, dave_user, Administrators

4,650

edits

Changes

MISC-TN-004: Running Debian (armbian) on SBCSPG

Navigation menu

Personal tools

Namespaces

Variants

Views

More

Search

Navigation

Quick Links

Contact us

How to use wiki

Advanced Search

Tools