customer
235
edits
Changes
→Boot the system
</pre>
from the u-boot console.The following is a dump of the boot messages: <pre>NAON#run net_nfs link up on port 0, speed 100, full duplexUsing cpsw deviceTFTP from server 192.168.0.121; our IP address is 192.168.0.122Filename 'naon/uImage'.Load address: 0x81000000Loading: ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ######doneBytes transferred = 2688116 (290474 hex)## Booting kernel from Legacy Image at 81000000 ... Image Name: Linux-2.6.37-naon-0.2.0 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2688052 Bytes = 2.6 MiB Load Address: 80008000 Entry Point: 80008000 Verifying Checksum ... OK Loading Kernel Image ... OKOK Starting kernel ... Uncompressing Linux... done, booting the kernel.[ 0.000000] Linux version 2.6.37-naon-0.2.0 (nelk@nelk-desktop) (gcc version 4.3.3 (Sourcery G++ Lite 2009q12[ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c53c7f[ 0.000000] CPU: VIPT nonaliasing data cache, VIPT aliasing instruction cache[ 0.000000] Machine: naon[ 0.000000] bootconsole [earlycon0] enabled[ 0.000000] vram size = 48234496 at 0x0[ 0.000000] reserved size = 48234496 at 0x0[ 0.000000] FB: Reserving 48234496 bytes SDRAM for VRAM[ 0.000000] Memory policy: ECC disabled, Data cache writeback[ 0.000000] OMAP chip is TI8148 2.0[ 0.000000] SRAM: Mapped pa 0x40300000 to va 0xfe400000 size: 0x20000[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32928[ 0.000000] Kernel command line: root=/dev/nfs rw nfsroot=192.168.0.121:/home/shared/devel/dave/naon-DAA/sw/0[ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)[ 0.000000] Memory: 130MB = 130MB total[ 0.000000] Memory: 125748k/125748k available, 54476k reserved, 0K highmem[ 0.000000] Virtual kernel memory layout:[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)[ 0.000000] DMA : 0xffc00000 - 0xffe00000 ( 2 MB)[ 0.000000] vmalloc : 0xcb800000 - 0xf8000000 ( 712 MB)[ 0.000000] lowmem : 0xc0000000 - 0xcb000000 ( 176 MB)[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)[ 0.000000] .init : 0xc0008000 - 0xc003b000 ( 204 kB)[ 0.000000] .text : 0xc003b000 - 0xc0514000 (4964 kB)[ 0.000000] .data : 0xc0514000 - 0xc05535a0 ( 254 kB)[ 0.000000] SLUB: Genslabs=11, HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1[ 0.000000] NR_IRQS:375[ 0.000000] omap_hwmod: gpio2: softreset failed (waited 10000 usec)[ 0.000000] omap_hwmod: gpio3: softreset failed (waited 10000 usec)[ 0.000000] omap_hwmod: gpio4: softreset failed (waited 10000 usec)[ 0.000000] IRQ: Found an INTC at 0xfa200000 (revision 5.0) with 128 interrupts[ 0.000000] Total of 128 interrupts on 1 active controller[ 0.000000] GPMC revision 6.0[ 0.000000] Trying to install interrupt handler for IRQ368[ 0.000000] Trying to install interrupt handler for IRQ369[ 0.000000] Trying to install interrupt handler for IRQ370[ 0.000000] Trying to install interrupt handler for IRQ371[ 0.000000] Trying to install interrupt handler for IRQ372[ 0.000000] Trying to install interrupt handler for IRQ373[ 0.000000] Trying to install interrupt handler for IRQ374[ 0.000000] Trying to install type control for IRQ375[ 0.000000] Trying to set irq flags for IRQ375[ 0.000000] OMAP clockevent source: GPTIMER1 at 20000000 Hz[ 0.000000] Console: colour dummy device 80x30[ 0.010000] Calibrating delay loop... 598.01 BogoMIPS (lpj=2990080)[ 0.240000] pid_max: default: 32768 minimum: 301[ 0.240000] Security Framework initialized[ 0.250000] Mount-cache hash table entries: 512[ 0.250000] CPU: Testing write buffer coherency: ok[ 0.260000] devtmpfs: initialized[ 0.260000] regulator: core version 0.5[ 0.270000] regulator: dummy: [ 0.270000] NET: Registered protocol family 16[ 0.280000] OMAP GPIO hardware version 0.1[ 0.280000] OMAP GPIO hardware version 0.1[ 0.280000] OMAP GPIO hardware version 0.1[ 0.290000] OMAP GPIO hardware version 0.1[ 0.300000] registered ti814x_vpss device[ 0.300000] registered TI814x on-chip HDMI device[ 0.310000] Debugfs: Only enabling/disabling deep sleep and wakeup timer is supported now[ 0.330000] bio: create slab <bio-0> at 0[ 0.330000] SCSI subsystem initialized[ 0.340000] usbcore: registered new interface driver usbfs[ 0.340000] usbcore: registered new interface driver hub[ 0.350000] usbcore: registered new device driver usb[ 0.350000] registerd cppi-dma Intr @ IRQ 17[ 0.360000] Cppi41 Init Done[ 0.360000] omap_i2c omap_i2c.1: bus 1 rev4.0 at 100 kHz[ 0.370000] regulator: VRTC: 1800 mV [ 0.370000] regulator: VIO: 1500 mV [ 0.380000] regulator: VDD1: 600 <--> 1500 mV at 1200 mV [ 0.390000] regulator: VDD2: 600 <--> 1500 mV at 1200 mV [ 0.400000] regulator: VDDCTRL: 600 <--> 1400 mV at 1200 mV [ 0.400000] regulator: LDO1: 1100 <--> 3300 mV at 1800 mV [ 0.410000] regulator: LDO2: 1100 <--> 3300 mV at 1800 mV [ 0.420000] regulator: LDO3: 1100 <--> 3300 mV at 3300 mV [ 0.420000] regulator: LDO4: 1100 <--> 3300 mV at 1800 mV [ 0.430000] regulator: LDO5: 1100 <--> 3300 mV at 3300 mV [ 0.440000] regulator: LDO6: 1100 <--> 3300 mV at 3300 mV [ 0.450000] regulator: LDO7: 1100 <--> 3300 mV at 3300 mV [ 0.450000] regulator: LDO8: 1100 <--> 3300 mV at 1800 mV [ 0.460000] tps65910 1-002d: No interrupt support, no core IRQ[ 0.470000] regulator: tps62353: 750 <--> 1537 mV at 1200 mV [ 0.470000] omap_i2c omap_i2c.3: bus 3 rev4.0 at 100 kHz[ 0.500000] omap_i2c omap_i2c.4: bus 4 rev4.0 at 100 kHz[ 0.500000] Advanced Linux Sound Architecture Driver Version 1.0.23.[ 0.510000] Switching to clocksource gp timer[ 0.520000] musb-hdrc: version 6.0, host, debug=0[ 0.520000] musb-hdrc musb-hdrc.0: dma type: dma-cppi41[ 0.530000] musb-hdrc musb-hdrc.0: MUSB HDRC host driver[ 0.530000] musb-hdrc musb-hdrc.0: new USB bus registered, assigned bus number 1[ 0.540000] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002[ 0.550000] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1[ 0.560000] usb usb1: Product: MUSB HDRC host driver[ 0.560000] usb usb1: Manufacturer: Linux 2.6.37-naon-0.2.0 musb-hcd[ 0.570000] usb usb1: SerialNumber: musb-hdrc.0[ 0.570000] hub 1-0:1.0: USB hub found[ 0.580000] hub 1-0:1.0: 1 port detected[ 0.580000] musb-hdrc musb-hdrc.0: USB Host mode controller at cb81e000 using DMA, IRQ 18[ 0.590000] musb-hdrc musb-hdrc.1: dma type: dma-cppi41[ 0.600000] musb-hdrc musb-hdrc.1: MUSB HDRC host driver[ 0.600000] musb-hdrc musb-hdrc.1: new USB bus registered, assigned bus number 2[ 0.610000] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002[ 0.620000] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1[ 0.630000] usb usb2: Product: MUSB HDRC host driver[ 0.630000] usb usb2: Manufacturer: Linux 2.6.37-naon-0.2.0 musb-hcd[ 0.640000] usb usb2: SerialNumber: musb-hdrc.1[ 0.640000] hub 2-0:1.0: USB hub found[ 0.650000] hub 2-0:1.0: 1 port detected[ 0.650000] musb-hdrc musb-hdrc.1: USB Host mode controller at cb828800 using DMA, IRQ 19[ 0.660000] NET: Registered protocol family 2[ 0.670000] IP route cache hash table entries: 2048 (order: 1, 8192 bytes)[ 0.670000] TCP established hash table entries: 8192 (order: 4, 65536 bytes)[ 0.680000] TCP bind hash table entries: 8192 (order: 3, 32768 bytes)[ 0.690000] TCP: Hash tables configured (established 8192 bind 8192)[ 0.690000] TCP reno registered[ 0.700000] UDP hash table entries: 256 (order: 0, 4096 bytes)[ 0.700000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)[ 0.710000] NET: Registered protocol family 1[ 0.720000] RPC: Registered udp transport module.[ 0.720000] RPC: Registered tcp transport module.[ 0.730000] RPC: Registered tcp NFSv4.1 backchannel transport module.[ 0.730000] NetWinder Floating Point Emulator V0.97 (double precision)[ 0.740000] PMU: registered new PMU device of type 0[ 0.750000] omap-iommu omap-iommu.0: ducati registered[ 0.750000] omap-iommu omap-iommu.1: sys registered[ 0.890000] squashfs: version 4.0 (2009/01/31) Phillip Lougher[ 0.900000] JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.[ 0.910000] msgmni has been set to 245[ 0.910000] io scheduler noop registered[ 0.910000] io scheduler deadline registered[ 0.920000] io scheduler cfq registered (default)[ 0.920000] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled[ 0.930000] omap_uart.0: ttyO0 at MMIO 0x48020000 (irq = 72) is a OMAP UART0[ 0.940000] console [ttyO0] enabled, bootconsole disabled[ 0.940000] console [ttyO0] enabled, bootconsole disabled[ 0.950000] omap_uart.1: ttyO1 at MMIO 0x48022000 (irq = 73) is a OMAP UART1[ 0.960000] omap_uart.2: ttyO2 at MMIO 0x48024000 (irq = 74) is a OMAP UART2[ 0.970000] omap_uart.3: ttyO3 at MMIO 0x481a6000 (irq = 44) is a OMAP UART3[ 0.970000] omap_uart.4: ttyO4 at MMIO 0x481a8000 (irq = 45) is a OMAP UART4[ 0.980000] omap_uart.5: ttyO5 at MMIO 0x481aa000 (irq = 46) is a OMAP UART5[ 1.000000] brd: module loaded[ 1.000000] loop: module loaded[ 1.010000] at24 4-0051: 4096 byte 24c32 EEPROM (writable)[ 1.010000] ahci ahci.0: forcing PORTS_IMPL to 0x1[ 1.020000] ahci ahci.0: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode[ 1.030000] ahci ahci.0: flags: ncq sntf pm led clo only pmp pio slum part ccc apst [ 1.040000] scsi0 : ahci_platform[ 1.040000] ata1: SATA max UDMA/133 mmio [mem 0x4a140000-0x4a150fff] port 0x100 irq 16[ 1.050000] mtd_dataflash spi1.0: at45db642d (8192 KBytes) pagesize 1024 bytes, OTP[ 1.060000] Creating 6 MTD partitions on "spi_flash":[ 1.060000] 0x000000000000-0x000000020000 : "SPI u-boot 1st"[ 1.070000] 0x000000020000-0x000000040000 : "SPI u-boot 2nd"[ 1.080000] 0x000000040000-0x000000050000 : "SPI u-boot env1"[ 1.080000] 0x000000050000-0x000000060000 : "SPI u-boot env2"[ 1.090000] 0x000000060000-0x000000360000 : "SPI Linux Kernel"[ 1.100000] usb 2-1: new high speed USB device using musb-hdrc and address 2[ 1.110000] 0x000000360000-0x000000800000 : "SPI Free Space"[ 1.110000] omap2-nand driver initializing[ 1.120000] ONFI flash detected[ 1.120000] ONFI param page 0 valid[ 1.130000] NAND device: Manufacturer ID: 0x2c, Chip ID: 0xd3 (Micron NAND 1GiB 3,3V 8-bit)[ 1.130000] Creating 7 MTD partitions on "omap2-nand.0":[ 1.140000] 0x000000000000-0x000000040000 : "NAND U-Boot-min"[ 1.150000] 0x000000040000-0x000000080000 : "NAND U-Boot"[ 1.150000] 0x000000080000-0x0000000c0000 : "NAND U-Boot Env1"[ 1.160000] 0x0000000c0000-0x000000100000 : "NAND U-Boot Env2"[ 1.170000] 0x000000100000-0x000000380000 : "NAND Kernel"[ 1.180000] 0x000000380000-0x000008280000 : "NAND File System (small)"[ 1.210000] 0x000008280000-0x000040000000 : "NAND File System (big)"[ 1.430000] usb 2-1: New USB device found, idVendor=0424, idProduct=2512[ 1.430000] usb 2-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0[ 1.440000] hub 2-1:1.0: USB hub found[ 1.440000] hub 2-1:1.0: 2 ports detected[ 1.460000] davinci_mdio davinci_mdio.0: davinci mdio revision 1.6[ 1.460000] davinci_mdio davinci_mdio.0: detected phy mask ffffffbd[ 1.470000] davinci_mdio.0: probed[ 1.470000] davinci_mdio davinci_mdio.0: phy[1]: device 0:01, driver Marvell 88E1111[ 1.480000] davinci_mdio davinci_mdio.0: phy[6]: device 0:06, driver SMSC LAN8710/LAN8720[ 1.490000] usbcore: registered new interface driver asix[ 1.500000] usbcore: registered new interface driver cdc_acm[ 1.500000] cdc_acm: v0.26:USB Abstract Control Model driver for USB modems and ISDN adapters[ 1.510000] Initializing USB Mass Storage driver...[ 1.520000] usbcore: registered new interface driver usb-storage[ 1.520000] USB Mass Storage support registered.[ 1.530000] mice: PS/2 mouse device common for all mice[ 1.530000] ata1: SATA link down (SStatus 0 SControl 300)[ 1.540000] input: max7359 as /devices/platform/omap/omap_i2c.4/i2c-4/4-0038/input/input0[ 1.550000] input: TSC2007 Touchscreen as /devices/virtual/input/input1[ 1.560000] omap_rtc omap_rtc: rtc core: registered omap_rtc as rtc0[ 1.570000] i2c /dev entries driver[ 1.570000] Driver for 1-wire Dallas network protocol.[ 1.730000] ina219 3-0041: hwmon1: sensor 'ina219'[ 1.790000] OMAP Watchdog Timer Rev 0x00: initial timeout 60 sec[ 1.810000] usbcore: registered new interface driver usbhid[ 1.810000] usbhid: USB HID core driver[ 1.820000] notify_init : notify drivercreated for remote proc id 2 at physical Address 0xbf900000[ 1.830000] ALSA device list:[ 1.830000] No soundcards found.[ 1.830000] TCP cubic registered[ 1.840000] NET: Registered protocol family 17[ 1.840000] Registering the dns_resolver key type[ 1.850000] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3[ 1.860000] Power Management for TI81XX.[ 1.870000] Detected MACID=d4:94:a1:8e:68:24[ 1.870000] omap_rtc omap_rtc: setting system clock to 2000-01-01 00:00:00 UTC (946684800)[ 2.390000] [ 2.390000] CPSW phy found : id is : 0x7c0f1[ 2.400000] [ 2.400000] CPSW phy found : id is : 0x1410cc2[ 3.420000] IP-Config: Complete:[ 3.420000] device=eth0, addr=192.168.0.122, mask=255.255.255.0, gw=192.168.0.254,[ 3.430000] host=naon, domain=, nis-domain=(none),[ 3.430000] bootserver=192.168.0.121, rootserver=192.168.0.121, rootpath=[ 4.390000] PHY: 0:01 - Link is Up - 0/Half[ 4.400000] PHY: 0:01 - Link is Down[ 5.390000] PHY: 0:06 - Link is Up - 100/Full[ 5.400000] VFS: Mounted root (nfs filesystem) on device 0:14.[ 5.410000] devtmpfs: mounted[ 5.410000] Freeing init memory: 204KINIT: version 2.86 bootingPlease wait: booting...Error opening /dev/fb0: No such file or directoryStarting udev[ 6.170000] udevd (87): /proc/87/oom_adj is deprecated, please use /proc/87/oom_score_adj instead.Root filesystem already rw, not remountingCaching udev devnodes[ 11.440000] NET: Registered protocol family 10ALSA: Restoring mixer settings.../usr/sbin/alsactl: load_state:1625: No soundcards found...NOT configuring network interfaces: / is an NFS mountFri Dec 9 18:54:00 UTC 2011INIT: Entering runlevel: 5DM814X prcm_config_app version: 2.0.0.1Doing PRCM settings... PRCM for IVHD0 is in Progress, Please wait..... BW Phy Addr : 0x48180600 Data : 0x00000001 AW Phy Addr : 0x48180600 Data : 0x00000002 Phy Addr : 0x48180c04 Data : 0x00000037 BW Phy Addr : 0x48180620 Data : 0x00070000 AW Phy Addr : 0x48180620 Data : 0x00070002 BW Phy Addr : 0x48180624 Data : 0x00030000 AW Phy Addr : 0x48180624 Data : 0x00010002 Phy Addr : 0x48180600 Data : 0x00000102 BW Phy Addr : 0x48180c10 Data : 0x00000007 AW Phy Addr : 0x48180c10 Data : 0x00000003 Phy Addr : 0x48180c14 Data : 0x00000004 BW Phy Addr : 0x58088000 Data : 0xeafffffe AW Phy Addr : 0x58088000 Data : 0xeafffffe BW Phy Addr : 0x58098000 Data : 0xeafffffe AW Phy Addr : 0x58098000 Data : 0xeafffffe BW Phy Addr : 0x48180c10 Data : 0x00000003 AW Phy Addr : 0x48180c10 Data : 0x00000000 Phy Addr : 0x48180c14 Data : 0x00000007 PRCM for IVHD0 is Done Successfully PRCM Initialization completed Loading syslink module[ 12.870000] SysLink version : 2.00.05.85[ 12.870000] SysLink module created on Date:Feb 3 2012 Time:16:15:09Loading HDVICP2 FirmwareMemCfg: DCMM (Dynamically Configurable Memory Map) Version : 2.1.1.1FIRMWARE: Memory Configuration status : In ProgressFIRMWARE: 1 start SuccessfulLoading HDVPSS FirmwareMemCfg: DCMM (Dynamically Configurable Memory Map) Version : 2.1.1.1FIRMWARE: Memory Configuration status : In ProgressFIRMWARE: 2 start Successful[ 15.420000] HDMI W1 rev 4.0Starting system message bus: dbus.Starting telnet daemon.Starting syslogd/klogd: doneStarting thttpd.Starting PVR[ 17.870000] [drm] Initialized drm 1.1.0 20060810[ 18.210000] [drm] Initialized pvrsrvkm 1.7.783851 Thu May 24 CEST 2012 for SGX on minor 0FATAL: Module omaplfb not found.FATAL: Module bufferclass_ti not found.BusyBox v1.13.2 (2011-12-09 14:43:32 IST) multi-call binary Usage: mknod [OPTIONS] NAME TYPE MAJOR MINOR Create a special file (block, character, or pipe) Options: -m Create the special file using the specified mode (default a=rw)TYPEs include: b: Make a block device c or u: Make a character device p: Make a named pipe (MAJOR and MINOR are ignored) chmod: /dev/pvrsrvkm: No such file or directory/dev/mem opened.Memory mapped at address 0x400b3000.Read at address 0x48180F04 (0x400b3f04): 0x00000001Write at address 0x48180F04 (0x400b3f04): 0x00000000, readback 0x00000000/dev/mem opened.Memory mapped at address 0x4023d000.Read at address 0x48180900 (0x4023d900): 0x00000102Write at address 0x48180900 (0x4023d900): 0x00000002, readback 0x00000002/dev/mem opened.Memory mapped at address 0x40139000.Read at address 0x48180920 (0x40139920): 0x00040002Write at address 0x48180920 (0x40139920): 0x00000002, readback 0x00000002 _____ _____ _ _ | _ |___ ___ ___ ___ | _ |___ ___ |_|___ ___| |_ | | _| .'| . | . | | __| _| . | | | -_| _| _||__|__|_| |__,|_ |___| |__| |_| |___|_| |___|___|_| |___| |___| Arago Project http://arago-project.org dm814x-evm ttyO0 Arago 2011.09 dm814x-evm ttyO0 dm814x-evm login:</pre>
