DESK-MX-L-AN-0007: Getting Started With QT Creator

Info Box Applies to AXEL Lite Application Notes

This application note was validated against specific versions of the kit only. It may not work with other versions. Supported versions are listed in the History section.

Contents

HistoryEdit

Page version	Date	XELK version	Notes
1.0.0	March 2018	XELK 3.0.0	First release
2.0.0	August 2019	XELK 4.0.0	Updated XELK version
3.0.0	August 2022	DESK-MX6-L 1.0.0	DESK-MX6-L version

IntroductionEdit

This application note details QT Creator setup and configuration in DESK-MX6-L MVM

Setting up Qt Creator to build for DESK-MX6-LEdit

Note: The version of Qt Creator may differ from images below. The version used is the release is 4.4.1 which can be downloaded form Qt archive server

Qt Creator InstallationEdit

To install Qt Creator inside your toolchain launch a terminal emulator and run

dvdk@vagrant:~$ cd desk-mx-l/

dvdk@vagrant:~/desk-mx-l$ ./qt-creator-opensource-linux-x86_64-4.4.1.run 

An installation wizard will appear. Clik Next to proced with the installation.

Select Skip.

Select Next.

Select the install directory or click Next.

Select Next.

Click Next again.

And then click Install and complete the installation.

Then Finish to exit the setup wizard.

Manual configurationEdit

If you don't want to use the automatic setup or want to customize the configuration, in this section we details all the step required.

DevicesEdit

Go to Tools -> Options menu:

Select Devices and click Add:

Choose the Generic Linux device:

Insert the IP address of your device, root as username and leave password empty (this is the default configuration of DESK-MX6-L root file systems). Make sure that the device is connected to the network and your virtual machine networking is correctly configured (see this article for more details).

Then click Next:

The device will be created and the connectivity will be tested:

If everything went ok you should see a dialog like the image below.

And finally, this is what the Devices window should look like.

GCC & Cross CompilationEdit

Next you need to configure the cross compilation tool inside Build & Run -> Compiler.

Click Add -> GCC and add the compiler path.

/home/dvdk/desk-mx-l/sdk/latest_desk-mx6-l/sysroots/x86_64-pokysdk-linux/usr/bin/arm-poky-linux-gnueabi/arm-poky-linux-gnueabi-gcc

And click Apply.

Do the same for the C++ cross compilation tool.

/home/dvdk/desk-mx-l/sdk/latest_desk-mx6-l/sysroots/x86_64-pokysdk-linux/usr/bin/arm-poky-linux-gnueabi/arm-poky-linux-gnueabi-g++

Debugger GDBEdit

Now it is necessary to add a debugger. In order to do this go to the Debuggers tab and click Add and then select the GDB debugger at the location

/home/dvdk/desk-mx-l/sdk/latest_desk-mx6-l/sysroots/x86_64-pokysdk-linux/usr/bin/arm-poky-linux-gnueabi/arm-poky-linux-gnueabi-gdb

and click Apply.

Qt VersionEdit

Next you need to add the Qt Version installed on your device. Go to Qt Version click Add and select the following qmake file.

/home/dvdk/desk-mx-l/sdk/latest_desk-mx6-l/sysroots/x86_64-pokysdk-linux/usr/bin/qt5/qmake

KitsEdit

The last step is to add a new kit. Go to Kits and click Add and complete the information as shown below. Pay attention that in Qt mkspec you need to write

linux-oe-g++

After this your setup is complete and you can proceed and create your Qt applications.

Qt application exampleEdit

Now that the setup is finished, you can create your first application

Open a new terminal and source the environment variables with the command.

dvdk@vagrant:~/desk-mx-l$ source desk-mx6-l-1.0.0_env.sh

In the same terminal type the following command (we assume you didn't change the default installation directory)

dvdk@vagrant:~$ ./qtcreator-4.4.1/bin/qtcreator

It is important to repeat the previous two steps every time you start QTCreator

Now click on New Project

Select Application Qt Widgets Application and click Choose...

Now call the Project Test and press Next.

Select the SBC AXEL EVK and click Next.

Choose the class name for your application.

Click Finish to conclude the setup.

To add a clickable button to your application, select the Edit window and select Test -> Forms -> mainwindow.ui

Click on Push Button in the Buttons tab and drag it to the main window view. In order to edit the text displayed by the label, double click it and write "Hello World!".

After that, you need to insert the following two line inside the Test.pro file

target.path = /home/root/Test # path on device

INSTALLS += target

Where /home/root/Test is the path in which your application will be downloaded inside the device.

Build the project in order to complete the configuration and set the overall vars:

The last step before running the application inside the device is to configure Qt backend into application command line arguments: open the Project window and select the Run configuration, then type -platform eglfs into Arguments

After these changes you are ready to debug your application inside your board with the Run/Debug command

The debugger (via gdb server) will be activated and the debug window will be ready: