Difference between revisions of "Standalone boot (XELK)"
| Line 12: | Line 12: | ||
!Notes | !Notes | ||
|- | |- | ||
| − | |2.3.1 | + | |{{oldid|7256|2.3.1}} |
|June 2017 | |June 2017 | ||
|[[Axel_Embedded_Linux_Kit_(XELK)#XELK_2.3.1|XELK 2.3.1]] | |[[Axel_Embedded_Linux_Kit_(XELK)#XELK_2.3.1|XELK 2.3.1]] | ||
| Line 18: | Line 18: | ||
| | | | ||
|- | |- | ||
| − | |3.0.1 | + | |{{oldid|7341|3.0.1}} |
|Nov 2017 | |Nov 2017 | ||
|[[Axel_Embedded_Linux_Kit_(XELK)#XELK_3.0.0|XELK 3.0.1]] | |[[Axel_Embedded_Linux_Kit_(XELK)#XELK_3.0.0|XELK 3.0.1]] | ||
Revision as of 07:18, 25 June 2018
| HOME | SOMs | SBCs | ToloMEO Embedded Assistant |  GET A QUOTE
|
 ONLINE HELPDESK
|
| Roadmap | IoT Services | ML/AI services | Embedded Design Services |
Info Box
|
Contents
History[edit | edit source]
| Version | Date | XELK version | Hardware Part Nr | Notes |
|---|---|---|---|---|
| June 2017 | XELK 2.3.1 | XELK 2.0.0 | ||
| Nov 2017 | XELK 3.0.1 | XELK 3.0.1 | ||
| 4.0.0 | July 2018 | XELK 4.0.0 | XELK 4.0.0 |
Introduction[edit | edit source]
This document has been written and tested with the software/hardware combination described in the history table above. However it contains general concept that can be adapted on any DAVE Embedded Systems' Linux platform.
We'll explain how to program and configure a to boot in standalone mode, without the need of a system microSD card or a NFS server, with two options:
- booting with NOR + NAND
- U-Boot will fetch Linux kernel binary images (kernel + device tree) from on-board NOR flash memory, while later the OS will mount the root file system from a NAND partition.
- booting with NAND only
- in this configuration the whole system will boot without the need of a NOR storage, all images and the root file system will be fetch from NAND.
Update u-boot[edit | edit source]
Update to the latest u-boot version allows usage of u-boot environment variables available.
U-Boot > run load
Using FEC device
TFTP from server 192.168.0.13; our IP address is 192.168.0.98
Filename 'axel/u-boot/xelk-2.3.4_mx6qaxel_spi_u-boot.imx'.
Load address: 0x12000000
Loading: #################################################################
##############################################
1.5 MiB/s
done
Bytes transferred = 566184 (8a3a8 hex)
U-Boot > run spi_update
SF: Detected S25FL256S with page size 64 KiB, total 32 MiB
U-Boot >
u-boot on NOR SPI[edit | edit source]
Be sure the spi_update commands has enough erase and program size defined:
U-Boot > setenv spi_update 'sf probe; sf erase 0 90000;sf write ${loadaddr} 400 90000'
Then update u-boot on NOR:
U-Boot > run spi_update SF: Detected S25FL256S with page size 64 KiB, total 32 MiB U-Boot >
u-boot on NAND[edit | edit source]
u-boot on NAND flash must be programmed using NXP kobs-ng utility: this tool is required for writing the correct u-boot image on NAND storing all information needed by bootrom to identify the NAND as a boot device.
Here below an example:
- boot the system via SD on NFS
- uses a rfs with kobs-ng utility available on it (e.g. DAVE's rfs provided with XELK)
- copy the related u-boot imx image file on nfs /home/root (for example)
- execute kobs-ng passing the parameters for flashing u-boot on NAND
root@axel-lite:~# kobs-ng -x -v -w xelk-2.3.4_mx6dlaxel_nand_u-boot.imx
MTD CONFIG:
chip_0_device_path = "/dev/mtd0"
chip_1_device_path = "(null)"
search_exponent = 2
data_setup_time = 80
data_hold_time = 60
address_setup_time = 25
data_sample_time = 6
row_address_size = 3
column_address_size = 2
read_command_code1 = 0
read_command_code2 = 48
boot_stream_major_version = 1
boot_stream_minor_version = 0
boot_stream_sub_version = 0
ncb_version = 3
boot_stream_1_address = 0
boot_stream_2_address = 0
-- We add the 1k-padding to the uboot.
.tmp_kobs_ng: verifying using key '00000000000000000000000000000000'
.tmp_kobs_ng: is a valid bootstream for key '00000000000000000000000000000000'
mtd: opening: "/dev/mtd0"
NFC geometry :
ECC Strength : 8
Page Size in Bytes : 2112
Metadata size : 10
ECC Chunk Size in byte : 512
ECC Chunk count : 4
Block Mark Byte Offset : 1999
Block Mark Bit Offset : 0
====================================================
mtd: opened '/dev/mtd0' - '(null)'
mtd: max_boot_stream_size_in_bytes = 3670016
mtd: boot_stream_size_in_bytes = 564128
mtd: boot_stream_size_in_pages = 276
mtd: #1 0x00100000 - 0x00480000 (0x00189ba0)
mtd: #2 0x00480000 - 0x00800000 (0x00509ba0)
FCB
m_u32Checksum = 0x00000000
m_u32FingerPrint = 0x20424346
m_u32Version = 0x01000000
m_NANDTiming.m_u8DataSetup = 80
m_NANDTiming.m_u8DataHold = 60
m_NANDTiming.m_u8AddressSetup = 25
m_NANDTiming.m_u8DSAMPLE_TIME = 6
m_u32PageDataSize = 2048
m_u32TotalPageSize = 2112
m_u32SectorsPerBlock = 64
m_u32NumberOfNANDs = 0
m_u32TotalInternalDie = 0
m_u32CellType = 0
m_u32EccBlockNEccType = 4
m_u32EccBlock0Size = 512
m_u32EccBlockNSize = 512
m_u32EccBlock0EccType = 4
m_u32MetadataBytes = 10
m_u32NumEccBlocksPerPage = 3
m_u32EccBlockNEccLevelSDK = 0
m_u32EccBlock0SizeSDK = 0
m_u32EccBlockNSizeSDK = 0
m_u32EccBlock0EccLevelSDK = 0
m_u32NumEccBlocksPerPageSDK = 0
m_u32MetadataBytesSDK = 0
m_u32EraseThreshold = 0
m_u32Firmware1_startingPage = 512
m_u32Firmware2_startingPage = 2304
m_u32PagesInFirmware1 = 276
m_u32PagesInFirmware2 = 276
m_u32DBBTSearchAreaStartAddress = 256
m_u32BadBlockMarkerByte = 1999
m_u32BadBlockMarkerStartBit = 0
m_u32BBMarkerPhysicalOffset = 2048
m_u32BCHType = 0
m_NANDTMTiming.m_u32TMTiming2_ReadLatency = 0
m_NANDTMTiming.m_u32TMTiming2_PreambleDelay = 0
m_NANDTMTiming.m_u32TMTiming2_CEDelay = 0
m_NANDTMTiming.m_u32TMTiming2_PostambleDelay = 0
m_NANDTMTiming.m_u32TMTiming2_CmdAddPause = 0
m_NANDTMTiming.m_u32TMTiming2_DataPause = 0
m_NANDTMTiming.m_u32TMSpeed = 0
m_NANDTMTiming.m_u32TMTiming1_BusyTimeout = 0
m_u32DISBBM = 0
DBBT
m_u32Checksum = 0x00000000
m_u32FingerPrint = 0x54424244
m_u32Version = 0x01000000
m_u32DBBTNumOfPages = 0
Firmware: image #0 @ 0x100000 size 0x8a000 - available 0x380000
Firmware: image #1 @ 0x480000 size 0x8a000 - available 0x380000
-------------- Start to write the [ FCB ] -----
mtd: erasing @0:0x0-0x20000
mtd: Writing FCB0 [ @0:0x0 ] (840) *
mtd: erasing @0:0x20000-0x40000
mtd: Writing FCB1 [ @0:0x20000 ] (840) *
mtd: erasing @0:0x40000-0x60000
mtd: Writing FCB2 [ @0:0x40000 ] (840) *
mtd: erasing @0:0x60000-0x80000
mtd: Writing FCB3 [ @0:0x60000 ] (840) *
mtd_commit_bcb(FCB): status 0
-------------- Start to write the [ DBBT ] -----
mtd: erasing @0:0x80000-0xa0000
mtd: Writing DBBT0 [ @0:0x80000 ] (800) *
mtd: erasing @0:0xa0000-0xc0000
mtd: Writing DBBT1 [ @0:0xa0000 ] (800) *
mtd: erasing @0:0xc0000-0xe0000
mtd: Writing DBBT2 [ @0:0xc0000 ] (800) *
mtd: erasing @0:0xe0000-0x100000
mtd: Writing DBBT3 [ @0:0xe0000 ] (800) *
mtd_commit_bcb(DBBT): status 0
---------- Start to write the [ .tmp_kobs_ng ]----
mtd: Writting .tmp_kobs_ng: #0 @0: 0x00100000 - 0x0018a000
mtd: erasing @0:0x100000-0x120000
mtd: erasing @0:0x120000-0x140000
mtd: erasing @0:0x140000-0x160000
mtd: erasing @0:0x160000-0x180000
mtd: erasing @0:0x180000-0x1a0000
mtd: The last page is not full : 928
mtd: We write one page for save guard. *
mtd: Writting .tmp_kobs_ng: #1 @0: 0x00480000 - 0x0050a000
mtd: erasing @0:0x480000-0x4a0000
mtd: erasing @0:0x4a0000-0x4c0000
mtd: erasing @0:0x4c0000-0x4e0000
mtd: erasing @0:0x4e0000-0x500000
mtd: erasing @0:0x500000-0x520000
mtd: The last page is not full : 928
mtd: We write one page for save guard. *
root@axel-lite:~#
For more details, please refer to this page.
Program root file system in NAND flash[edit | edit source]
This is a common step for both booting options.
- Boot the system via SD or NFS as described into the Quick_start_guide
- By default, the NAND is already partitioned to allow booting from NAND-only (see next section) and, thus, some partitions are reserved for U-boot and kernel images. Here we won't modify this default configuration. The MTD partitions can be dumped with
/proc/mtd(the partition's name should be self-explanatory)
root@axel-lite:~# cat /proc/mtd dev: size erasesize name mtd0: 00800000 00020000 "nand-uboot" mtd1: 00100000 00020000 "nand-env1" mtd2: 00100000 00020000 "nand-env2" mtd3: 00100000 00020000 "nand-fdt" mtd4: 00100000 00020000 "nand-spare" mtd5: 00800000 00020000 "nand-kernel" mtd6: 00400000 00020000 "nand-splash" mtd7: 1e800000 00020000 "nand-ubi" mtd8: 00100000 00010000 "spi-uboot" mtd9: 00040000 00010000 "spi-env1" mtd10: 00040000 00010000 "spi-env2" mtd11: 00080000 00010000 "spi-dtb" mtd12: 00600000 00010000 "spi-kernel" mtd13: 00400000 00010000 "spi-splash" mtd14: 01400000 00010000 "spi-free" root@axel-lite:~#
 Please note that MTD partition index may change depending of flash device availability, flash device size, u-boot environment variables or kernel device driver load order. Always take care of looking inside |
- Format and initialize nand-ubi partition, which in our case is
mtd7, using UBI with:
ubiformat /dev/mtd7 ubiattach -m 7 ubimkvol /dev/ubi0 -N rootfs -m
E.g.
root@axel-lite:~# ubiformat /dev/mtd7 ubiformat: mtd7 (nand), size 511705088 bytes (488.0 MiB), 3904 eraseblocks of 131072 bytes (128.0 KiB), min. I/O size 2048 bytes libscan: scanning eraseblock 3903 -- 100 % complete ubiformat: 3904 eraseblocks have valid erase counter, mean value is 31 ubiformat: formatting eraseblock 3903 -- 100 % complete root@axel-lite:~# ubiattach -m 7 [ 517.999286] UBI: attaching mtd7 to ubi0 [ 524.468201] UBI: scanning is finished [ 524.498833] UBI: attached mtd7 (name "nand-ubi", size 488 MiB) to ubi0 [ 524.505476] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes [ 524.512290] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 [ 524.519046] UBI: VID header offset: 2048 (aligned 2048), data offset: 4096 [ 524.525984] UBI: good PEBs: 3904, bad PEBs: 0, corrupted PEBs: 0 [ 524.532010] UBI: user volume: 0, internal volumes: 1, max. volumes count: 128 [ 524.539190] UBI: max/mean erase counter: 33/32, WL threshold: 4096, image sequence number: 483560195 [ 524.548381] UBI: available PEBs: 3820, total reserved PEBs: 84, PEBs reserved for bad PEB handling: 80 [ 524.557836] UBI: background thread "ubi_bgt0d" started, PID 856 UBI device number 0, total 3904 LEBs (495714304 bytes, 472.8 MiB), available 3820 LEBs (485048320 bytes, 462.6 MiB), LEB size 126976 bytes (124.0 KiB) root@axel-lite:~# ubimkvol /dev/ubi0 -N rootfs -m Set volume size to 485048320 Volume ID 0, size 3820 LEBs (485048320 bytes, 462.6 MiB), LEB size 126976 bytes (124.0 KiB), dynamic, name "rootfs", alignment 1 root@axel-lite:~#
- Now mount the UBI volume using UBIFS in a temporary directory
mkdir -p /mnt/nand mount -t ubifs ubi0_0 /mnt/nand
E.g.:
root@axel-lite:~# mkdir -p /mnt/nand root@axel-lite:~# mount -t ubifs ubi0_0 /mnt/nand [ 553.177151] UBIFS: default file-system created [ 553.186049] UBIFS: background thread "ubifs_bgt0_0" started, PID 860 [ 553.366834] UBIFS: mounted UBI device 0, volume 0, name "rootfs" [ 553.372931] UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes [ 553.382300] UBIFS: FS size: 483016704 bytes (460 MiB, 3804 LEBs), journal size 24252416 bytes (23 MiB, 191 LEBs) [ 553.392542] UBIFS: reserved for root: 4952683 bytes (4836 KiB) [ 553.398464] UBIFS: media format: w4/r0 (latest is w4/r0), UUID CB1521BE-B0D5-4CDA-B52A-25BAFDB755C2, small LPT model root@axel-lite:~#
- you can now extract the root file system into that directory
tar xvjf xelk-2.2.0_axel-fsl-image-qt5-xelk-l.tar.bz2 -C /mnt/nand
- finally, you need to cleanly umount and detach the MTD partition
umount /mnt/nand/ ubidetach -m 7
E.g.
root@axel-lite:~# umount /mnt/nand/ [ 575.115560] UBIFS: un-mount UBI device 0, volume 0 [ 575.120424] UBIFS: background thread "ubifs_bgt0_0" stops root@axel-lite:~# ubidetach -m 7 [ 575.171074] UBI: detaching mtd7 from ubi0 [ 575.182401] UBI: mtd7 is detached from ubi0 root@axel-lite:~#
You can now safely reboot or turn off the system.
In U-Boot environment check the following variable, which must contain the same MTD partition number used above
nand_args=setenv bootargs ubi.mtd=7 root=ubi0_0 rootfstype=ubifs rw
Note: In Xelk-3.0.0 nand_args has been replaced by nandargs
Program boot images[edit | edit source]
NOR flash[edit | edit source]
We assume that the following environment variables are present in u-boot:
loadk=tftpboot ${loadaddr} ${serverip}:${bootfile}
loadfdt=tftpboot ${fdtaddr} ${serverip}:${fdtfile}
spi_updatek=sf erase 200000 600000; sf write ${loadaddr} 200000 ${filesize}
spi_updatefdt=sf erase 180000 80000; sf write ${fdtaddr} 180000 ${filesize}
spi_loadk=sf read ${loadaddr} 200000 600000
spi_loadfdt=sf read ${fdtaddr} 180000 80000
spi_nand=sf probe; run spi_loadk spi_loadfdt nandargs addcons addmisc; if run configid_fixupfdt; then bootm ${loadaddr} - ${fdtaddr}; fi
- Update the
bootfileandfdtfileenvironment variables to fit the filename as found inside the TFTP server. - Program kernel and device tree on NOR flash with the following U-Boot command
sf probe; run loadk spi_updatek loadfdt spi_updatefdt
E.g.:
U-Boot > sf probe; run loadk spi_updatek loadfdt spi_updatefdt
SF: Detected S25FL256S with page size 64 KiB, total 32 MiB
Using FEC device
TFTP from server 192.168.0.13; our IP address is 192.168.0.98
Filename 'axel/linux/xelk-2.3.1_uImage'.
Load address: 0x12000000
Loading: #################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#############################################
1.6 MiB/s
done
Bytes transferred = 5887704 (59d6d8 hex)
Using FEC device
TFTP from server 192.168.0.13; our IP address is 192.168.0.98
Filename 'axel/linux/xelk-2.3.1_imx6q-xelk-l-2.0.0.dtb'.
Load address: 0x18000000
Loading: ##########
1.2 MiB/s
done
Bytes transferred = 46326 (b4f6 hex)
U-Boot >
Reboot the system and configure U-Boot to apply the new configuration
U-Boot > setenv bootcmd run spi_nand U-Boot > saveenv
NAND flash[edit | edit source]
We assume that the following environment variables are present in u-boot:
nand_updatek=nand erase.part nand-kernel; nand write ${loadaddr} nand-kernel ${filesize}
nand_updatefdt=nand erase.part nand-fdt; nand write ${fdtaddr} nand-fdt ${filesize}
nand_loadk=nand read ${loadaddr} nand-kernel
nand_loadfdt=nand read ${fdtaddr} nand-fdt
nand_nand=run nand_loadk nand_loadfdt nandargs addcons addmisc; if run configid_fixupfdt; then bootm ${loadaddr} - ${fdtaddr}; fi
- Update the
bootfileandfdtfileenvironment variables to fit the filename as found inside the TFTP server. - Program kernel and device tree on NAND flash with the following U-Boot command
run loadk nand_updatek loadfdt nand_updatefdt
E.g.:
U-Boot > run loadk nand_updatek loadfdt nand_updatefdt
Using FEC device
TFTP from server 192.168.0.13; our IP address is 192.168.0.98
Filename 'axel/linux/xelk-2.3.1_uImage'.
Load address: 0x12000000
Loading: #################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#############################################
1.6 MiB/s
done
Bytes transferred = 5887704 (59d6d8 hex)
NAND erase.part: device 0 offset 0xc00000, size 0x800000
size adjusted to 0x7e0000 (1 bad blocks)
Skipping bad block at 0x00d60000
Erasing at 0x13c0000 -- 100% complete.
OK
NAND write: device 0 offset 0xc00000, size 0x59d6d8
Skip bad block 0x00d60000
5887704 bytes written: OK
Using FEC device
TFTP from server 192.168.0.13; our IP address is 192.168.0.98
Filename 'axel/linux/xelk-2.3.1_imx6q-xelk-l-2.0.0.dtb'.
Load address: 0x18000000
Loading: ##########
1.3 MiB/s
done
Bytes transferred = 46326 (b4f6 hex)
NAND erase.part: device 0 offset 0xa00000, size 0x100000
Erasing at 0xae0000 -- 100% complete.
OK
NAND write: device 0 offset 0xa00000, size 0xb4f6
46326 bytes written: OK
U-Boot >
Reboot the system and configure U-Boot to apply the new configuration
U-Boot > setenv bootcmd run nand_nand U-Boot > saveenv
