[1] Not included in the kit. [2] Carrier Board 0x00000013 (SBC Lynx CS214515B) uses same dtb file as 0x0000000C [3] Carrier Board 0x0000002D/2E/2F/30 have its own device tree file for different peripherals mapping
====Downloadable binary images====
A summary of images with a brief description can be found into the table below:
{{ImportantMessage|text=In For [[AXEL_ULite_and_SBC_Lynx_Embedded_Linux_Kit_(XUELK)#XUELK_software_components|XUELK releases]] 1.1.3 and older, in order to boot Linux from SD card files, '''the binary files must be renamed''' as follows:
*bootscript: <code>boot.scr</code>
*Linux kernel: <code>uImage</code>
*Device tree: <code>imx6ul-lynx-som000c.dtb</code> or <code>imx6ul-lynx-som0013.dtb</code> The default U-boot file <code>u-bootBoot enviroment variables assume in fact that these names are used.imx</code> must be stored into first raw sector of the SD card using <code>dd</code> command}}
It is worth remembering that the microSD card is [[Booting_options_(SBC_Lynx)|bootable]], because U-Boot image is stored at address 0x400. However, even if U-Boot is run from the microSD card, '''the environment is retrieved from NOR flash'''.
====How to create a bootable microSD card====
Please refer to this [[How_to_create_a_bootable_microSD_card_(XUELK)|this page]].
=== XUELK updates ===
=== Release notes ===
==== XUELK 2.0.1/2.0.2 ==== ===== Notes 2.0.2 ===== * Update Yocto BSP to latest Krogoth to fix WPA2 key replay security bug (for more details see [http://git.yoctoproject.org/cgit/cgit.cgi/poky/commit/?h=krogoth&id=54e3f82bd77203c3d578e26c86506e6ef5c27000]) ===== Notes 2.0.1 =====Major update on XUELK 1.2 .0:* BSP update to NXP 4.1.15-2.0.0_ga* Minor fixes for Wifi and BT ===== Known issues and limitations ===== The following table reports the known limitations of this XUELK release: {| class="wikitable" |-!Limitations!Description|-|USB OTG Current Limit|USB OTG current limit is set at 75mA in Host mode|-|Low Power Idle not supported|Low Power Idle is not supported in this release|} ==== XUELK 1.2.0 ==== ===== Notes ===== Minor update on XUELK 1.1.3:* add CPU temperature for thermal thresholds settings* add rf kill support for Bluetooth on device tree* add [[ConfigID and UniqueID|ConfigID]] support for different hardware configurations: SOM_ConfigID and CB_ConfigID* minor fixes and enhancement ===== Known issues and limitations ===== The following table reports the known limitations of this XUELK release: {| class="wikitable" |-!Issue!Description|-|USB OTG Current Limit|USB OTG current limit is set at 75mA in Host mode|-|Low Power Idle not supported|Low Power Idle is not supported in this release|-|Bridged network configuration without DHCP server|See [[VirtualBox_Network_Configuration#LXDE|this section]].|} ==== XUELK 1.1.3 ====
===== Notes =====
===Target setup and first boot===
This section describes how to quick start SBC Lynx board delivered along with XUELK kit(see also the following image):
*connect a TTL/USB serial cable to J42 connector; J42 pinout is:
** 1: TX data
* change dir to the ext3 SD card partition
* delete previous files and extract new files from tarball archive as described [[AXEL_ULite_and_SBC_Lynx_Embedded_Linux_Kit_(XUELK)#Update_rfs_on_target|here]]
===Developing the software for the target===
Please refer to [[Developing the software for the target (XUELK)|this page]].