SBCX-TN-006: Characterizing the RAM bandwidth of Axel Lite SoM

Info Box Applies to Axel Ultra Applies to AXEL ESATTA Applies to Axel Lite Applies to AXEL Lite Technical Notes Applies to SMARX Technical Notes Applies to SBC AXEL Applies to SBC Axel Technical Notes

This technical note was validated against specific versions of hardware and software. What is described here may not work with other versions.

History

Version	Date	Notes
1.0.0	January 2020	First public release

Introduction

When dealing with computationally heavy tasks, the RAM bandwidth may be a severe bottleneck bounding the overall performance. This is true especially for the SoC's used in embedded systems. For this reason, characterizing the RAM bandwidth is useful when dealing with such demanding applications.

This technical note (TN for short) illustrates several benchmarking tests that were run on Axel Lite SoM to characterize its RAM bandwidth. As known, this SoM is built upon the i.MX6Q/D/DL/S family of processors by NXP.

Testbed general configuration

This section illustrates the configuration settings common to all the tests that were performed. Basically, the testbed is the same described in this TN. As such, it consists of Axel Lite SoM and SBCX carrier board.

SoC and SDRAM bank

The SoC model is i.MX6Q:

armbian@sbcx:~/devel/stream/lmbench$ lscpu 
Architecture:        armv7l
Byte Order:          Little Endian
CPU(s):              4
On-line CPU(s) list: 0-3
Thread(s) per core:  1
Core(s) per socket:  4
Socket(s):           1
Vendor ID:           ARM
Model:               10
Model name:          Cortex-A9
Stepping:            r2p10
CPU max MHz:         996.0000
CPU min MHz:         396.0000
BogoMIPS:            7.54
Flags:               half thumb fastmult vfp edsp neon vfpv3 tls vfpd32

This processor is capable of running at different speeds. All the tests were conducted at 996 MHz.

The following table details the characteristics of the SDRAM bank connected to the SoC.

SoC and SDRAM bank configuration

Subsystem	Feature	Platform
		Axel Lite
SoC	SoC	NXP i.MX6Q
	ARM core frequency [MHz]	996
	L1 cache (D) [kB]	32
	L1 cache (I) [kB]	32
	L2 cache [MB]	1
SDRAM	Type	DDR3
	Frequency [MHz]	533 (*)
	Bus witdth [bit]	64
	Theoretical bandwidth [Gb/s]	68.2
	Theoretical bandwidth [GB/s]	7.9
	Size [MB]	2048

(*) It is worth remembering that i.MX6DualLite/Solo could achieve better results in terms of memory bandwidth, even though their SDRAM bus frequency is lower (400 MHz). This is due to an errata of the ARM PL310 L2 cache controller. This bug is not present in the i.MX6DualLite/Solo SoC's, which integrate a newer version of the controller.

Software configuration

• Linux kernel: 4.9.11
• Root file system: Debian GNU/Linux 10 (buster)
• Architecture: armv7l
• Governor: userspace @ 996 MHz

armbian@sbcx:~/devel/stream/lmbench$ cat /sys/devices/system/cpu/cpu0/cpufreq/scaling_governor
userspace
armbian@sbcx:~/devel/stream/lmbench$ cat /sys/devices/system/cpu/cpu0/cpufreq/scaling_cur_freq
996000

Some benchmarks were built natively on the platform under test. For the sake of completeness, the version of the GCC compiler is then indicated as well:

armbian@sbcx:~/devel/stream/lmbench$ gcc -v
Using built-in specs.
COLLECT_GCC=gcc
COLLECT_LTO_WRAPPER=/usr/lib/gcc/arm-linux-gnueabihf/8/lto-wrapper
Target: arm-linux-gnueabihf
Configured with: ../src/configure -v --with-pkgversion='Debian 8.3.0-6' --with-bugurl=file:///usr/share/doc/gcc-8/README.Bugs --enable-languages=c,ada,c++,go,d,fortran,objc,obj-c++ --prefix=/usr --with-gcc-major-version-only --program-suffix=-8 --program-prefix=arm-linux-gnueabihf- --enable-shared --enable-linker-build-id --libexecdir=/usr/lib --without-included-gettext --enable-threads=posix --libdir=/usr/lib --enable-nls --enable-bootstrap --enable-clocale=gnu --enable-libstdcxx-debug --enable-libstdcxx-time=yes --with-default-libstdcxx-abi=new --enable-gnu-unique-object --disable-libitm --disable-libquadmath --disable-libquadmath-support --enable-plugin --enable-default-pie --with-system-zlib --with-target-system-zlib --enable-objc-gc=auto --enable-multiarch --disable-sjlj-exceptions --with-arch=armv7-a --with-fpu=vfpv3-d16 --with-float=hard --with-mode=thumb --disable-werror --enable-checking=release --build=arm-linux-gnueabihf --host=arm-linux-gnueabihf --target=arm-linux-gnueabihf
Thread model: posix
gcc version 8.3.0 (Debian 8.3.0-6) 

Overall results

This section illustrates the overall results achieved by the benchmarks.

STREAM

Overall results

Function	Best rate [MB/s]	Efficiency [%]
Copy	1139.8	14.0
Scale	1124.8	13.8
Add	1185.1	14.6
Triad	1214.4	14.9

As expected, the efficiency is relatively low. Generally, 32-bit ARM architectures are known to have mediocre performances when it comes to memory bandwidth.

Please see this page for more details about STREAM benchmark.

LMbench

For what regards the memory bandwidth, LMbench provides many results organized in different categories. For the sake of simplicity, the following tables details just a couple of categories. The full results are available for download here.

Memory read bandwidth

Buffer size	Bandwitdth [MB/s]
512B	2861
1kB	3047
2kB	3065
4kB	3077
8kB	3081
16kB	3072
32kB	1309
64kB	902
128kB	787
256kB	775
512kB	749
1MB	687
2MB	642
4MB	629
8MB	630
16MB	632
32MB	631
64MB	632
128MB	633
256MB	634
512MB	634
1GB	633

Memory write bandwidth

Buffer size	Bandwitdth [MB/s]
512B	3724
1kB	3848
2kB	3902
4kB	3940
8kB	3958
16kB	3957
32kB	3964
64kB	3967
128kB	3967
256kB	3956
512kB	3947
1MB	2097
2MB	2154
4MB	2114
8MB	2082
16MB	2084
32MB	2085
64MB	2093
128MB	2086
256MB	2089
512MB	2087
1GB	2088

The most interesting results to consider are those that refer to buffer sizes exceeding 1MB, which is the size of the L2 cache. Approximately, read bandwidth is 630MB/s (7.8% efficiency), while write bandwidth is 2080 MB/s (25.7% efficiency). These numbers are significantly different that the ones provided by STREAM. This confirms once again that such results are strongly dependent on the implementation of the test used to determine the bandwidth.

For more information regarding LMbench, please see this page.

pmbw

As defined by the author, pmbw is "a set of assembler routines to measure the parallel memory (cache and RAM) bandwidth of modern multi-core machines." It performs a myriad of tests. Luckily, it comes with a handful tool that plots the results—which are stored in a text file—in a series of charts.

The complete results and the charts are available at the following links:

• http://mirror.dave.eu/axel/SBCX-TN-006/pmbw-stats-AxelLite-i.MX6Q-996MHz.txt
• http://mirror.dave.eu/axel/SBCX-TN-006/pmbw-plots-AxelLite-i.MX6Q-996MHz.pdf

Generally speaking, the charts exhibit significant declines in the performances when the array size is around the L1 and the L2 cache size.

For more details about pmbw, please refer to this page.

Useful links

• Joshua Wyatt Smith and Andrew Hamilton, Parallel benchmarks for ARM processors in the highenergy context
• T Wrigley, G Harmsen and B Mellado, Memory performance of ARM processors and itsrelevance to High Energy Physics
• G. T. Wrigley, R. G. Reed, B. Mellado, Memory benchmarking characterisation of ARM-based SoCs

Appendix A: Detailed testing procedures

This section details how the benchmarks were configured and run on the testbed.

STREAM

Building

To build STREAM:

• clone its git repository
• modify the Makefile as shown below
• issue the make command.

git clone https://github.com/jeffhammond/STREAM.git
make

 1 armbian@Mito8M:~/devel/STREAM$ cat Makefile 
 2 CC = gcc
 3 CFLAGS = -O2 -fopenmp
 4 
 5 FC = gfortran-4.9
 6 FFLAGS = -O2 -fopenmp
 7 
 8 all: stream_c.exe
 9 
10 stream_f.exe: stream.f mysecond.o
11         $(CC) $(CFLAGS) -c mysecond.c
12         $(FC) $(FFLAGS) -c stream.f
13         $(FC) $(FFLAGS) stream.o mysecond.o -o stream_f.exe
14 
15 stream_c.exe: stream.c
16         $(CC) $(CFLAGS) stream.c -o stream_c.exe
17 
18 clean:
19         rm -f stream_f.exe stream_c.exe *.o
20 
21 # an example of a more complex build line for the Intel icc compiler
22 stream.icc: stream.c
23         icc -O3 -xCORE-AVX2 -ffreestanding -qopenmp -DSTREAM_ARRAY_SIZE=80000000 -DNTIMES=20 stream.c -o stream.omp.AVX2.80M.20x.icc

Running the tests

armbian@sbcx:~/devel/stream/STREAM$ ./stream_c.exe 
-------------------------------------------------------------
STREAM version $Revision: 5.10 $
-------------------------------------------------------------
This system uses 8 bytes per array element.
-------------------------------------------------------------
Array size = 10000000 (elements), Offset = 0 (elements)
Memory per array = 76.3 MiB (= 0.1 GiB).
Total memory required = 228.9 MiB (= 0.2 GiB).
Each kernel will be executed 10 times.
 The *best* time for each kernel (excluding the first iteration)
 will be used to compute the reported bandwidth.
-------------------------------------------------------------
Number of Threads requested = 4
Number of Threads counted = 4
-------------------------------------------------------------
Your clock granularity/precision appears to be 1 microseconds.
Each test below will take on the order of 153104 microseconds.
   (= 153104 clock ticks)
Increase the size of the arrays if this shows that
you are not getting at least 20 clock ticks per test.
-------------------------------------------------------------
WARNING -- The above is only a rough guideline.
For best results, please be sure you know the
precision of your system timer.
-------------------------------------------------------------
Function    Best Rate MB/s  Avg time     Min time     Max time
Copy:            1139.8     0.141910     0.140376     0.144318
Scale:           1124.8     0.143720     0.142245     0.144615
Add:             1185.1     0.204792     0.202517     0.206718
Triad:           1214.4     0.201321     0.197631     0.202673
-------------------------------------------------------------
Solution Validates: avg error less than 1.000000e-13 on all three arrays
-------------------------------------------------------------

LMbench

To run this benchmark, the native prebuilt package provided by Debian Buster was used.

armbian@sbcx:~/devel/stream/STREAM$ sudo lmbench-run 
=====================================================================

                L M B E N C H   C ON F I G U R A T I O N
                ----------------------------------------

You need to configure some parameters to lmbench.  Once you have configured
these parameters, you may do multiple runs by saying

        "make rerun"

in the src subdirectory.

NOTICE: please do not have any other activity on the system if you can
help it.  Things like the second hand on your xclock or X perfmeters
are not so good when benchmarking.  In fact, X is not so good when
benchmarking.

=====================================================================

If you are running on an MP machine and you want to try running
multiple copies of lmbench in parallel, you can specify how many here.

Using this option will make the benchmark run 100x slower (sorry).

NOTE:  WARNING! This feature is experimental and many results are 
        known to be incorrect or random!

MULTIPLE COPIES [default 1]: 
=====================================================================

Options to control job placement
1) Allow scheduler to place jobs
2) Assign each benchmark process with any attendent child processes
   to its own processor
3) Assign each benchmark process with any attendent child processes
   to its own processor, except that it will be as far as possible
   from other processes
4) Assign each benchmark and attendent processes to their own
   processors
5) Assign each benchmark and attendent processes to their own
   processors, except that they will be as far as possible from
   each other and other processes
6) Custom placement: you assign each benchmark process with attendent
   child processes to processors
7) Custom placement: you assign each benchmark and attendent
   processes to processors

Note: some benchmarks, such as bw_pipe, create attendent child
processes for each benchmark process.  For example, bw_pipe
needs a second process to send data down the pipe to be read
by the benchmark process.  If you have three copies of the
benchmark process running, then you actually have six processes;
three attendent child processes sending data down the pipes and 
three benchmark processes reading data and doing the measurements.

Job placement selection [default 1]: 
=====================================================================

Hang on, we are calculating your timing granularity.
OK, it looks like you can time stuff down to 5000 usec resolution.

Hang on, we are calculating your timing overhead.
OK, it looks like your gettimeofday() costs 0 usecs.

Hang on, we are calculating your loop overhead.
OK, it looks like your benchmark loop costs 0.00000055 usecs.

=====================================================================

Several benchmarks operate on a range of memory.  This memory should be
sized such that it is at least 4 times as big as the external cache[s]
on your system.   It should be no more than 80% of your physical memory.

The bigger the range, the more accurate the results, but larger sizes
take somewhat longer to run the benchmark.

MB [default 1186]: 1024
Checking to see if you have 1024 MB; please wait for a moment...
1024MB OK
1024MB OK
1024MB OK
Hang on, we are calculating your cache line size.
OK, it looks like your cache line is 32 bytes.

=====================================================================

lmbench measures a wide variety of system performance, and the full suite
of benchmarks can take a long time on some platforms.  Consequently, we
offer the capability to run only predefined subsets of benchmarks, one
for operating system specific benchmarks and one for hardware specific
benchmarks.  We also offer the option of running only selected benchmarks
which is useful during operating system development.

Please remember that if you intend to publish the results you either need
to do a full run or one of the predefined OS or hardware subsets.

SUBSET (ALL|HARWARE|OS|DEVELOPMENT) [default all]: 
=====================================================================

This benchmark measures, by default, memory latency for a number of
different strides.  That can take a long time and is most useful if you
are trying to figure out your cache line size or if your cache line size
is greater than 128 bytes.

If you are planning on sending in these results, please don't do a fast
run.

Answering yes means that we measure memory latency with a 128 byte stride.  

FASTMEM [default no]: 
=====================================================================

This benchmark measures, by default, file system latency.  That can
take a long time on systems with old style file systems (i.e., UFS,
FFS, etc.).  Linux' ext2fs and Sun's tmpfs are fast enough that this
test is not painful.

If you are planning on sending in these results, please don't do a fast
run.

If you want to skip the file system latency tests, answer "yes" below.

SLOWFS [default no]: yes
=====================================================================

This benchmark can measure disk zone bandwidths and seek times.  These can
be turned into whizzy graphs that pretty much tell you everything you might
need to know about the performance of your disk.  

This takes a while and requires read access to a disk drive.  
Write is not measured, see disk.c to see how if you want to do so.

If you want to skip the disk tests, hit return below.

If you want to include disk tests, then specify the path to the disk
device, such as /dev/sda.  For each disk that is readable, you'll be
prompted for a one line description of the drive, i.e., 

        Iomega IDE ZIP
or
        HP C3725S 2GB on 10MB/sec NCR SCSI bus

DISKS [default none]: 
=====================================================================

If you are running on an idle network and there are other, identically
configured systems, on the same wire (no gateway between you and them),
and you have rsh access to them, then you should run the network part
of the benchmarks to them.  Please specify any such systems as a space
separated list such as: ether-host fddi-host hippi-host.

REMOTE [default none]: 
=====================================================================

Calculating mhz, please wait for a moment...
I think your CPU mhz is 

        1992 MHz, 0.5020 nanosec clock

but I am frequently wrong.  If that is the wrong Mhz, type in your
best guess as to your processor speed.  It doesn't have to be exact,
but if you know it is around 800, say 800.  

Please note that some processors, such as the P4, have a core which
is double-clocked, so on those processors the reported clock speed
will be roughly double the advertised clock rate.  For example, a
1.8GHz P4 may be reported as a 3592MHz processor.

Processor mhz [default 1992 MHz, 0.5020 nanosec clock]: 996
=====================================================================

We need a place to store a 1024 Mbyte file as well as create and delete a
large number of small files.  We default to /var/tmp.  If /var/tmp is a
memory resident file system (i.e., tmpfs), pick a different place.
Please specify a directory that has enough space and is a local file
system.

FSDIR [default /var/tmp/lmbench]: /home/armbian/devel/stream/lmbench
=====================================================================

lmbench outputs status information as it runs various benchmarks.
By default this output is sent to /dev/tty, but you may redirect
it to any file you wish (such as /dev/null...).

Status output file [default /dev/tty]: 
=====================================================================

There is a database of benchmark results that is shipped with new
releases of lmbench.  Your results can be included in the database
if you wish.  The more results the better, especially if they include
remote networking.  If your results are interesting, i.e., for a new
fast box, they may be made available on the lmbench web page, which is

        http://www.bitmover.com/lmbench

Mail results [default yes]: no
OK, no results mailed.
=====================================================================

Confguration done, thanks.

There is a mailing list for discussing lmbench hosted at BitMover. 
Send mail to majordomo@bitmover.com to join the list.

Using config in CONFIG.sbcx
Thu Jan 24 09:27:32 CET 2020
Latency measurements
Thu Jan 24 09:28:38 CET 2020
Local networking
Fri Jan 24 09:29:38 CET 2020
Bandwidth measurements
Fri Jan 24 09:41:01 CET 2020
Calculating context switch overhead
Fri Jan 24 09:41:06 CET 2020
Calculating effective TLB size
Fri Jan 24 09:41:08 CET 2020
Calculating memory load parallelism
Fri Jan 24 09:53:02 CET 2020
McCalpin's STREAM benchmark
Fri Jan 24 09:54:55 CET 2020
Calculating memory load latency
Fri Jan 24 10:28:12 CET 2020
Benchmark run finished....
Remember you can find the results of the benchmark 
under /var/lib/lmbench/results

pmbw

Building

Building pmbw is straightforward. Please click on Expand to show the box that illustrates the procedure.

armbian@sbcx:~/devel/pmbw$ git clone https://github.com/bingmann/pmbw.git
Cloning into 'pmbw'...
remote: Enumerating objects: 15, done.
remote: Counting objects: 100% (15/15), done.
remote: Compressing objects: 100% (15/15), done.
remote: Total 386 (delta 1), reused 3 (delta 0), pack-reused 371
Receiving objects: 100% (386/386), 369.04 KiB | 1.23 MiB/s, done.
Resolving deltas: 100% (232/232), done.
armbian@sbcx:~/devel/pmbw$ cd pmbw/
armbian@sbcx:~/devel/pmbw/pmbw$ ./configure && make
checking build system type... armv7l-unknown-linux-gnueabihf
checking host system type... armv7l-unknown-linux-gnueabihf
checking target system type... armv7l-unknown-linux-gnueabihf
checking for a BSD-compatible install... /usr/bin/install -c
checking whether build environment is sane... yes
checking for a thread-safe mkdir -p... /bin/mkdir -p
checking for gawk... no
checking for mawk... mawk
checking whether make sets $(MAKE)... yes
checking whether make supports nested variables... yes
checking whether to enable maintainer-specific portions of Makefiles... no
checking building for Windows... no
checking for g++... g++
checking whether the C++ compiler works... yes
checking for C++ compiler default output file name... a.out
checking for suffix of executables... 
checking whether we are cross compiling... no
checking for suffix of object files... o
checking whether we are using the GNU C++ compiler... yes
checking whether g++ accepts -g... yes
checking whether make supports the include directive... yes (GNU style)
checking dependency style of g++... gcc3
checking whether g++ supports -march=x86-64... no
checking for pthread_mutex_init in -lpthread... yes
checking for clock_gettime in -lrt... yes
checking for posix_memalign in -lc... yes
checking that generated files are newer than configure... done
configure: creating ./config.status
config.status: creating Makefile
config.status: executing depfiles commands
g++ -DPACKAGE_NAME=\"pmbw\" -DPACKAGE_TARNAME=\"pmbw\" -DPACKAGE_VERSION=\"0.6.3\" -DPACKAGE_STRING=\"pmbw\ 0.6.3\" -DPACKAGE_BUGREPORT=\"\" -DPACKAGE_URL=\"\" -DPACKAGE=\"pmbw\" -DVERSION=\"0.6.3\" -DON_WINDOWS=false -DHAVE_POSIX_MEMALIGN=1 -I.    -W -Wall -g -O2 -MT pmbw.o -MD -MP -MF .deps/pmbw.Tpo -c -o pmbw.o pmbw.cc
mv -f .deps/pmbw.Tpo .deps/pmbw.Po
g++ -W -Wall -g -O2   -o pmbw pmbw.o  -lpthread -lrt
g++ -DPACKAGE_NAME=\"pmbw\" -DPACKAGE_TARNAME=\"pmbw\" -DPACKAGE_VERSION=\"0.6.3\" -DPACKAGE_STRING=\"pmbw\ 0.6.3\" -DPACKAGE_BUGREPORT=\"\" -DPACKAGE_URL=\"\" -DPACKAGE=\"pmbw\" -DVERSION=\"0.6.3\" -DON_WINDOWS=false -DHAVE_POSIX_MEMALIGN=1 -I.    -W -Wall -g -O2 -MT stats2gnuplot.o -MD -MP -MF .deps/stats2gnuplot.Tpo -c -o stats2gnuplot.o stats2gnuplot.cc
In file included from /usr/include/c++/8/vector:69,
                 from stats2gnuplot.cc:34:
/usr/include/c++/8/bits/vector.tcc: In member function 'void std::vector<_Tp, _Alloc>::_M_realloc_insert(std::vector<_Tp, _Alloc>::iterator, _Args&& ...) [with _Args = {const Result&}; _Tp = Result; _Alloc = std::allocator<Result>]':
/usr/include/c++/8/bits/vector.tcc:413:7: note: parameter passing for argument of type 'std::vector<Result>::iterator' {aka '__gnu_cxx::__normal_iterator<Result*, std::vector<Result> >'} changed in GCC 7.1
       vector<_Tp, _Alloc>::
       ^09:46, 24 January 2020 (UTC)09:46, 24 January 2020 (UTC)09:46, 24 January 2020 (UTC)[[User:U0001|U0001]] ([[User talk:U0001|talk]])
In file included from /usr/include/c++/8/vector:64,
                 from stats2gnuplot.cc:34:
/usr/include/c++/8/bits/stl_vector.h: In function 'bool process_line(const string&)':
/usr/include/c++/8/bits/stl_vector.h:1085:4: note: parameter passing for argument of type '__gnu_cxx::__normal_iterator<Result*, std::vector<Result> >' changed in GCC 7.1
    _M_realloc_insert(end(), __x);
    ^09:46, 24 January 2020 (UTC)09:46, 24 January 2020 (UTC)09:46, 24 January 2020 (UTC)~
In file included from /usr/include/c++/8/algorithm:62,
                 from stats2gnuplot.cc:33:
/usr/include/c++/8/bits/stl_algo.h: In function 'void std::__unguarded_linear_insert(_RandomAccessIterator, _Compare) [with _RandomAccessIterator = __gnu_cxx::__normal_iterator<Result*, std::vector<Result> >; _Compare = __gnu_cxx::__ops::_Val_less_iter]':
/usr/include/c++/8/bits/stl_algo.h:1821:5: note: parameter passing for argument of type '__gnu_cxx::__normal_iterator<Result*, std::vector<Result> >' changed in GCC 7.1
     __unguarded_linear_insert(_RandomAccessIterator __last,
     ^09:46, 24 January 2020 (UTC)09:46, 24 January 2020 (UTC)09:46, 24 January 2020 (UTC)09:46, 24 January 2020 (UTC)[[User:U0001|U0001]] ([[User talk:U0001|talk]]) 09:46, 24 January 2020 (UTC)
/usr/include/c++/8/bits/stl_algo.h: In function 'void std::__insertion_sort(_RandomAccessIterator, _RandomAccessIterator, _Compare) [with _RandomAccessIterator = __gnu_cxx::__normal_iterator<Result*, std::vector<Result> >; _Compare = __gnu_cxx::__ops::_Iter_less_iter]':
/usr/include/c++/8/bits/stl_algo.h:1840:5: note: parameter passing for argument of type '__gnu_cxx::__normal_iterator<Result*, std::vector<Result> >' changed in GCC 7.1
     __insertion_sort(_RandomAccessIterator __first,
     ^09:46, 24 January 2020 (UTC)09:46, 24 January 2020 (UTC)09:46, 24 January 2020 (UTC)
/usr/include/c++/8/bits/stl_algo.h:1840:5: note: parameter passing for argument of type '__gnu_cxx::__normal_iterator<Result*, std::vector<Result> >' changed in GCC 7.1
In file included from /usr/include/c++/8/bits/stl_algo.h:61,
                 from /usr/include/c++/8/algorithm:62,
                 from stats2gnuplot.cc:33:
/usr/include/c++/8/bits/stl_heap.h: In function 'void std::__adjust_heap(_RandomAccessIterator, _Distance, _Distance, _Tp, _Compare) [with _RandomAccessIterator = __gnu_cxx::__normal_iterator<Result*, std::vector<Result> >; _Distance = int; _Tp = Result; _Compare = __gnu_cxx::__ops::_Iter_less_iter]':
/usr/include/c++/8/bits/stl_heap.h:214:5: note: parameter passing for argument of type '__gnu_cxx::__normal_iterator<Result*, std::vector<Result> >' changed in GCC 7.1
     __adjust_heap(_RandomAccessIterator __first, _Distance __holeIndex,
     ^09:46, 24 January 2020 (UTC)09:46, 24 January 2020 (UTC)~~
/usr/include/c++/8/bits/stl_heap.h: In function 'void std::__make_heap(_RandomAccessIterator, _RandomAccessIterator, _Compare&) [with _RandomAccessIterator = __gnu_cxx::__normal_iterator<Result*, std::vector<Result> >; _Compare = __gnu_cxx::__ops::_Iter_less_iter]':
/usr/include/c++/8/bits/stl_heap.h:326:5: note: parameter passing for argument of type '__gnu_cxx::__normal_iterator<Result*, std::vector<Result> >' changed in GCC 7.1
     __make_heap(_RandomAccessIterator __first, _RandomAccessIterator __last,
     ^09:46, 24 January 2020 (UTC)09:46, 24 January 2020 (UTC)
/usr/include/c++/8/bits/stl_heap.h:326:5: note: parameter passing for argument of type '__gnu_cxx::__normal_iterator<Result*, std::vector<Result> >' changed in GCC 7.1
/usr/include/c++/8/bits/stl_heap.h: In function 'void std::__pop_heap(_RandomAccessIterator, _RandomAccessIterator, _RandomAccessIterator, _Compare&) [with _RandomAccessIterator = __gnu_cxx::__normal_iterator<Result*, std::vector<Result> >; _Compare = __gnu_cxx::__ops::_Iter_less_iter]':
/usr/include/c++/8/bits/stl_heap.h:243:5: note: parameter passing for argument of type '__gnu_cxx::__normal_iterator<Result*, std::vector<Result> >' changed in GCC 7.1
     __pop_heap(_RandomAccessIterator __first, _RandomAccessIterator __last,
     ^09:46, 24 January 2020 (UTC)[[User:U0001|U0001]] ([[User talk:U0001|talk]]) 09:46, 24 January 2020 (UTC)
/usr/include/c++/8/bits/stl_heap.h:243:5: note: parameter passing for argument of type '__gnu_cxx::__normal_iterator<Result*, std::vector<Result> >' changed in GCC 7.1
/usr/include/c++/8/bits/stl_heap.h:243:5: note: parameter passing for argument of type '__gnu_cxx::__normal_iterator<Result*, std::vector<Result> >' changed in GCC 7.1
In file included from /usr/include/c++/8/algorithm:62,
                 from stats2gnuplot.cc:33:
/usr/include/c++/8/bits/stl_algo.h: In function 'void std::__introsort_loop(_RandomAccessIterator, _RandomAccessIterator, _Size, _Compare) [with _RandomAccessIterator = __gnu_cxx::__normal_iterator<Result*, std::vector<Result> >; _Size = int; _Compare = __gnu_cxx::__ops::_Iter_less_iter]':
/usr/include/c++/8/bits/stl_algo.h:1940:5: note: parameter passing for argument of type '__gnu_cxx::__normal_iterator<Result*, std::vector<Result> >' changed in GCC 7.1
     __introsort_loop(_RandomAccessIterator __first,
     ^09:46, 24 January 2020 (UTC)09:46, 24 January 2020 (UTC)09:46, 24 January 2020 (UTC)
/usr/include/c++/8/bits/stl_algo.h:1940:5: note: parameter passing for argument of type '__gnu_cxx::__normal_iterator<Result*, std::vector<Result> >' changed in GCC 7.1
In file included from /usr/include/c++/8/bits/stl_algo.h:61,
                 from /usr/include/c++/8/algorithm:62,
                 from stats2gnuplot.cc:33:
/usr/include/c++/8/bits/stl_heap.h:408:19: note: parameter passing for argument of type '__gnu_cxx::__normal_iterator<Result*, std::vector<Result> >' changed in GCC 7.1
    std::__pop_heap(__first, __last, __last, __comp);
    09:46, 24 January 2020 (UTC)09:46, 24 January 2020 (UTC)09:46, 24 January 2020 (UTC)^09:46, 24 January 2020 (UTC)09:46, 24 January 2020 (UTC)09:46, 24 January 2020 (UTC)09:46, 24 January 2020 (UTC)09:46, 24 January 2020 (UTC)09:46, 24 January 2020 (UTC)~~
In file included from /usr/include/c++/8/algorithm:62,
                 from stats2gnuplot.cc:33:
/usr/include/c++/8/bits/stl_algo.h:1954:25: note: parameter passing for argument of type '__gnu_cxx::__normal_iterator<Result*, std::vector<Result> >' changed in GCC 7.1
    std::__introsort_loop(__cut, __last, __depth_limit, __comp);
    09:46, 24 January 2020 (UTC)09:46, 24 January 2020 (UTC)09:46, 24 January 2020 (UTC)09:46, 24 January 2020 (UTC)~^09:46, 24 January 2020 (UTC)09:46, 24 January 2020 (UTC)09:46, 24 January 2020 (UTC)09:46, 24 January 2020 (UTC)09:46, 24 January 2020 (UTC)09:46, 24 January 2020 (UTC)09:46, 24 January 2020 (UTC)~~
/usr/include/c++/8/bits/stl_algo.h:1672:23: note: parameter passing for argument of type '__gnu_cxx::__normal_iterator<Result*, std::vector<Result> >' changed in GCC 7.1
       std::__make_heap(__first, __middle, __comp);
       09:46, 24 January 2020 (UTC)09:46, 24 January 2020 (UTC)09:46, 24 January 2020 (UTC)~^09:46, 24 January 2020 (UTC)09:46, 24 January 2020 (UTC)09:46, 24 January 2020 (UTC)09:46, 24 January 2020 (UTC)09:46, 24 January 2020 (UTC)~
/usr/include/c++/8/bits/stl_algo.h: In function 'int main(int, char**)':
/usr/include/c++/8/bits/stl_algo.h:1968:25: note: parameter passing for argument of type '__gnu_cxx::__normal_iterator<Result*, std::vector<Result> >' changed in GCC 7.1
    std::__introsort_loop(__first, __last,
    09:46, 24 January 2020 (UTC)09:46, 24 January 2020 (UTC)09:46, 24 January 2020 (UTC)09:46, 24 January 2020 (UTC)~^09:46, 24 January 2020 (UTC)09:46, 24 January 2020 (UTC)09:46, 24 January 2020 (UTC)~
     std::__lg(__last - __first) * 2,
     09:46, 24 January 2020 (UTC)09:46, 24 January 2020 (UTC)09:46, 24 January 2020 (UTC)09:46, 24 January 2020 (UTC)09:46, 24 January 2020 (UTC)09:46, 24 January 2020 (UTC)~~
     __comp);
     09:46, 24 January 2020 (UTC)~~              
/usr/include/c++/8/bits/stl_algo.h:1885:25: note: parameter passing for argument of type '__gnu_cxx::__normal_iterator<Result*, std::vector<Result> >' changed in GCC 7.1
    std::__insertion_sort(__first, __first + int(_S_threshold), __comp);
    09:46, 24 January 2020 (UTC)09:46, 24 January 2020 (UTC)09:46, 24 January 2020 (UTC)09:46, 24 January 2020 (UTC)~^09:46, 24 January 2020 (UTC)09:46, 24 January 2020 (UTC)09:46, 24 January 2020 (UTC)09:46, 24 January 2020 (UTC)09:46, 24 January 2020 (UTC)09:46, 24 January 2020 (UTC)09:46, 24 January 2020 (UTC)09:46, 24 January 2020 (UTC)09:46, 24 January 2020 (UTC)
/usr/include/c++/8/bits/stl_algo.h:1890:23: note: parameter passing for argument of type '__gnu_cxx::__normal_iterator<Result*, std::vector<Result> >' changed in GCC 7.1
  std::__insertion_sort(__first, __last, __comp);
  09:46, 24 January 2020 (UTC)09:46, 24 January 2020 (UTC)09:46, 24 January 2020 (UTC)09:46, 24 January 2020 (UTC)~^09:46, 24 January 2020 (UTC)09:46, 24 January 2020 (UTC)09:46, 24 January 2020 (UTC)09:46, 24 January 2020 (UTC)[[User:U0001|U0001]] ([[User talk:U0001|talk]]) 09:46, 24 January 2020 (UTC)
mv -f .deps/stats2gnuplot.Tpo .deps/stats2gnuplot.Po
g++ -W -Wall -g -O2   -o stats2gnuplot stats2gnuplot.o  -lpthread -lrt

Running the tests

The benchmark was run as follows:

armbian@sbcx:~/devel/pmbw/pmbw$ sudo nice -n -2 ./pmbw -S 0
Running benchmarks with no upper array size limit.
Detected 1695 MiB physical RAM and 4 CPUs. 

Allocating 1024 MiB for testing.
Running nthreads=1 factor=1073741824 areasize=1024 thrsize=1024 testsize=1024 repeats=1048576 testvol=1073741824 testaccess=268435456
run time = 0.424801 -> rerunning test with repeat factor=3791455289
Running nthreads=1 factor=3791455289 areasize=1024 thrsize=1024 testsize=1024 repeats=3702594 testvol=3791456256 testaccess=947864064
...

To generate the charts plotting the results, the following command was issued:

./stats2gnuplot stats.txt | gnuplot