Difference between revisions of "Recovery U-Boot Image (Lizard)"
| Line 1: | Line 1: | ||
| − | + | ||
| − | * Download the zip archive lizard-Recovery.zip and extract it | + | |
| − | * Open the command prompt and go inside the | + | == Tool Preparation == |
| + | * Download the zip archive lizard-Recovery.zip and extract it | ||
| + | * Open the command prompt and go inside the folder where you extract the recovery | ||
* Lunch the uitility with the serial port number | * Lunch the uitility with the serial port number | ||
| − | C:\Users\Desktop\lizard-Recovery\lizard> .\uart- | + | <pre> |
| − | + | C:\Users\Desktop\lizard-Recovery\lizard> .\uart-recovery.bat COM1 | |
| + | </pre> | ||
{{InfoBoxTop}} | {{InfoBoxTop}} | ||
{{AppliesToLizard}} | {{AppliesToLizard}} | ||
{{AppliesToLizardEVB-Lite}} | {{AppliesToLizardEVB-Lite}} | ||
{{InfoBoxBottom}} | {{InfoBoxBottom}} | ||
| − | + | == Board Preparation == | |
* Power down the board and set the deep switch 2 1 configuration. | * Power down the board and set the deep switch 2 1 configuration. | ||
| − | * Connect the serial console to the PORT2 of your board. | + | * Connect the serial console to the <ode>PORT2</code> of your board. |
| − | * Turn the board | + | * Turn on the board. |
| − | + | == Flashing the firmware == | |
| − | If everithing was set correctly, this | + | If everithing was set correctly, this messages should appear on your screen |
<pre> | <pre> | ||
| Line 47: | Line 50: | ||
CLOSE Serial Console !!!!!! | CLOSE Serial Console !!!!!! | ||
</pre> | </pre> | ||
| + | {{ImportantMessage|text=Don't close the '''command prompt'''}} | ||
| − | Now it is necessary to open a serial console for example Putty and | + | Now it is necessary to open a serial console for example Putty and type the following command |
<pre> | <pre> | ||
mw.w ${buf} 0xFF 0x40000; loadb ${buf} 115200 | mw.w ${buf} 0xFF 0x40000; loadb ${buf} 115200 | ||
</pre> | </pre> | ||
| − | Now close the | + | Now close the serial console and pres <code>Enter</code> inside the command prompt. |
| − | A new download will start. | + | A new download will start follewd by some instructions. |
<pre> | <pre> | ||
Downloading file: 100.000% completed(218792/218792 bytes) | Downloading file: 100.000% completed(218792/218792 bytes) | ||
| Line 72: | Line 76: | ||
res | res | ||
</pre> | </pre> | ||
| − | + | Now the board will restart and if everithing went ok, you should see the U-Boot command line prompt. | |
| − | |||
| − | |||
| − | |||
| − | |||
Revision as of 10:56, 15 March 2018
| HOME | SOMs | SBCs | ToloMEO Embedded Assistant |  GET A QUOTE
|
 ONLINE HELPDESK
|
| Roadmap | IoT Services | ML/AI services | Embedded Design Services |
Tool Preparation[edit | edit source]
- Download the zip archive lizard-Recovery.zip and extract it
- Open the command prompt and go inside the folder where you extract the recovery
- Lunch the uitility with the serial port number
C:\Users\Desktop\lizard-Recovery\lizard> .\uart-recovery.bat COM1
Info Box
|
Board Preparation[edit | edit source]
- Power down the board and set the deep switch 2 1 configuration.
- Connect the serial console to the <ode>PORT2 of your board.
- Turn on the board.
Flashing the firmware[edit | edit source]
If everithing was set correctly, this messages should appear on your screen
ASIC ID Detected.
Sending 2ndFile:
Downloading file: 100.000% completed(15232/15232 bytes)
File download completed.
In attesa da 0 secondi. Premere un tasto per continuare...
Downloading file: 100.000% completed(218792/218792 bytes)
File Download completed
Open Serial Console and write this command
.
.
"=> mw.w ${buf} 0xFF 0x40000; loadb ${buf} 115200"
.
.
CLOSE Serial Console !!!!!!
 Don't close the command prompt |
Now it is necessary to open a serial console for example Putty and type the following command
mw.w ${buf} 0xFF 0x40000; loadb ${buf} 115200
Now close the serial console and pres Enter inside the command prompt.
A new download will start follewd by some instructions.
Downloading file: 100.000% completed(218792/218792 bytes)
File Download completed
.
.
Open Serial Console and write this command
"=> protect off 0x08000000 +40000;era 0x08000000 +40000;cp.b ${buf} 0x08000000 0x40000"
"=> res"
.
.
.
When the download is finished, you need to reopen putty and insert this command
protect off 0x08000000 +40000;era 0x08000000 +40000;cp.b ${buf} 0x08000000 0x40000
res
Now the board will restart and if everithing went ok, you should see the U-Boot command line prompt.
