NELK Release Notes

Info Box Applies to Naon Applies to NaonEVB-Lite Applies to NaonEVB-Mid

Naon Embedded Linux Kit (NELK) Release Notes

Rel. 4.0.0

• Release date: April 2013
• Status: planned
• EZSDK version: 5.05.02.00
• Supported carrier boards: NaonEVB-Lite, NaonEVB-Mid

Notes

• Added support for Maya and Dido SOMs
• Added support for the following interfaces/features
  • PMIC RTC (battery powered)
  • /proc/ti81xx_cpuinfo entry
  • passing the mac address from u-boot to Linux kernel (command line parameters : eth0=xx:xx:xx:xx:xx:xx eth1=xx:xx:xx:xx:xx:xx)
  • dido 2GiB RAM
  • driver CPSW dual emac mode vs switch mode at runtime

Rel. 3.0.0

• Release date: December 2012
• Status: released
• EZSDK version: 5.05
• Supported carrier boards: NaonEVB-Lite, NaonEVB-Mid

Notes

• Added support for the following interfaces/features
  • Video Input port VIN1 (additional host required)
  • SATA
  • Suspend to RAM
  • OPP Support
  • DWM (Wireless add-on module) on SDIO (NaonEVB-Lite only)
• NAND is supported (it basically works), but needs more qualification testing
• Battery powered RTC (from the PMIC) basically works, but a kernel driver is not yet available; the RTC included in the DM814x/AM387x processor has a proper kernel driver, but is not battery powered.

Rel. 2.0.0

• Release date: September 2012
• Status: released only as Release Candidate version
• EZSDK version: 5.04
• Supported carrier boards: NaonEVB-Lite, NaonEVB-Mid

Notes

• Added support for NaonEVB-Mid
• Added support for the following interfaces/features
  • Nand 8-bit
  • USB Host
  • USB OTG (NaonEVB-Mid only)
  • Video Input port VIN0 (NaonEVB-Mid only)
• Extended root file system with Angstrom repository (see below)
• NAND is working, but needs more testing

Notes on U-Boot bootloader

• Added Marvell Phy Gigabit support in U-Boot ver 2.0.0
• New env variables select the primary phy and link speed negotiation:

cpsw [0|1] : if present, select primary phy for networking operations in uboot

                  0 = phy 6 -> 100Mbit Naon module

                  1 = phy 1 -> 1Gbit external, EVB-Lite and EVB-Mid

giga [on] : if present, select gigabit speed on gigabit link, if not present speed link is default 100Mbit

NELK 2.0.0 root file system package list

The root file system provided with this release has been extended using opkg and the Angstrom repositories (see Uses_cases_with_Naon_Embedded_Linux_Kit#Extending_the_root_file_system for more information). Please refer to NELK 2.0.0 root file system package list (NAON) for a full list of the installed packages.

Rel. 1.0.0

• Release date: May 2012
• Status: obsolete
• EZSDK version: 5.03
• Supported carrier boards: NaonEVB-Lite only

Notes

• Initial release
• Supported interfaces/features:
  • SPI NOR Flash (boot)
  • EEPROM
  • Keypad controller
  • Touch screen controller
  • ADC
  • EMAC0 RMII (Fast Ethernet)
  • EMAC1 RGMII (Gigabit Ethernet)
  • SD/MMC1
  • Video Output port VOUT0 (24 bit)
  • UART0 (2-wire)
  • SPI0 (boot flash)
  • I2C0
  • I2C1 (DDC HDMI)
  • I2C2
  • HDMI
  • GPIO
  • SGX 3D accelerator
  • HDVICP2 codec engine