3,260
edits
Changes
m
== Rel. 3.0.0 ==
* Release date: December 2012* Status: released* EZSDK version: 5== Rel.05* Supported carrier boards: NaonEVB-Lite, NaonEVB-Mid1.0.0 ==
=== Notes === * Added support for the following interfaces/features** Video Input port VIN1 (additional host required)** SATA** [[NELK Power Management|Suspend to RAM]]** [[NELK Power Management|OPP Support]]** [[:Category:DWM|DWM]] (Wireless add-on module) on SDIO ([[:Category:NaonEVB-Lite|NaonEVB-Lite]] only)* NAND is supported (it basically works), but needs more qualification testing* Battery powered RTC (from the PMIC) basically works, but a kernel driver is not yet available; the RTC included in the DM814x/AM387x processor has a proper kernel driver, but is not battery powered. == Rel. 4.0.0 == * Release date: April 2013May 2012* Status: plannedobsolete* EZSDK version: 5.05.02.0003* Supported carrier boards: NaonEVB-Lite, NaonEVB-Midonly
→Notes
{{InfoBoxTop}}
{{AppliesToNaonAppliesToNaonFamily}}
{{Applies To NaonEVB-Lite}}
{{Applies To NaonEVB-Mid}}
=Naon Embedded Linux Kit (NELK) Release Notes=
{{ImportantMessage|text=HotFixes are modification introduced to software components (u-boot, kernel, ...) after a major NELK release. Customers can keep their source trees in sync and up to date with '''DAVE Embeddded Systems''' repositories using GIT, as described in [[How_to_update_NELK#Synchronizing_the_repository | Synchronizing_the_repository]]}} == Rel. 4.1.1 == * Release date: March 2014* Status: released* EZSDK version: 5.05.02.00* Supported carrier boards: NaonEVB-Lite, NaonEVB-Mid === Notes === * Maintenance release ==== HotFix list ==== ===== U-Boot =====* Enable Maya module ID pins as GPIO* Fixed MT47H64M16HR timings* Fixed NAND protocol issue with Spansion chip* Cleanup DDR2/3 initialization ===== Kernel ===== * Updated Naon and Dido defconfigs* Fixed UART3/UART5 clock issue* Fixed NAND protocol issue with Spansion chip == Rel. 4.0.0 == * Release date: April 2013* Status: released* EZSDK version: 5.05.02.00* Supported carrier boards: NaonEVB-Lite, NaonEVB-Mid === Notes === * Added support for Maya and Dido SOMs* Added support for the following interfaces/features** PMIC RTC (battery powered)** /proc/ti81xx_cpuinfo entry** Passing the mac address from u-boot to Linux kernel (command line parameters : eth0=xx:xx:xx:xx:xx:xx eth1=xx:xx:xx:xx:xx:xx)** Updated Memory Map** Dido 2GiB RAM** PCI Express on Dido** CPSW mode selection (dual emac vs switch) on u-boot ==== HotFix list ==== ===== U-Boot =====* 4.0. 1** TPS65910 IRQ GPIO mux configured correctly for the whole Naon family * 4.0.2** Fix Warm and WDT Reset. When a Warm or WDT Reset is asserted, subsystems are not correctly reset, leading to malfunctioning (eg: HDVPSS firmware_load hangs). The fix introduces a cold reset when a Warm or WDT reset is recognized in 1st stage ===== Kernel ===== * 4.0.1** Fix SPI NOR flash addressing** Fix TPS65911 panic on suspend * 4.0.2** [[NELK_Power_Management#Standby_Support | Gate a clock]] when user chooses zero (0) as clock frequency == Rel. 3.0.0 ==
* Release date: May December 2012* Status: obsoletereleased* EZSDK version: 5.0305* Supported carrier boards: NaonEVB-Lite only, NaonEVB-Mid
=== Notes ===
* Initial release* Supported Added support for the following interfaces/features:** SPI NOR Flash Video Input port VIN1 (bootadditional host required)** EEPROMSATA** Keypad controller[[NELK Power Management|Suspend to RAM]]** Touch screen controller[[NELK Power Management|OPP Support]]** ADC** EMAC0 RMII [[:Category:DWM|DWM]] (Fast EthernetWireless add-on module)** EMAC1 RGMII on SDIO (Gigabit Ethernet)** SD/MMC1** Video Output port VOUT0 (24 bit)** UART0 (2[[:Category:NaonEVB-Lite|NaonEVB-wireLite]] only)** SPI0 NAND is supported (boot flashit basically works), but needs more qualification testing** I2C0** I2C1 Battery powered RTC (DDC HDMIfrom the PMIC)** I2C2** HDMI** GPIO** SGX 3D accelerator** HDVICP2 codec enginebasically works, but a kernel driver is not yet available; the RTC included in the DM814x/AM387x processor has a proper kernel driver, but is not battery powered.
== Rel. 2.0.0 ==
The root file system provided with this release has been extended using opkg and the Angstrom repositories (see [[Uses_cases_with_Naon_Embedded_Linux_Kit#Extending_the_root_file_system]] for more information). Please refer to [[NELK 2.0.0 root file system package list (NAON)]] for a full list of the installed packages.
=== Notes ===
* Added support for Maya and Dido SOMsInitial release* Added support for the following Supported interfaces/features:** PMIC RTC SPI NOR Flash (battery poweredboot)** EEPROM** Keypad controller** Touch screen controller** ADC** EMAC0 RMII (Fast Ethernet)** EMAC1 RGMII (Gigabit Ethernet)** SD/MMC1** Video Output port VOUT0 (24 bit)** UART0 (2-wire)** SPI0 (boot flash)** I2C0** I2C1 (DDC HDMI)** I2C2** HDMI** GPIO** SGX 3D accelerator** HDVICP2 codec engine
