Integration guide (Naon)

Info Box Applies to Naon

Contents

IntroductionEdit

This page provides useful information and resources to system designers in order to integrate Naon module in his/her application quickly. These information complement SoM-independent recommendations provided in the Carrier board design guidelines (SOM) page.

Several topics are covered, ranging from hardware issues to manufacturing aspects.

HardwareEdit

Reference designsEdit

Several schematics are available in order to accelerate the design of carrier board hosting Naon SOM. Please note that, even if these schematics are derived from tested real-world applications, they are provided "as is" and they might be modified in order to adapt to your specific application.

Following sections provides some additional information helping to understand schematics.

Available schematics:

• NaonEVB-Lite: NaonEVB-Lite#Schematics
• NaonEVB-Mid: NaonEVB-Mid#Schematics

Naon mating connectorsEdit

Compatible part numbers are FX8C-140P-SVx by Hirose. x depends on selected stacking height. For more details please see Hirose FX8C Series.

Boot sequenceEdit

Naon default boot sequence can be changed by optional external circuitry.

Carrier board design guidelinesEdit

This page provides general guidelines about how to implement carrier boards hosting SOM.

In the following sections further hardware guidelines valid for NAON are analyzed. The information provided here complete the Carrier board design guidelines for some specific interfaces.

Interfaces GuidelinesEdit

For interfaces not mentioned in this section, refer to the generic guidelines.

USBEdit

PCBEdit

Table listeb below integrates the general basic guidelines table

Parameter for USB Differential Pairs	Min	Typ	Max
Max traces length	-	-	14"

SATAEdit

PCBEdit

Table listeb below integrates the general basic guidelines table

Parameter for USB Differential Pairs	Min	Typ	Max
Intra pair matching(mils	-	-	10
Inter pair matching(mils	-	-	-
Max traces length	-	-	6"

LCD InterfaceEdit

PCBEdit

• Matching depends from Pixel Clock. As general rule, match lines at 500-800 mils
• Place series terminator near Naon Connector

VIN InterfaceEdit

PCBEdit

• Matching depends from Pixel Clock. As general rule, match lines at 500-800 mils
• Place series terminator near VIN source

RMII InterfaceEdit

This interface is a subset of the RGMII port.

SchematicEdit

• use a standard RMII PHY device that support 50MHz Clock input mode
• Set PHY address different from integrated PHY

SoftwareEdit

Software section of the integration guide is about software device support for Naon hardware peripherals on different OSes.

For additional information regarding lowlevel support and configuration take a look at PSP Porting guide on TI wiki

Pin Mux ConfigurationEdit

The first thing to do when adding/modifying a peripheral is configure correctly the internal Pin Mux:in fact, nearly every peripheral function can be attached to more than one pin and nearly every pin is shared between two or more peripheral.

Pin Mux is quite complex in Naon and, fortunately, a tool from TI can help: we suggest to download and install TI Pin Mux Utility from TI website. Software installation and generic usage documentation is available on this TI wiki page

Pin Mux Configuration in u-bootEdit

Due the fact the correct configuration of pin mux usually should be applied as soon as possible and that's better if pin mux is done is only one place, DAVE Embedded Systems chose to move all its initialization inside the startup code of U-Boot

Changing default pin mux configuration is just a matter of:

1. open TI Pin Mux configuration
2. load the Naon default configuration provided by DAVE Embedded Systems
3. change the mux as needed
4. export the generated source code into the U-Boot source tree
5. rebuild u-boot and update it on your Naon board

For an in-depth description of the above steps see Pin Mux Configuration in U-Boot (Naon) article.

UARTEdit

Additional UART on LinuxEdit

See the article Additional UART on Linux (Naon) for a step-by-step guide.

Change default U-Boot ConsoleEdit

See the article Change Default U-Boot Console (Naon) for more details.

SPIEdit

Additional SPI bus on LinuxEdit

Additional SPI peripheral on LinuxEdit

I2CEdit

Additional I2C peripheral on LinuxEdit

GPIOEdit

Using a pin as GPIO on LinuxEdit