How to configure the network interfaces

Info Box Applies to Axel Ultra Applies to Axel Lite Applies to AXEL ESATTA Applies to Bora Applies to BORA Xpress Applies to BORA Lite Applies to Diva

Introduction

For deploying an Embedded System, one of the most used configuration is the Network Interface configuration.

Once the Embedded Device is finally configured for stand-alone bootstrap, the network interface should be configured for reaching the device remotely via network connections like ssh, telnet, ftp, htpp, etc.

This Application Note briefly describes how it is possible to simply configure the network interfaces on SystemV (aka SysV) or systemd

Resources

For further details on network configuration, please refer - for example - to:

• Debian - The basic network configuration
• systemd network configuration

Examples

The following configuration assumptions are used in the paragraphs shown below:

• IP address range of the LAN network 192.168.1.0 - 192.168.1.255
• IP address of the gateway 192.168.1.254
• IP address of the PC 192.168.1.100

SysV

The configuration files for SysV can be found in pre-defined directorys as written here

Basically, for network configuration, it should be enough to properly configure the /etc/network/interfaces file.

# /etc/network/interfaces -- configuration file for ifup(8), ifdown(8)

Here below an example of configuration file:

Static IP address

The network interface is configured with a static IP address by creating the configuration entry in the /etc/network/interfaces file as the following:

auto eth0
iface eth0 inet static
 address 192.168.1.100
 netmask 255.255.255.0
 gateway 192.168.1.254

Dynamic IP addres (DHCP)

The network interface is configured - using a proper DHCP server on the network - by creating the configuration entry in the /etc/network/interfaces file as the following:

allow-hotplug eth0
iface eth0 inet dhcp

When the Linux kernel detects the physical interface eth0, the iface causes ifup to use DHCP to configure the interface.

DNS

If the resolvconf package is not installed, the DNS configuration can be done manually by editing the /etc/resolv.conf as the following:

nameserver 192.168.1.1

For example, it can be done on the command line echoing the string in this way:

root@axel-lite:~# echo "nameserver 192.168.1.1" > /etc/resolv.conf

loopback network interface

The following configuration entry in the /etc/network/interfaces file brings up the loopback network interface lo upon booting the system.

# The loopback interface
auto lo
iface lo inet loopback

This one always exists in the /etc/network/interfaces file.

systemd

The network configuration for systemd are basically found in the /etc/systemd/network/ directory.

The most simply way for configuring the network interface is to create/edit the file /etc/systemd/network/eth0.network as per the following paragraphs.

For more example and usage hints on systemd, please refer to our wiki page.

Static IP address

[Match]
Name=eth0

# Prevent the interface loading if the kernel boots from nfs
KernelCommandLine=!nfsroot

[Network]
Address=192.168.1.100
Gateway=192.168.1.254
DNS=192.168.1.1

Dynamic IP addres (DHCP)

The network interface is configured - using a proper DHCP server on the network - by using the DHCP key in the configuration file as the following:

[Match]
Name=eth0

# Prevent the interface loading if the kernel boots from nfs
KernelCommandLine=!nfsroot

[Network]
DHCP=yes

When systemd network starts, it tries to use a DHCP server present in the network to configure the interface.

DNS

The DNS key (in the configuration file) is used only if the ystemd-resolved service is enabled and the /etc/resolv.conf has a symbolic link to /run/systemd/resolve/stub-resolv.conf

ln -sf /run/systemd/resolve/stub-resolv.conf /etc/resolv.conf

loopback network interface

systemd contains native implementations of various tasks that need to be executed as part of the boot process.

For example, it sets the hostname or configures the loopback network device.