DESK-MX8M-L/Deployment/MAC Address programming

History
Version	Issue Date	Notes
1.0.0	Jun 2022	First release

MAC Address programming

Every network adapter has a Media Access Control address (usually shortened to MAC address). A MAC address is a six-byte identifying number permanently embedded in the firmware of the adapter, and is readable by the network and the operating system of the device on which the adapter is installed.

The address must follow the standards set by the Institute of Electrical and Electronics Engineers (IEEE), which sets computer networking standards.

The MAC address is a six-pair set of hexadecimal numbers, for example a1-c2-e3-44-5f-6d. Specifically, in Ethernet, the MAC address is known as the Ethernet Address, which is the unique ID serial number of the Ethernet device in one's computer. MAC Addresses are used in a Local Area Network (LAN) by computers to communicate with each other. Every adapter has a unique MAC address.

In this Application Note, we will describe how to use the i.MX eFuses for programming and using the MAC address(es).

Obtaining a MAC address

To obtain a MAC address for your organization, please refer to our Setting the MAC address wiki page with the overall information about this topic.

Permanent storage areas

Some SOCs provide programmable OTPs for security, MAC address, boot modes, etc. Usually, some of these are general-purpose registers and can be managed by the user.

In other cases, an external permanent storage device can be used for storing permanent settings like the MAC address: for the i.MX SoC product family, DAVE proposes to use the General Purposes eFuses (OTP blocks) on SoC itself for storing permanently the MAC address(es).

MAC address programming

MAC address configuration in u-boot

If the MAC address is not already programmed in the OTPs and the ethaddr u-boot variable is not set, u-boot assignes a random value (different at every power on cycle):

Net:
Warning: ethernet@30be0000 (eth0) using random MAC address - 6e:e5:6d:a2:ea:e5
eth0: ethernet@30be0000

If the ethaddr is set and saved in the u-boot environment, it's value is used as the MAC Address:

u-boot=> setenv ethaddr 00:50:C2:1E:AF:CB
u-boot=> saveenv
Saving Environment to MMC... Writing to MMC(1)... OK
u-boot=>

eFuse programming

U-Boot uses the fuse prog command for writing the MAC address into the eFuse. The MAC address should be divided in high 16 bit and low 32 bits, for example MAC address AB:CD:12:34:56:78:

fuse prog -y 9 0 0x12345678
fuse prog -y 9 1 0xABCD

In the following example the MAC address 00:50:c2:1e:af:cd is stored in the i.MX SOM:

• (in case of presence) clear the ethaddr u-boot variable

u-boot=> setenv ethaddr
u-boot=> saveenv
Saving Environment to MMC... Writing to MMC(1)... OK

• program the MAC address in the OPTs with the following commands:

u-boot=> fuse prog 9 0 c21eafcd
Programming bank 9 word 0x00000000 to 0xc21eafcd...
Warning: Programming fuses is an irreversible operation!
         This may brick your system.
         Use this command only if you are sure of what you are doing!

Really perform this fuse programming? <y/N>
y
u-boot=> fuse prog 9 1 0050
Programming bank 9 word 0x00000001 to 0x00000050...
Warning: Programming fuses is an irreversible operation!
         This may brick your system.
         Use this command only if you are sure of what you are doing!

Really perform this fuse programming? <y/N>
y
u-boot=>

If you want to write the eFuse value directly without confirmation, uses the -y parameter with the fuse prog command, as per the previous example:

u-boot=> fuse prog -y 9 0 c21eafcd
u-boot=> fuse prog -y 9 1 0050

At the next boot, the ethaddr value wil be read from the OPTs:

Warning: ethernet@30be0000 using MAC address from ROM
eth0: ethernet@30be0000
Fastboot: Normal
Normal Boot
Hit any key to stop autoboot:  0
u-boot=> print ethaddr
ethaddr=00:50:c2:1e:af:cd
u-boot=>

The warning message informs that the ethaddr is not present in the u-boot environment and it has been set using the value read from the OTPs. For clearing the warning, it is enough to save the environment with saveenv.

u-boot=> saveenv

Linux kernel MAC address

The MAC Address configured in u-boot is passed to the kernel which configures the eth0 and eth1 peripheral with the correct values:

root@desk-mx8mp:~# ifconfig
eth0      Link encap:Ethernet  HWaddr 00:50:c2:1e:af:cd
          UP BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

eth1      Link encap:Ethernet  HWaddr 00:50:c2:1e:af:cc
          UP BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)
          Interrupt:43

lo        Link encap:Local Loopback
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:65536  Metric:1
          RX packets:82 errors:0 dropped:0 overruns:0 frame:0
          TX packets:82 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:6220 (6.0 KiB)  TX bytes:6220 (6.0 KiB)

root@desk-mx8mp:~#