Building the Yocto BSP (BELK/BXELK)
As the structure of the BELK/BXELK is based on several tools, it is strongly recommended the reading of this document first to get an overview.
The instructions described by this document apply to the following kits:
- 1 Building the Yocto BSP
- 1.1 Quick reference
- 1.2 How to build the Yocto BSP images including the U-Boot binary file, the Linux kernel image, and the target root file system image
- 1.3 Building additional packages
Building the Yocto BSP[edit | edit source]
Quick reference[edit | edit source]
|Repository||BSP Manifest||Yocto BSP Layer|
|dave-image-devel||This image include tools for development/debugging|
|dave-image-networking||In addition |
As known, in addition to a bootloader and the o.s. kernel, an embedded Linux system needs a root file system to operate. The root file system must contain everything needed to support the Linux system (applications, settings, data, etc.). The root file system is the file system that is contained on the same partition on which the root directory is located. The Linux kernel, at the end of its startup stage, mounts the root file system on the configured root device and finally launches the
/sbin/init, the first user space process and "father" of all the other processes.
For more information on the Linux filesystem, please refer to http://www.thegeekstuff.com/2010/09/linux-file-system-structure/.
BELK/BXELK provides one (or more) pre-built root file system, that can be used during the evaluation/development/deployment cycle. For instance, the root file system included in the
bora-image-devel image is suited for the development phase, since it provides a relatively rich set of packages including tools and libraries used to debug the application code. The pre-built root file systems are located here:
Besides the pre-built root file systems, BELK/BXELK also provides a rich repository containing pre-built applications and libraries. These packages can be easily installed on the target by using the
smart tool. Please refer to this section for more details.
To generate the supported root file systems, the build of the Yocto BSP has to be run. The output of this process is an image containing the U-Boot binary file, the Linux kernel image, and the selected root file system image. The following sections describe in detail how to execute this operation.
For more general information regarding the Yocto build system, please refer the dedicated category page.
How to build the Yocto BSP images including the U-Boot binary file, the Linux kernel image, and the target root file system image[edit | edit source]
The following procedure requires the access to the DAVE Embedded Systems' git repositories. The access to such repositories is granted to development kit's owners only. Please refer to this page for detailed instructions on how to get it.
This process requires a lot of hardware resources in terms of disk storage, RAM, and processing power. For this reason, it also is recommended to consider the use of a physical machine. For more details on this topic, please refer to this document which talks about the advanced use of the Yocto build system.
Initialize the build environment[edit | edit source]
Before running the build, the environment must be initialized properly.
BELK/BXELK Yocto BSP uses git-repo tool to fetch all the required git repositories. To install it, please use the following commands:
dvdk@dvdk-vm:~/belk$ curl http://commondatastorage.googleapis.com/git-repo-downloads/repo-1 > repo dvdk@dvdk-vm:~/belk$ chmod a+x repo dvdk@dvdk-vm:~/belk$ ./repo init -u email@example.com:bora/bora-bsp.git -b bora-morty dvdk@dvdk-vm:~/belk$ ./repo sync dvdk@dvdk-vm:~/belk$ source bora-bsp-init-env.sh
unauthenticated git protocol error[edit | edit source]
Since March 15th, 2022, GitHub stopped accepting DSA keys. RSA keys uploaded after Nov 2, 2021 will work only with SHA-2 signatures.
The deprecated MACs, ciphers, and unencrypted Git protocol are permanently disabled.
Running the build[edit | edit source]
Please note that even the basic root file system requires a few hours to build on a mid/hi range desktop (4-6 cores, 8-12 GiB RAM) also depending on your Internet connection speed (all sources are fetched from the network). Nearly 20GiB of disk space is required for the build. The process may be slowed down significantly since the performances of a virtual machine are reduced if compared to the physical hardware. Thus, it's recommended to check the hardware capabilities of the host system and, when building with Yocto is required, to consider the following options:
- Migrating the build system to a physical machine
- Assuming that the host system has the required resources, extending the hardware capabilities of the default MVM (e.g. adding more cores and disk space).
Once completed the initialization phase, developers can launch the Yocto image build process with the following commands:
dvdk@dvdk-vm:~/belk/build$ bitbake <target-image-name>
<target-image-name> is one of the images listed in here.
Once the build process is completed, the resulting files (the U-Boot binaries, the Linux kernel image, the device tree blob, the .tar.gz compressed root file system image, etc.) will be available in
Generating the SDKs[edit | edit source]
After creating an image as described in the previous version, the corresponding SDK can be generated by issuing the following command:
bitbake <target-image-name> -c populate-sdk
<target-image-name> with one of the images listed in here.
Building additional packages[edit | edit source]
To build additional packages the user must first enter the directory where the
bora-bsp-init-env.sh is placed and source it
dvdk@dvdk-vm:~/belk$ source bora-bsp-init-env.sh dvdk@dvdk-vm:~/belk/build$
And then can run any of the bitbake command.
dvdk@dvdk-vm:~/belk/build$ bitbake memtester
The resulting packages (the default format is ipk) can be found inside build/tmp/deploy/rpm.
dvdk@dvdk-vm:~/belk/build$ ls -l tmp/deploy/rpm/cortexa9hf_neon/memtester* -rw-r--r-- 1 dvdk dvdk 10692 Sep 12 16:05 tmp/deploy/rpm/cortexa9hf_neon/memtester-4.3.0-r0.cortexa9hf_neon.rpm -rw-r--r-- 1 dvdk dvdk 27693 Sep 12 16:05 tmp/deploy/rpm/cortexa9hf_neon/memtester-dbg-4.3.0-r0.cortexa9hf_neon.rpm -rw-r--r-- 1 dvdk dvdk 2872 Sep 12 16:05 tmp/deploy/rpm/cortexa9hf_neon/memtester-dev-4.3.0-r0.cortexa9hf_neon.rpm -rw-r--r-- 1 dvdk dvdk 5903 Sep 12 16:05 tmp/deploy/rpm/cortexa9hf_neon/memtester-doc-4.3.0-r0.cortexa9hf_neon.rpm