Getting startedEdit
Kit Identification CodesEdit
The development kits (DESK, XELK, XUELK, BELK, etc.) are identified by a couple of codes:
- P/N Part Number identification code
- S/N Serial Number identification code
These codes are printed on a label sticked to the box containing the kit.
For example, the following picture shows such a label of an AXEL Ultra XELK (XELK-H-S) with Serial Number 0CFA
These codes are required to complete the registration process of the kit.
UnboxingEdit
Once you've received the kit, please open the box and check the kit contents with the packing list included in the box, using the table on this chapter as a reference.
The hardware components (SOM, carrier boards and display) are pre-assembled, as shown in the picture below:
VideoEdit
Kit ContentsEdit
Component | Description | Notes |
---|---|---|
BoraLite SOM (p/n DBTD4111I0R)
|
||
BoraXEVB BoraLite Adapter board | ||
BoraXEVB carrier board | ||
AC/DC Single Output Wall Mount adapter Output: +12V – 2.0 A |
||
microSDHC card with SD adapter and USB adapter |
Order codesEdit
Order code | Description |
---|---|
BTELK-L-S | This code refers to the default configuration detailed above |
microSD LayoutEdit
The microSD provided with the kit is used to store:
- a bootable partition (mmcblk0p1, vfat) containing:
- binary images (u-boot and kernel images)
- root file system partition (mmcblk0p2, ext4)
Boot mode selection - S5Edit
S5 is a dip-switch for the boot mode selection. The following table reports the available options and the related configurations:
S5.1 | S5.2 | S5.3 | S5.4 | S5.5 | S5.6 | S5.7 | S5.8 | |
---|---|---|---|---|---|---|---|---|
SPI-NOR | OFF | ON | OFF | ON | ON | ON | ON | OFF |
SD-card | OFF | ON | OFF | ON | ON | OFF | ON | OFF |
NAND (*) | OFF | ON | OFF | ON | ON | OFF | ON | ON |
JTAG | OFF | ON | OFF | ON | ON | ON | ON | ON |
(*) Boot mode from NAND in supported ONLY on BORA Lite SOM module
Reset button - S6Edit
S6 is the hardware reset button connected to the MRSTn signal (J2.16 SOM connector)
General InformationEdit
Product HighlightsEdit
The BORA Lite Evaluation Board platform presented here provides a compact solution for evaluating the BORA Lite SOM performances and connection capability.
The following table summarizes the main hardware and software features available with BoraXEVB:
HardwareEdit
Subsystem | Characteristics |
---|---|
CPU | Zynq 7000 Dual Core Cortex-A7 |
SD | microSD boot device |
USB | OTG |
Serial Ports | RS232 CAN interface |
Ethernet | Dual EMAC 10/100/1000Mbps |
Display | LVDS interface |
Touchscreen | Resistive |
Espansion | FMC connector |
PSU | 12 to 24V DC |
SoftwareEdit
Subsystem | Options |
---|---|
Operating System | Linux |
Distribution | Yocto, Petalinux |
Applications | SoftPLC |
Block DiagramEdit
The following picture shows BORA Xpress EVB block diagram:
Configurable routing optionsEdit
FPGA banks #12, #34 and #35 supports different routing options as shown in the following picture.
For a detailed description of FMC connector routing, please refer to this section.
BoraXEdit
Bora LiteEdit
Interfaces and ConnectorsEdit
Power SupplyEdit
Power supply - JP2Edit
Power is provided through the JP2 connector.
JP2 connector is a standard 2.1mm/5.5mm DC power jack with positive center pin
Pin# | Pin name | Function | Notes |
---|---|---|---|
1 | VIN | Power supply | Nominal: +12V |
2 , 3 | DGND | Ground | - |
CPU connectorsEdit
SoM's signals mappingEdit
Bora LiteEdit
As known, Bora Lite requires an adapter to be mounted on the BoraXEVB carrier board. The adapter swap some signals to allow to use some carrier board peripherals routed on unavailable pins of the SoM. For this reason, it can be tricky to find out where the SoM's signals are routed at the carrier board level. The following table details such routing for PL banks. Here it is assumed to use an adapter with default mounting options.
SoM's signal | Routing options at carrier board level | ||||||
---|---|---|---|---|---|---|---|
Bank | Name | Option #1
(default) |
Option #2 | ||||
Name | Pin | Note | Name | Pin | Note | ||
34 | IO_0_34 | IO_0_VRN_34 | J31.2 | Header | |||
J27D.H2 | FMC conn. | ||||||
IO_25_34 | IO_25_VRP_35 | J31.4 | Header | ||||
J27B.D1 | FMC conn. | ||||||
IO_L10N_T1_34 | IO_L10N_T1_34 | J27D.H26 | FMC conn. | ||||
IO_L10P_T1_34 | IO_L10P_T1_34 | J27D.H25 | FMC conn. | ||||
IO_L11N_T1_SRCC_34 | IO_L11N_T1_SRCC_34 | J27D.G3 | FMC conn. | ||||
IO_L11P_T1_SRCC_34 | IO_L11P_T1_SRCC_34 | J27D.G2 | FMC conn. | ||||
IO_L12N_T1_MRCC_34 | IO_L12N_T1_MRCC_34 | J27D.H5 | FMC conn. | ||||
IO_L12P_T1_MRCC_34 | IO_L12P_T1_MRCC_34 | J27D.H4 | FMC conn. | ||||
IO_L13N_T2_MRCC_34 | IO_L13N_T1_MRCC_34 | J27D.G7 | FMC conn. | ||||
IO_L13P_T2_MRCC_34 | IO_L13P_T1_MRCC_34 | J27D.G6 | FMC conn. | ||||
IO_L14N_T2_SRCC_34 | IO_L14N_T2_SRCC_34 | J27B.D9 | FMC conn. | ||||
IO_L14P_T2_SRCC_34 | IO_L14P_T2_SRCC_34 | J27B.D8 | FMC conn. | ||||
IO_L15N_T2_DQS_34 | IO_L15N_T2_DQS_34 | J27B.D21 | FMC conn. | ||||
IO_L15P_T2_DQS_34 | IO_L15P_T2_DQS_34 | J27B.D20 | FMC conn. | ||||
IO_L16N_T2_34 | IO_L16N_T2_34 | J27B.C23 | FMC conn. | ||||
IO_L16P_T2_34 | IO_L16P_T2_34 | J27B.C22 | FMC conn. | ||||
IO_L17N_T2_34 | IO_L17N_T2_34 | J27D.G22 | FMC conn. | ||||
IO_L17P_T2_34 | IO_L17P_T2_34 | J27D.G21 | FMC conn. | ||||
IO_L18N_T2_34 | IO_L18N_T2_34 | J27D.H20 | FMC conn. | ||||
IO_L18P_T2_34 | IO_L18P_T2_34 | J27D.H19 | FMC conn. | ||||
IO_L19N_T3_VREF_34 | IO_L19N_T3_VREF_34 | J27D.G19 | FMC conn. | ||||
TP21 | TP SMD | ||||||
IO_L19P_T3_34 | n/a | n/a | At the adapter level, this signal (as CAN_RX) is connected to a CAN transceiver. The CAN bus is available at J24. | ||||
IO_L1N_T0_34 | IO_L1N_T0_34 | J27B.C19 | FMC conn. | ||||
IO_L1P_T0_34 | IO_L1P_T0_34 | J27B.C18 | FMC conn. | ||||
IO_L20N_T3_34 | IO_L20N_T3_34 | J27B.D18 | FMC conn. | ||||
IO_L20P_T3_34 | IO_L20P_T3_34 | J27B.D17 | FMC conn. | ||||
IO_L21N_T3_DQS_34 | IO_L21N_T3_DQS_34 | J27D.H17 | FMC conn. | ||||
IO_L21P_T3_DQS_34 | IO_L21P_T3_DQS_34 | J27D.H16 | FMC conn. | ||||
IO_L22N_T3_34 | IO_L22N_T3_34 | J27D.G16 | FMC conn. | ||||
IO_L22P_T3_34 | IO_L22P_T3_34 | J27D.G15 | FMC conn. | ||||
IO_L23N_T3_34 | IO_L23N_T3_34 | J27B.C11 | FMC conn. | ||||
IO_L23P_T3_34 | IO_L23P_T3_34 | J27B.C10 | FMC conn. | ||||
IO_L24N_T3_34 | IO_L24N_T3_34 | J27D.H23 | FMC conn. | ||||
IO_L24P_T3_34 | IO_L24P_T3_34 | J27D.H22 | FMC conn. | ||||
IO_L2N_T0_34 | IO_L2N_T0_34 | J27B.C15 | FMC conn. | ||||
IO_L2P_T0_34 | IO_L2P_T0_34 | J27B.C14 | FMC conn. | ||||
IO_L3N_T0_DQS_34 | IO_L3N_T0_DQS_34 | J27D.G13 | FMC conn. | ||||
IO_L3P_T0_DQS_PUDC_B_34
(10K pull-up on SoM) |
IO_L3P_T0_DQS_PUDC_B_34 | J27D.G12 | FMC conn. | ||||
IO_L4N_T0_34 | IO_L4N_T0_34 | J27D.G10 | FMC conn. | ||||
IO_L4P_T0_34 | IO_L4P_T0_34 | J27D.G9 | FMC conn. | ||||
IO_L5N_T0_34 | IO_L5N_T0_34 | J27D.H11 | FMC conn. | ||||
IO_L5P_T0_34 | IO_L5P_T0_34 | J27D.H10 | FMC conn. | ||||
IO_L6N_T0_VREF_34 | IO_L6N_T0_VREF_34 | J27B.D15 | FMC conn. | ||||
TP22 | TP SMD | ||||||
IO_L6P_T0_34 | n/a | n/a | At the adapter level, this signal (as CAN_TX) is connected to a CAN transceiver. The CAN bus is available at J24. | ||||
IO_L7N_T1_34 | IO_L7N_T1_34 | J27D.H8 | FMC conn. | ||||
IO_L7P_T1_34 | IO_L7P_T1_34 | J27D.H7 | FMC conn. | ||||
IO_L8N_T1_34 | IO_L8N_T1_34 | J27D.H14 | FMC conn. | ||||
IO_L8P_T1_34 | IO_L8P_T1_34 | J27D.H13 | FMC conn. | ||||
IO_L9N_T1_DQS_34 | IO_L9N_T1_DQS_34 | J27B.D12 | FMC conn. | ||||
IO_L9P_T1_DQS_34 | IO_L9P_T1_DQS_34 | J27B.D11 | FMC conn. | ||||
35 | IO_0_35 | IO_0_VRN_35 | J27C.F1 | FMC conn. | |||
J31.1 | Header | ||||||
IO_25_35 | IO_25_VRP_35 | J27E.K13 | FMC conn. | ||||
J31.3 | Header | ||||||
IO_L10N_T1_AD11N_35 | IO_L10N_T1_AD11N_35 | J27D.G34 | FMC conn. | FPGA_BANK35_AD11N | JP32.3 | Header | |
IO_L10P_T1_AD11P_35 | IO_L10P_T1_AD11P_35 | J27D.G33 | FMC conn. | FPGA_BANK35_AD11P | JP32.1 | Header | |
IO_L11N_T1_SRCC_35 | IO_L11N_T1_SRCC_35 | J27E.J3 | FMC conn. | ||||
IO_L11P_T1_SRCC_35 | IO_L11P_T1_SRCC_35 | J27E.J2 | FMC conn. | ||||
IO_L12N_T1_MRCC_35 | IO_L12N_T1_MRCC_35 | J27E.K5 | FMC conn. | ||||
IO_L12P_T1_MRCC_35 | IO_L12P_T1_MRCC_35 | J27E.K4 | FMC conn. | ||||
IO_L13N_T2_MRCC_35 | IO_L13N_T2_MRCC_35 | J27C.F5 | FMC conn. | ||||
IO_L13P_T2_MRCC_35 | IO_L13P_T2_MRCC_35 | J27C.F4 | FMC conn. | ||||
IO_L14N_T2_AD4N_SRCC_35 | IO_L14N_T2_AD4N_SRCC_35 | J27C.E3 | FMC conn. | FPGA_BANK35_AD4N | JP30.16 | Header | |
IO_L14P_T2_AD4P_SRCC_35 | IO_L14P_T2_AD4P_SRCC_35 | J27C.E2 | FMC conn. | FPGA_BANK35_AD4P | JP30.14 | Header | |
IO_L15N_T2_DQS_AD12N_35 | IO_L15N_T2_DQS_AD12N_35 | J27D.H38 | FMC conn. | FPGA_BANK35_AD12N | JP32.8 | Header | |
IO_L15P_T2_DQS_AD12P_35 | IO_L15P_T2_DQS_AD12P_35 | J27D.H37 | FMC conn. | FPGA_BANK35_AD12P | JP32.6 | Header | |
IO_L16N_T2_35 | IO_L16N_T2_35 | J27D.G37 | FMC conn. | ||||
IO_L16P_T2_35 | IO_L16P_T2_35 | J27D.G36 | FMC conn. | ||||
IO_L17N_T2_AD5N_35 | IO_L17N_T2_AD5N_35 | J27E.K8 | FMC conn. | FPGA_BANK35_AD5N | JP31.1 | Header | |
IO_L17P_T2_AD5P_35 | IO_L17P_T2_AD5P_35 | J27E.K7 | FMC conn. | FPGA_BANK35_AD5P | JP30.15 | Header | |
IO_L18N_T2_AD13N_35 | IO_L18N_T2_AD13N_35 | J27E.J7 | FMC conn. | FPGA_BANK35_AD13N | JP32.9 | Header | |
IO_L18P_T2_AD13P_35 | IO_L18P_T2_AD13P_35 | J27E.J6 | FMC conn. | FPGA_BANK35_AD13P | JP32.7 | Header | |
IO_L19N_T3_VREF_35 | IO_L19N_T3_VREF_35 | J27C.F8 | FMC conn. | ||||
TP24 | TP SMD | ||||||
IO_L19P_T3_35 | IO_L19P_T3_35 | J27C.F7 | FMC conn. | ||||
IO_L1N_T0_AD0N_35 | IO_L1N_T0_AD0N_35 | J27D.G25 | FMC conn. | FPGA_BANK35_AD0P | JP30.4 | Header | |
IO_L1P_T0_AD0P_35 | IO_L1P_T0_AD0P_35 | J27D.G24 | FMC conn. | FPGA_BANK35_AD0N | JP30.2 | Header | |
IO_L20N_T3_AD6N_35 | IO_L20N_T3_AD6N_35 | J27C.E7 | FMC conn. | FPGA_BANK35_AD6N | JP31.6 | Header | |
IO_L20P_T3_AD6P_35 | IO_L20P_T3_AD6P_35 | J27C.E6 | FMC conn. | FPGA_BANK35_AD6P | JP31.4 | Header | |
IO_L21N_T3_DQS_AD14N_35 | IO_L21N_T3_DQS_AD14N_35 | J27E.K11 | FMC conn. | FPGA_BANK35_AD14N | JP32.14 | Header | |
IO_L21P_T3_DQS_AD14P_35 | IO_L21P_T3_DQS_AD14P_35 | J27E.K10 | FMC conn. | FPGA_BANK35_AD14P | JP32.12 | Header | |
IO_L22N_T3_AD7N_35 | IO_L22N_T3_AD7N_35 | J27E.J10 | FMC conn. | FPGA_BANK35_AD7N | JP31.7 | Header | |
IO_L22P_T3_AD7P_35 | IO_L22P_T3_AD7P_35 | J27E.J9 | FMC conn. | FPGA_BANK35_AD7P | JP31.5 | Header | |
IO_L23N_T3_35 | IO_L23N_T3_35 | J27C.F11 | FMC conn. | ||||
IO_L23P_T3_35 | IO_L23P_T3_35 | J27C.F10 | FMC conn. | ||||
IO_L24N_T3_AD15N_35 | IO_L24N_T3_AD15N_35 | J27C.E10 | FMC conn. | FPGA_BANK35_AD15N | JP32.15 | Header | |
IO_L24P_T3_AD15P_35 | IO_L24P_T3_AD15P_35 | J27C.E9 | FMC conn. | FPGA_BANK35_AD15P | JP32.13 | Header | |
IO_L2N_T0_AD8N_35 | IO_L2N_T0_AD8N_35 | J27B.D24 | FMC conn. | FPGA_BANK35_AD8N | JP31.12 | Header | |
IO_L2P_T0_AD8P_35 | IO_L2P_T0_AD8P_35 | J27B.D23 | FMC conn. | FPGA_BANK35_AD8P | JP31.10 | Header | |
IO_L3N_T0_DQS_AD1N_35 | IO_L3N_T0_DQS_AD1N_35 | J27D.H29 | FMC conn. | FPGA_BANK35_AD1N | JP30.5 | Header | |
IO_L3P_T0_DQS_AD1P_35 | IO_L3P_T0_DQS_AD1P_35 | J27D.H28 | FMC conn. | FPGA_BANK35_AD1P | JP30.3 | Header | |
IO_L4N_T0_35 | IO_L4N_T0_35 | J27D.G28 | FMC conn. | ||||
IO_L4P_T0_35 | IO_L4P_T0_35 | J27D.G27 | FMC conn. | ||||
IO_L5N_T0_AD9N_35 | IO_L5N_T0_AD9N_35 | J27B.D27 | FMC conn. | FPGA_BANK35_AD9N | JP31.13 | Header | |
IO_L5P_T0_AD9P_35 | IO_L5P_T0_AD9P_35 | J27B.D26 | FMC conn. | FPGA_BANK35_AD9P | JP31.11 | Header | |
IO_L6N_T0_VREF_35 | IO_L6N_T0_VREF_35 | J27B.C27 | FMC conn. | ||||
TP23 | TP SMD | ||||||
IO_L6P_T0_35 | IO_L6P_T0_35 | J27B.C26 | FMC conn. | ||||
IO_L7N_T1_AD2N_35 | IO_L7N_T1_AD2N_35 | J27D.H32 | FMC conn. | FPGA_BANK35_AD2N | JP30.10 | Header | |
IO_L7P_T1_AD2P_35 | IO_L7P_T1_AD2P_35 | J27D.H31 | FMC conn. | FPGA_BANK35_AD2P | JP30.8 | Header | |
IO_L8N_T1_AD10N_35 | IO_L8N_T1_AD10N_35 | J27D.G31 | FMC conn. | FPGA_BANK35_AD10N | JP32.2 | Header | |
IO_L8P_T1_AD10P_35 | IO_L8P_T1_AD10P_35 | J27D.G30 | FMC conn. | FPGA_BANK35_AD10P | JP31.16 | Header | |
IO_L9N_T1_DQS_AD3N_35 | IO_L9N_T1_DQS_AD3N_35 | J27D.H35 | FMC conn. | FPGA_BANK35_AD3N | JP30.11 | Header | |
IO_L9P_T1_DQS_AD3P_35 | IO_L9P_T1_DQS_AD3P_35 | J27D.H34 | FMC conn. | FPGA_BANK35_AD3P | JP30.9 | Header | |
13
(not available on Zynq 7007S and 7010) |
IO_L11P_T1_SRCC_13 | IO_L23P_T3_13 | JP17.3 | PMOD [A] | |||
IO_L11N_T1_SRCC_13 | IO_L23N_T3_13 | JP17.4 | PMOD [A] | ||||
IO_L12P_T1_MRCC_13 | IO_L9P_T1_DQS_13 | JP17.2 | PMOD [A] | IO_L9P_T1_DQS_13 | J30.1 | ONE PIECE | |
IO_L12N_T1_MRCC_13 | IO_L9N_T1_DQS_13 | JP17.1 | PMOD [A] | IO_L9N_T1_DQS_13 | J30.3 | ONE PIECE | |
IO_L13P_T2_MRCC_13 | IO_L7P_T1_13 | JP17.7 | PMOD [A] | IO_L7P_T1_13 | J30.24 | ONE PIECE | |
IO_L13N_T2_MRCC_13 | IO_L7N_T1_13 | JP17.8 | PMOD [A] | IO_L7N_T1_13 | J30.26 | ONE PIECE | |
IO_L14P_T2_SRCC_13 | IO_L15P_T2_DQS_13 | n/a | ETH1_RXCK | IO_L15P_T2_DQS_13 | J30.25 | ONE PIECE | |
IO_L14N_T2_SRCC_13 | IO_L15N_T2_DQS_13 | n/a | ETH1_RXCTL | IO_L15N_T2_DQS_13 | J30.27 | ONE PIECE | |
IO_L15P_T2_DQS_13 | IO_L5P_T0_13 | JP17.6 | PMOD [A] | IO_L5P_T0_13 | J30.20 | ONE PIECE | |
IO_L15N_T2_DQS_13 | IO_L5N_T0_13 | JP17.5 | PMOD [A] | IO_L5N_T0_13 | J30.18 | ONE PIECE | |
IO_L16N_T2_13 | IO_L16N_T2_13 | n/a | ETH1_TXCTL | IO_L16N_T2_13 | J30.31 | ONE PIECE | |
IO_L16P_T2_13 | IO_L16P_T2_13 | n/a | ETH1_TXCK | IO_L16P_T2_13 | J30.29 | ONE PIECE | |
IO_L17N_T2_13 | IO_L17N_T2_13 | n/a | ETH1_RXD1 | IO_L17N_T2_13 | J30.35 | ONE PIECE | |
IO_L17P_T2_13 | IO_L17P_T2_13 | n/a | ETH1_RXD0 | IO_L17P_T2_13 | J30.33 | ONE PIECE | |
IO_L18N_T2_13 | IO_L18N_T2_13 | n/a | ETH1_RXD3 | IO_L18N_T2_13 | J30.39 | ONE PIECE | |
IO_L18P_T2_13 | IO_L18P_T2_13 | n/a | ETH1_RXD2 | IO_L18P_T2_13 | J30.37 | ONE PIECE | |
IO_L19N_T3_VREF_13 | IO_L19N_T3_VREF_13 | n/a | ETH1_TXD1 | IO_L19N_T3_VREF_13 | J30.43 | ONE PIECE | |
IO_L19P_T3_13 | IO_L19P_T3_13 | n/a | ETH1_TXD0 | IO_L19P_T3_13 | J30.41 | ONE PIECE | |
IO_L20N_T3_13 | IO_L20N_T3_13 | n/a | ETH1_TXD3 | IO_L20N_T3_13 | J30.47 | ONE PIECE | |
IO_L20P_T3_13 | IO_L20P_T3_13 | n/a | ETH1_TXD2 | IO_L20P_T3_13 | J30.45 | ONE PIECE | |
IO_L21N_T3_DQS_13 | IO_L21N_T3_DQS_13 | n/a | ETH1_MDC | IO_L21N_T3_DQS_13 | J30.51 | ONE PIECE | |
IO_L21P_T3_DQS_13 | IO_L21P_T3_DQS_13 | n/a | ETH1_MDIO | IO_L21P_T3_DQS_13 | J30.49 | ONE PIECE | |
IO_L22N_T3_13 | IO_L22N_T3_13 | IO_L22N_T3_13 | J30.55 | ONE PIECE | |||
IO_L22P_T3_13 | IO_L22P_T3_13 | n/a | DWM_WIFI_IRQ | IO_L22P_T3_13 | J30.53 | ONE PIECE | |
IO_L6N_T0_VREF_13 | IO_L6N_T0_VREF_13 | JP23.3 | PMOD [B] | IO_L6N_T0_VREF_13 | J30.30 | ONE PIECE | |
n/a | USB1_OC |
Edit
Some BoraXEVB signals are unavailable when it is mated with Bora Lite SoM. The following signals are not routed to the SoM due to the limited pin count of the SODIMM connector.
Bank | Carrier's signal |
---|---|
13 | IO_25_13 |
13 | IO_L1P_T0_13 |
13 | IO_L1N_T0_13 |
13 | IO_L2P_T0_13 |
13 | IO_L2N_T0_13 |
13 | IO_L3P_T0_DQS_13 |
13 | IO_L3N_T0_DQS_13 |
13 | IO_L4P_T0_13 |
13 | IO_L4N_T0_13 |
500 | NAND_CS0/SPI0_CS1 |
500 | NAND_IO3 |
500 | NAND_IO4 |
500 | NAND_IO5 |
500 | NAND_IO6 |
500 | NAND_IO7 |
500 | NAND_RD_B/VCFG1 |
500 | NAND_CLE/VCFG0 |
JTAGEdit
JTAGEdit
JTAG port is available as two different mechanical connectors:
- 2.00mm-pitch 7x2 header (Xilinx standard)
- 2.54mm-pitch 10x2 header (ARM standard): http://www2.lauterbach.com/pdf/arm_app_jtag.pdf
- This port is connected to Zynq's native JTAG signals. Please note that Zynq's internal JTAG chain supports differents configurations, depending on bootstrap signals. In case split mode is selected, CPU JTAG can be routed separately via PL. For more details please refer to Zynq Technical Reference Manual.
- JTAG on BORA Xpress EVB is also connected to the FMC connector. For more details on how to connect JTAG on a custom FMC card please refer to ANSI/VITA FPGA Mezzanine Card (FMC) Standard.
JTAG XILINX - J13Edit
J13 is a 14-pin 7x2x2 pitch vertical header. The following table reports the pinout of the connector:
Pin# | Pin name | Function | Notes |
---|---|---|---|
1, 3, 5, 7, 9, 11, 13 | DGND | - | - |
2 | 3.3V | - | - |
4 | JTAG_TMS | - | - |
6 | JTAG_TCK | - | - |
8 | JTAG_TDO | - | - |
10 | JTAG_TDI | - | - |
12 | N.C. | - | - |
14 | JTAG_TRSTn | - | - |
JTAG ARM - J18Edit
J18 is a 20-pin 10x2x2.54 pitch vertical header. The following table reports the pinout of the connector:
Pin# | Pin name | Function | Notes |
---|---|---|---|
1 | 3.3V | - | - |
2 | 3.3V | - | - |
3, 11, 17, 19 | N.C. | - | - |
4, 6 ,8 ,10 ,12, 14, 16, 18, 20 |
DGND | - | - |
5 | JTAG_TDI | - | - |
7 | JTAG_TMS | - | - |
9 | JTAG_TCK | - | - |
13 | JTAG_TDO | - | - |
15 | JTAG_TRSTn | - | - |
EthernetEdit
Ethernet port #0 (ETH0) - J8Edit
J8 is a RJ45 Gigabit Ethernet connector - incorporating magnetics - connected to the Bora Xpress integrated ethernet controller and PHY.
Pin# | Pin name | Function | Notes |
---|---|---|---|
1 | CT_TRD3 | center tap TRD3 | - |
2 | ETH_TXRX2_M | - | - |
3 | ETH_TXRX2_P | - | - |
4 | ETH_TXRX1_P | - | - |
5 | ETH_TXRX1_M | - | - |
6 | CT_TRD2 | center tap TRD2 | - |
7 | CT_TRD4 | center tap TRD4 | - |
8 | ETH_TXRX3_P | - | - |
9 | ETH_TXRX3_M | - | - |
10 | ETH_TXRX0_M | - | - |
11 | ETH_TXRX0_P | - | - |
12 | CT_TRD1 | center tap TRD1 | - |
13 | 3.3V_ETH0_LED2 | - | - |
15 | 3.3V_ETH0_LED1 | - | - |
14, 16 | +3.3V | - | - |
Ethernet port #1 (ETH1) - J9Edit
J9 is a RJ45 Gigabit Ethernet connector - incorporating magnetics - connected to Micrel KSZ9031 PHY (Gigabit Ethernet Transceiver). This, in turn, is connected to PL's bank 13 via RGMII interface. This is an example of EMIO routing showing how to route PS's MAC signals via PL subsystem.
Pin# | Pin name | Function | Notes |
---|---|---|---|
1 | CT_TRD3 | center tap TRD3 | - |
2 | ETH1_TXRX2_M | - | - |
3 | ETH1_TXRX2_P | - | - |
4 | ETH1_TXRX1_P | - | - |
5 | ETH1_TXRX1_M | - | - |
6 | CT_TRD2 | center tap TRD2 | - |
7 | CT_TRD4 | center tap TRD4 | - |
8 | ETH1_TXRX3_P | - | - |
9 | ETH1_TXRX3_M | - | - |
10 | ETH1_TXRX0_M | - | - |
11 | ETH1_TXRX0_P | - | - |
12 | CT_TRD1 | center tap TRD1 | - |
13 | 3.3V_ETH1_LED2 | - | - |
15 | 3.3V_ETH1_LED1 | - | - |
14, 16 | +3.3V | - | - |
ConsoleEdit
UART1 - J17Edit
J17 is a standard DB9 connector that routes the signals coming from the RS232 transceiver that is connected to the PS MIO signals of the UART1 port.
Pin# | Pin name | Function | Notes |
---|---|---|---|
1, 6, 4, 9 | N.C. | N.C. | |
2 | UART_EXT_RX | Receive line | Connected to protection diode array |
3 | UART_EXT_TX | Transmit line | Connected to protection diode array |
5 | DGND | Ground | |
7, 8 | N.C. | N.C. | Connected to protection diode array |
SDEdit
MicroSD - J21Edit
J21 is a microSD memory card connector. It is connected to the BORA Xpress SOM through a bidirectional 1.8V/3.3V voltage-level translator mounted on the BORA Xpress EVB. Level shifter is required because MIO signals are 1.8V. The following table reports the pinout of the connector:
Pin# | Pin name | Function | Notes |
---|---|---|---|
1 | PS_SD0_DAT2 | - | - |
2 | PS_SD0_DAT3 | - | - |
3 | PS_SD0_CMD | - | - |
4 | 3.3V | - | - |
5 | PS_SD0_CLK | - | - |
6, 9, 10, 11, 12 | DGND | - | - |
7 | PS_SD0_DAT0 | - | - |
8 | PS_SD0_DAT1 | - | - |
3.3V | - | Pull up to 3.3V with 10K Ohm - |
USBEdit
USB OTG - J19Edit
J19 is a standard USB MICRO AB connector. It is connected to the BORA Xpress USB 2.0 OTG peripheral. The following table reports the pinout of the connector:
Pin# | Pin name | Function | Notes |
---|---|---|---|
1 | USB_OTG_VBUS | - | - |
2 | USBM1 | - | - |
3 | USBP1 | - | - |
4 | OTG_ID | - | - |
5 | USB_OTG_DGND | - | - |
6, 7, 8, 9 | USB_OTG_SHIELD | - | - |
LVDSEdit
LVDS - J26Edit
J26 is a vertical double row straight 20-pin 1.25mm pitch header. This interface shows how to implement a differential connection to an LCD screen. As known, Zynq does not implement an LCD controller, however this can be integrated in FPGA fabric as shown by this example: https://wiki.analog.com/resources/tools-software/linux-drivers/platforms/zynq. The following table reports the pinout of the connector:
Pin# | Pin name | Function | Notes |
---|---|---|---|
1, 2 | 3.3V_LCD | - | - |
3, 4, 7, 10, 13, 16, 19 |
DGND | Ground | - |
5 | LCD_LVDS_D0- | - | - |
6 | LCD_LVDS_D0+ | - | - |
8 | LCD_LVDS_D1- | - | - |
9 | LCD_LVDS_D1+ | - | - |
11 | LCD_LVDS_D2- | - | - |
12 | LCD_LVDS_D2+ | - | - |
14 | LCD_LVDS_CLK- | - | - |
15 | LCD_LVDS_CLK+ | - | - |
17 | LCD_P17 | - | - |
18 | LCD_P18 | - | - |
20 | LCD_P20 | - | - |
21,22 | DGND | Ground | Shield |
TouchscreenEdit
Touch screen - J25Edit
J25 is a ZIF 4-pin 1.0mm pitch connector that connects the touchscreen drive lines to the touch screen controller on the BoORA Xpress EVB. The following table reports the pinout of the connector:
Pin# | Pin name | Function | Notes |
---|---|---|---|
1 | TSC_YP | - | - |
2 | TSC_XP | - | - |
3 | TSC_YM | - | - |
4 | TSC_XM | - | - |
CANEdit
CAN - J24Edit
J24 is a 10-pin 5x2x2.54mm pitch vertical header directly connected to BORA Xpress SoM's transceiver for the CAN interface. This 2.5mm-pitch header is compatible with commonly available IDC-10/DB9 flat cables. The following table reports the pinout of the connector:
Pin# | Pin name | Function | Notes |
---|---|---|---|
1, 6, 7, 8, 9, 10 |
N.C. | - | - |
2, 5 | CAN_SHIELD | - | - |
3 | CAN_L | - | - |
4 | CAN_H | - | - |
RTCEdit
FPGA, WatchDog, RTC, RST - JP22Edit
JP22 is a 16-pin 8x2x2.54 pitch vertical header. The following table reports the pinout of the connector:
Pin# | Pin name | Function | Notes |
---|---|---|---|
1 | FPGA_INIT_B | - | - |
2 | RTC_32KHZ | - | - |
3 | FPGA_PROGRAM_B | - | - |
4 | RTC_RST | - | - |
5 | FPGA_DONE | - | - |
6 | RTC_INT/SQW | - | - |
7, 8 | DGND | Ground | - |
9 | WD_SET0 | - | - |
10 | SYS_RSTn | - | - |
11 | WD_SET1 | - | - |
12 | PORSTn | - | - |
13 | WD_SET2 | - | - |
14 | MRSTn | - | - |
15 | PS_MIO15_500 | - | - |
16 | CB_PWR_GOOD | - | - |
WatchdogEdit
WatchDog Settings - S1, S2 and S3Edit
S1, S2 and S3 are dip-switch to override the default startup delay and timeout of the BORA Xpress module watchdog. For more details please refer to this page.
S1.1 | S1.2 | |
---|---|---|
WD_SET0 SOM default | OFF | OFF |
WD_SET0 = '1' | ON | OFF |
WD_SET0 = '0' | OFF | ON |
S2.1 | S2.2 | |
---|---|---|
WD_SET1 SOM default | OFF | OFF |
WD_SET1 = '1' | ON | OFF |
WD_SET1 = '0' | OFF | ON |
S3.1 | S3.2 | |
---|---|---|
WD_SET2 SOM default | OFF | OFF |
WD_SET2 = '1' | ON | OFF |
WD_SET2 = '0' | OFF | ON |
DWMEdit
DWM (DAVE Wifi/BT module) socket - J23Edit
J23 is a 52991-0308 connector type (30 pins, vertical, 0.50mm picth). This socket connects the DWM Wireless Module (optional) to the BORA Xpress EVB. The following table reports the pinout of the connector:
Pin# | Pin name | Function | Notes |
---|---|---|---|
1, 2 | 5V | - | - |
3, 4 | 3.3V | - | - |
5, 6, 9, 10, 19 |
DGND | - | - |
7 | DWM_SD_CMD | - | - |
8 | DWM_SD_CLK | - | - |
11 | DWM_SD_DAT0 | - | - |
12, 14, 16, 18, 20, 22 |
N.C. | - | - |
13 | DWM_SD_DAT1 | - | - |
15 | DWM_SD_DAT2 | - | - |
17 | DWM_SD_DAT3 | - | - |
21 | DWM_UART_RX | - | - |
23 | DWM_UART_CTS | - | - |
24 | DWM_BT_F5 | - | - |
25 | DWM_UART_TX | - | - |
26 | DWM_BT_F2 | - | - |
27 | DWM_UART_RTS | - | - |
28 | DWM_WIFI_IRQ | - | - |
29 | DWM_BT_EN | - | - |
30 | DWM_WIFI_EN | - | - |
PMODEdit
Digilent Pmod™ Compatible headersEdit
Please note that:
- Digilent Pmod™ Interface Specification - defined by Digilent Inc. - allows to quickly connect several pre-built I/O modules to PL:
- Signals used to implement LVDS LCD interface can alternatively routed to Digilent Pmod™ Compatible compatible connector
Digilent Pmod™ Compatible - JP17Edit
JP17 is a 12-pin 6x2x2.54 pitch vertical header. The following table reports the pinout of the connector:
Pin# | Pin name | Function | Notes |
---|---|---|---|
1 | PMOD_A0 | - | |
2 | PMOD_A4 | - | |
3 | PMOD_A1 | - | |
4 | PMOD_A5 | - | |
5 | PMOD_A2 | - | |
6 | PMOD_A6 | - | |
7 | PMOD_A3 | - | |
8 | PMOD_A7 | - | |
9, 10 | DGND | Ground | - |
11, 12 | 3.3V | - |
Digilent Pmod™ Compatible - JP23Edit
JP23 is a 12-pin 6x2x2.54 pitch vertical header. The following table reports the pinout of the connector:
Pin# | Pin name | Function | Notes |
---|---|---|---|
1 | PMOD_B0 | - | - |
2 | PMOD_B4 | - | - |
3 | PMOD_B1 | - | - |
4 | PMOD_B5 | - | - |
5 | PMOD_B2 | - | - |
6 | PMOD_B6 | - | - |
7 | PMOD_B3 | - | - |
8 | PMOD_B7 | - | - |
9, 10 | DGND | Ground | - |
11, 12 | 3.3V | - | - |
FMCEdit
FPGA Mezzanine Card (FMC) Connector - J27Edit
J27 is a 400 pins ANSI/VITA 57.1-2008 FPGA Mezzanine Card Connector that allows to connect to standard I/O mezzanine cards.
Please note that BoraXpress EVB FMC Connector is:
- fully compliant to FMC LPC
- partially compliant to FMC HPC because HPC side is not fully populated.
The following tables detail how BORA Xpress signals have been routed to FMC connector. At this link a spreadsheet providing the same information is available for download.
For more information about I/O voltage of single-ended signals available on FMC connector, please refer to this section.
HPC Row AEdit
Pin# | Pin name | Function | Notes |
---|---|---|---|
A1 | DGND | GND | |
A2 | MGTxRXP1 | DP1_M2C_P | |
A3 | MGTxRXN1 | DP1_M2C_N | |
A4 | DGND | GND | |
A5 | DGND | GND | |
A6 | MGTxRXP2 | DP2_M2C_P | |
A7 | MGTxRXN2 | DP2_M2C_N | |
A8 | DGND | GND | |
A9 | DGND | GND | |
A10 | MGTxRXP3 | DP3_M2C_P | |
A11 | MGTxRXN3 | DP3_M2C_N | |
A12 | DGND | GND | |
A13 | DGND | GND | |
A14 | not connected | DP4_M2C_P | |
A15 | not connected | DP4_M2C_N | |
A16 | DGND | GND | |
A17 | DGND | GND | |
A18 | not connected | DP5_M2C_P | |
A19 | not connected | DP5_M2C_N | |
A20 | DGND | GND | |
A21 | DGND | GND | |
A22 | MGTxTXP1 | DP1_C2M_P | |
A23 | MGTxTXN1 | DP1_C2M_N | |
A24 | DGND | GND | |
A25 | DGND | GND | |
A26 | MGTxTXP2 | DP2_C2M_P | |
A27 | MGTxTXN2 | DP2_C2M_N | |
A28 | DGND | GND | |
A29 | DGND | GND | |
A30 | MGTxTXP3 | DP3_C2M_P | |
A31 | MGTxTXN3 | DP3_C2M_N | |
A32 | DGND | GND | |
A33 | DGND | GND | |
A34 | not connected | DP4_C2M_P | |
A35 | not connected | DP4_C2M_N | |
A36 | DGND | GND | |
A37 | DGND | GND | |
A38 | not connected | DP5_C2M_P | |
A39 | not connected | DP5_C2M_N | |
A40 | DGND | GND |
HPC Row BEdit
Pin# | Pin name | Function | Notes |
---|---|---|---|
B1 | RSVD | RES1 | |
B2 | DGND | GND | |
B3 | DGND | GND | |
B4 | not connected | DP9_M2C_P | |
B5 | not connected | DP9_M2C_N | |
B6 | DGND | GND | |
B7 | DGND | GND | |
B8 | not connected | DP8_M2C_P | |
B9 | not connected | DP8_M2C_N | |
B10 | DGND | GND | |
B11 | DGND | GND | |
B12 | not connected | DP7_M2C_P | |
B13 | not connected | DP7_M2C_N | |
B14 | DGND | GND | |
B15 | DGND | GND | |
B16 | not connected | DP6_M2C_P | |
B17 | not connected | DP6_M2C_N | |
B18 | DGND | GND | |
B19 | DGND | GND | |
B20 | MGTREFCLK1P | GBTCLK1_M2C_P | |
B21 | MGTREFCLK1N | GBTCLK1_M2C_N | |
B22 | DGND | GND | |
B23 | DGND | GND | |
B24 | not connected | DP9_C2M_P | |
B25 | not connected | DP9_C2M_N | |
B26 | DGND | GND | |
B27 | DGND | GND | |
B28 | not connected | DP8_C2M_P | |
B29 | not connected | DP8_C2M_N | |
B30 | DGND | GND | |
B31 | DGND | GND | |
B32 | not connected | DP7_C2M_P | |
B33 | not connected | DP7_C2M_N | |
B34 | DGND | GND | |
B35 | DGND | GND | |
B36 | not connected | DP6_C2M_P | |
B37 | not connected | DP6_C2M_N | |
B38 | DGND | GND | |
B39 | DGND | GND | |
B40 | RSVD | RES0 |
LPC Row CEdit
Pin# | Pin name | Function | Notes |
---|---|---|---|
C1 | DGND | GND | |
C2 | MGTxTXP0 | DP0_C2M_P | |
C3 | MGTxTXN0 | DP0_C2M_N | |
C4 | DGND | GND | |
C5 | DGND | GND | |
C6 | MGTxRXP0 | DP0_M2C_P | |
C7 | MGTxRXN0 | DP0_M2C_N | |
C8 | DGND | GND | |
C9 | DGND | GND | |
C10 | IO_L23P_T3_34 | LA06_P | |
C11 | IO_L23N_T3_34 | LA06_N | |
C12 | DGND | GND | |
C13 | DGND | GND | |
C14 | IO_L2P_T0_34 | LA10_P | |
C15 | IO_L2N_T0_34 | LA10_N | |
C16 | DGND | GND | |
C17 | DGND | GND | |
C18 | IO_L1P_T0_34 | LA14_P | |
C19 | IO_L1N_T0_34 | LA14_N | |
C20 | DGND | GND | |
C21 | DGND | GND | |
C22 | IO_L16P_T2_34 | LA18_P_CC | |
C23 | IO_L16N_T2_34 | LA18_N_CC | |
C24 | DGND | GND | |
C25 | DGND | GND | |
C26 | IO_L6P_T0_35 | LA27_P | |
C27 | IO_L6N_T0_VREF_35 | LA27_N | |
C28 | DGND | GND | |
C29 | DGND | GND | |
C30 | I2C0_SCL | SCL | |
C31 | I2C0_SDA | SDA | |
C32 | DGND | GND | |
C33 | DGND | GND | |
C34 | GA0 | GA0 | |
C35 | FMC_12P0V | 12P0V | |
C36 | DGND | GND | |
C37 | FMC_12P0V | 12P0V | |
C38 | DGND | GND | |
C39 | FMC_3P3V | 3P3V | |
C40 | DGND | GND |
LPC Row DEdit
Pin# | Pin name | Function | Notes |
---|---|---|---|
D1 | IO_25_VRP_34 | PG_C2M | |
D2 | DGND | GND | |
D3 | DGND | GND | |
D4 | MGTREFCLK0P | GBTCLK0_M2C_P | |
D5 | MGTREFCLK0N | GBTCLK0_M2C_N | |
D6 | DGND | GND | |
D7 | DGND | GND | |
D8 | IO_L14P_T2_SRCC_34 | LA01_P_CC | |
D9 | IO_L14N_T2_SRCC_34 | LA01_N_CC | |
D10 | DGND | GND | |
D11 | IO_L9P_T1_DQS_34 | LA05_P | |
D12 | IO_L9N_T1_DQS_34 | LA05_N | |
D13 | DGND | GND | |
D14 | IO_L6P_T0_34 | LA09_P | |
D15 | IO_L6N_T0_VREF_34 | LA09_N | |
D16 | DGND | GND | |
D17 | IO_L20P_T3_34 | LA13_P | |
D18 | IO_L20N_T3_34 | LA13_N | |
D19 | DGND | GND | |
D20 | IO_L15P_T2_DQS_34 | LA17_P_CC | |
D21 | IO_L15N_T2_DQS_34 | LA17_N_CC | |
D22 | DGND | GND | |
D23 | IO_L2P_T0_AD8P_35 | LA23_P | |
D24 | IO_L2N_T0_AD8N_35 | LA23_N | |
D25 | DGND | GND | |
D26 | IO_L5P_T0_AD9P_35 | LA26_P | |
D27 | IO_L5N_T0_AD9N_35 | LA26_N | |
D28 | DGND | GND | |
D29 | JTAG_TCK | TCK | |
D30 | JTAG_TDI | TDI | |
D31 | FMC_TDO_ZYNQ_TDI | TDO | |
D32 | FMC_3P3VAUX | 3P3VAUX | |
D33 | JTAG_TMS | TMS | |
D34 | JTAG_TRSTn | TRST_L | |
D35 | GA0 | GA1 | |
D36 | FMC_3P3V | 3P3V | |
D37 | DGND | GND | |
D38 | FMC_3P3V | 3P3V | |
D39 | DGND | GND | |
D40 | FMC_3P3V | 3P3V |
HPC Row EEdit
Pin# | Pin name | Function | Notes |
---|---|---|---|
E1 | DGND | GND | |
E2 | IO_L14P_T2_AD4P_SRCC_35 | HA01_P_CC | |
E3 | IO_L14N_T2_AD4N_SRCC_35 | HA01_N_CC | |
E4 | DGND | GND | |
E5 | DGND | GND | |
E6 | IO_L20P_T3_AD6P_35 | HA05_P | |
E7 | IO_L20N_T3_AD6N_35 | HA05_N | |
E8 | DGND | GND | |
E9 | IO_L24P_T3_AD15P_35 | HA09_P | |
E10 | IO_L24N_T3_AD15N_35 | HA09_N | |
E11 | DGND | GND | |
E12 | not connected | HA13_P | |
E13 | not connected | HA13_N | |
E14 | DGND | GND | |
E15 | not connected | HA16_P | |
E16 | not connected | HA16_N | |
E17 | DGND | GND | |
E18 | not connected | HA20_P | |
E19 | not connected | HA20_N | |
E20 | DGND | GND | |
E21 | not connected | HB03_P | |
E22 | not connected | HB03_N | |
E23 | DGND | GND | |
E24 | not connected | HB05_P | |
E25 | not connected | HB05_N | |
E26 | DGND | GND | |
E27 | not connected | HB09_P | |
E28 | not connected | HB09_N | |
E29 | DGND | GND | |
E30 | not connected | HB13_P | |
E31 | not connected | HB13_N | |
E32 | DGND | GND | |
E33 | not connected | HB19_P | |
E34 | not connected | HB19_N | |
E35 | DGND | GND | |
E36 | not connected | HB21_P | |
E37 | not connected | HB21_N | |
E38 | DGND | GND | |
E39 | FMC_VADJ | VADJ | |
E40 | DGND | GND |
HPC Row FEdit
Pin# | Pin name | Function | Notes |
---|---|---|---|
F1 | IO_0_VRN_35 | PG_M2C | |
F2 | DGND | GND | |
F3 | DGND | GND | |
F4 | IO_L13P_T2_MRCC_35 | HA00_P_CC | |
F5 | IO_L13N_T2_MRCC_35 | HA00_N_CC | |
F6 | DGND | GND | |
F7 | IO_L19P_T3_35 | HA04_P | |
F8 | IO_L19N_T3_VREF_35 | HA04_N | |
F9 | DGND | GND | |
F10 | IO_L23P_T3_35 | HA08_P | |
F11 | IO_L23N_T3_35 | HA08_N | |
F12 | DGND | GND | |
F13 | not connected | HA12_P | |
F14 | not connected | HA12_N | |
F15 | DGND | GND | |
F16 | not connected | HA15_P | |
F17 | not connected | HA15_N | |
F18 | DGND | GND | |
F19 | not connected | HA19_P | |
F20 | not connected | HA19_N | |
F21 | DGND | GND | |
F22 | not connected | HB02_P | |
F23 | not connected | HB02_N | |
F24 | DGND | GND | |
F25 | not connected | HB04_P | |
F26 | not connected | HB04_N | |
F27 | DGND | GND | |
F28 | not connected | HB08_P | |
F29 | not connected | HB08_N | |
F30 | DGND | GND | |
F31 | not connected | HB12_P | |
F32 | not connected | HB12_N | |
F33 | DGND | GND | |
F34 | not connected | HB16_P | |
F35 | not connected | HB16_N | |
F36 | DGND | GND | |
F37 | not connected | HB20_P | |
F38 | not connected | HB20_N | |
F39 | DGND | GND | |
F40 | FMC_VADJ | VADJ |
LPC Row GEdit
Pin# | Pin name | Function | Notes |
---|---|---|---|
G1 | DGND | GND | |
G2 | IO_L11P_T1_SRCC_34 | CLK0_C2M_P | |
G3 | IO_L11N_T1_SRCC_34 | CLK0_C2M_N | |
G4 | DGND | GND | |
G5 | DGND | GND | |
G6 | IO_L13P_T1_MRCC_34 | LA00_P_CC | |
G7 | IO_L13N_T1_MRCC_34 | LA00_N_CC | |
G8 | DGND | GND | |
G9 | IO_L4P_T0_34 | LA03_P | |
G10 | IO_L4N_T0_34 | LA03_N | |
G11 | DGND | GND | |
G12 | IO_L3P_T0_DQS_PUDC_B_34 | LA08_P | |
G13 | IO_L3N_T0_DQS_34 | LA08_N | |
G14 | DGND | GND | |
G15 | IO_L22P_T3_34 | LA12_P | |
G16 | IO_L22N_T3_34 | LA12_N | |
G17 | DGND | GND | |
G18 | IO_L19P_T3_34 | LA16_P | |
G19 | IO_L19N_T3_VREF_34 | LA16_N | |
G20 | DGND | GND | |
G21 | IO_L17P_T2_34 | LA20_P | |
G22 | IO_L17N_T2_34 | LA20_N | |
G23 | DGND | GND | |
G24 | IO_L1P_T0_AD0P_35 | LA22_P | |
G25 | IO_L1N_T0_AD0N_35 | LA22_N | |
G26 | DGND | GND | |
G27 | IO_L4P_T0_35 | LA25_P | |
G28 | IO_L4N_T0_35 | LA25_N | |
G29 | DGND | GND | |
G30 | IO_L8P_T1_AD10P_35 | LA29_P | |
G31 | IO_L8N_T1_AD10N_35 | LA29_N | |
G32 | DGND | GND | |
G33 | IO_L10P_T1_AD11P_35 | LA31_P | |
G34 | IO_L10N_T1_AD11N_35 | LA31_N | |
G35 | DGND | GND | |
G36 | IO_L16P_T2_35 | LA33_P | |
G37 | IO_L16N_T2_35 | LA33_N | |
G38 | DGND | GND | |
G39 | FMC_VADJ | VADJ | |
G40 | DGND | GND |
LPC Row HEdit
Pin# | Pin name | Function | Notes |
---|---|---|---|
H1 | FMC_VREF_A_M2C | VREF_A_M2C | |
H2 | FMC_PRSNT_M2C_L | PRSNT_M2C_L | |
H3 | DGND | GND | |
H4 | IO_L12P_T1_MRCC_34 | CLK0_M2C_P | |
H5 | IO_L12N_T1_MRCC_34 | CLK0_M2C_N | |
H6 | DGND | GND | |
H7 | IO_L7P_T1_34 | LA02_P | |
H8 | IO_L7N_T1_34 | LA02_N | |
H9 | DGND | GND | |
H10 | IO_L5P_T0_34 | LA04_P | |
H11 | IO_L5N_T0_34 | LA04_N | |
H12 | DGND | GND | |
H13 | IO_L8P_T1_34 | LA07_P | |
H14 | IO_L8N_T1_34 | LA07_N | |
H15 | DGND | GND | |
H16 | IO_L21P_T3_DQS_34 | LA11_P | |
H17 | IO_L21N_T3_DQS_34 | LA11_N | |
H18 | DGND | GND | |
H19 | IO_L18P_T2_34 | LA15_P | |
H20 | IO_L18N_T2_34 | LA15_N | |
H21 | DGND | GND | |
H22 | IO_L24P_T3_34 | LA19_P | |
H23 | IO_L24N_T3_34 | LA19_N | |
H24 | DGND | GND | |
H25 | IO_L10P_T1_34 | LA21_P | |
H26 | IO_L10N_T1_34 | LA21_N | |
H27 | DGND | GND | |
H28 | IO_L3P_T0_DQS_AD1P_35 | LA24_P | |
H29 | IO_L3N_T0_DQS_AD1N_35 | LA24_N | |
H30 | DGND | GND | |
H31 | IO_L7P_T1_AD2P_35 | LA28_P | |
H32 | IO_L7N_T1_AD2N_35 | LA28_N | |
H33 | DGND | GND | |
H34 | IO_L9P_T1_DQS_AD3P_35 | LA30_P | |
H35 | IO_L9N_T1_DQS_AD3N_35 | LA30_N | |
H36 | DGND | GND | |
H37 | IO_L15P_T2_DQS_AD12P_35 | LA32_P | |
H38 | IO_L15N_T2_DQS_AD12N_35 | LA32_N | |
H39 | DGND | GND | |
H40 | FMC_VADJ | VADJ |
HPC Row JEdit
Pin# | Pin name | Function | Notes |
---|---|---|---|
J1 | DGND | GND | |
J2 | IO_L11P_T1_SRCC_35 | CLK1_C2M_P | |
J3 | IO_L11N_T1_SRCC_35 | CLK1_C2M_N | |
J4 | DGND | GND | |
J5 | DGND | GND | |
J6 | IO_L18P_T2_AD13P_35 | HA03_P | |
J7 | IO_L18N_T2_AD13N_35 | HA03_N | |
J8 | DGND | GND | |
J9 | IO_L22P_T3_AD7P_35 | HA07_P | |
J10 | IO_L22N_T3_AD7N_35 | HA07_N | |
J11 | DGND | GND | |
J12 | not connected | HA11_P | |
J13 | not connected | HA11_N | |
J14 | DGND | GND | |
J15 | not connected | HA14_P | |
J16 | not connected | HA14_N | |
J17 | DGND | GND | |
J18 | not connected | HA18_P | |
J19 | not connected | HA18_N | |
J20 | DGND | GND | |
J21 | not connected | HA22_P | |
J22 | not connected | HA22_N | |
J23 | DGND | GND | |
J24 | not connected | HB01_P | |
J25 | not connected | HB01_N | |
J26 | DGND | GND | |
J27 | not connected | HB07_P | |
J28 | not connected | HB07_N | |
J29 | DGND | GND | |
J30 | not connected | HB11_P | |
J31 | not connected | HB11_N | |
J32 | DGND | GND | |
J33 | not connected | HB15_P | |
J34 | not connected | HB15_N | |
J35 | DGND | GND | |
J36 | not connected | HB18_P | |
J37 | not connected | HB18_N | |
J38 | DGND | GND | |
J39 | not connected | VIO_B_M2C | |
J40 | DGND | GND |
HPC Row KEdit
Pin# | Pin name | Function | Notes |
---|---|---|---|
K1 | not connected | VREF_B_M2C | |
K2 | DGND | GND | |
K3 | DGND | GND | |
K4 | IO_L12P_T1_MRCC_35 | CLK1_M2C_P | |
K5 | IO_L12N_T1_MRCC_35 | CLK1_M2C_N | |
K6 | DGND | GND | |
K7 | IO_L17P_T2_AD5P_35 | HA02_P | |
K8 | IO_L17N_T2_AD5N_35 | HA02_N | |
K9 | DGND | GND | |
K10 | IO_L21P_T3_DQS_AD14P_35 | HA06_P | |
K11 | IO_L21N_T3_DQS_AD14N_35 | HA06_N | |
K12 | DGND | GND | |
K13 | IO_25_VRP_35 | HA10_P | |
K14 | not connected | HA10_N | |
K15 | DGND | GND | |
K16 | not connected | HA17_P_CC | |
K17 | not connected | HA17_N_CC | |
K18 | DGND | GND | |
K19 | not connected | HA21_P | |
K20 | not connected | HA21_N | |
K21 | DGND | GND | |
K22 | not connected | HA23_P | |
K23 | not connected | HA23_N | |
K24 | DGND | GND | |
K25 | not connected | HB00_P_CC | |
K26 | not connected | HB00_N_CC | |
K27 | DGND | GND | |
K28 | not connected | HB06_P_CC | |
K29 | not connected | HB06_N_CC | |
K30 | DGND | GND | |
K31 | not connected | HB10_P | |
K32 | not connected | HB10_N | |
K33 | DGND | GND | |
K34 | not connected | HB14_P | |
K35 | not connected | HB14_N | |
K36 | DGND | GND | |
K37 | not connected | HB17_P_CC | |
K38 | not connected | HB17_N_CC | |
K39 | DGND | GND | |
K40 | not connected | VIO_B_M2C |
Electrical and Mechanical DocumentsEdit
SchematicsEdit
BOMEdit
- BoraXEVB: BORAXEVB_S.EVBBX0000C0R.1.6.0.CSV.zip
LayoutEdit
PCB design (Mentor PADS)Edit
MechanicalEdit
- DXF: boraxevb-2D-CS143714
- IDF (3D): boraxevb-3D-CS143714
- STEP (3D): boraxevb_3D_step_cs143714