Changes

Jump to: navigation, search

AxelEVB-Lite

985 bytes removed, 10:55, 3 December 2019
→‎Axel Lite
{{ImportantMessage|text=This page provides information for the AxelEVB-Lite carrier board model S-EVBA1000C1R (BOM 1.0.4), provided with XELK kits version 2.1.0 and above.
 
For AxelEVB-Lite revision 0 manufactured before the release of XELK 2.1.0, please refer to [[AxelEVB-Lite_rev.0|this page]].
}}
 
 
{{InfoBoxTop}}
{{AppliesToAxel}}
{{AppliesToAxelLite}}
{{AppliesToAxelEsatta}}
{{InfoBoxBottom}}
[[File:Axelevb-lite-01.png|500px|frameless|border]]==Introduction==
==Introduction==AxelEVB-Lite is a carrier board designed to host [[File:Axel Ultra SOM-evb-lite-revA 02.jpg|Axel Ultra]] and [[Axel Lite SOM500px|Axel Lite]] (through an adapter) SoMs. It exports some specific peripherals connectors and acts as an adaptation board used in combination with [[:Category:Dacuframeless|Dacuborder]] carrier board.
{{ImportantMessage|text=This page provides information for the AxelEVB-Lite is a carrier board model S-EVBA1000C1R designed to host [[:Category:AxelUltra|AXEL ULTRA]] and [[:Category:AxelLite|AXEL LITE]] (BOM 1.0.4through an adapter), provided with XELK kits version 2SoMs.1.0 It exports some specific peripherals connectors and above. If you have a acts as an adaptation board from a previous version of the XELK kit (older than 2.1.0), please contact used in combination with [[mailto:support-axel@dave.eu support-axel@dave.euCategory:Dacu|Dacu]]carrier board.}}
==Block Diagram==
The following picture shows Axel-EVB-Lite's block diagram:
[[File:Axelevb-lite-block diagram.png|700px|frameless|border|centre]]
== Features ==
* 1x USB OTG,1x USB HOST
* Serial port (RS232)
* JTAG
* HDMI connector
* SATA connector
=== MIPI camera connector - J53 ===
J16 J53 is a 33-pin 0.50mm pitch ZIF connector
The following table reports the connector's pinout:
!Notes
|-
|1 || SPI_MOSI_IPU2_CS1<br>[CSI_D15] CSI_CLK0P || CAM DATA[15] - || -
|-
|2 || CSI_D14CSI_CLK0M || CAM DATA[14] - || -
|-
|3 4 || SPI1_CS_IPU2_CSI1CSI_D0P || - || -
|-
|4 5 || CMOS_RST#_IPU2_CSI1CSI_D0M || CMOS Reset - || -
|-
|5 7 || SPI1_CLK_IPU2_CS1CSI_D1P || - || -
|-
|6 8 || SPI1_MISO_IPU2_CS1CSI_D1M || - || -
|-
|7 10 || CMOS_I2C_SDACSI_D2P || I2C DATA - || -
|-
|8 11 || CMOS_I2C_SCLCSI_D2M || I2C CLOCK - || -
|-
|9 13 || EIM_DA9CSI_D3P || CAM DATA[0] - || -
|-
|10 14 || EIM_DA8CSI_D3M || CAM DATA[1] - || -
|-
|11 16 || DGNDDSI_D1P || Ground - || -
|-
|12 17 || DGNDDSI_D1M || Ground - || -
|-
|13 19 || EIM_DA7DSI_D0P || CAM DATA[2] - || -
|-
|14 20 || EIM_DA6DSI_D0M || CAM DATA[3] - || -
|-
|15 22 || EIM_DA5DSI_CLK0P || CAM DATA[4] - || -
|-
|16 23 || EIM_DA4DSI_DCK0M || CAM DATA[5] - || -
|-
|17 3, 6, 9, 12<br>15, 18, 21, 24 || EIM_DA3DGND || CAM DATA[6] - || -
|-
|18 25 || EIM_DA2KEY_COL3/I2C2_SCL || CAM DATA[7] - || -
|-
|19 26 || EIM_DA1KEY_ROW3/I2C2_SDA || CAM DATA[8] - || -
|-
|20 27, 28 || EIM_DA03.3V || CAM DATA[9] - || -
|-
|21 29 || CSI1_D10GPIO_19 || CAM DATA[10] - || -
|-
|22 30 || CSI1_D11GPIO_18 || CAM DATA[11] - || -
|-
|23 31 || CSI1_D12GPIO_16 || CAM DATA[12] - || -
|-
|24 32, 33 || CSI1_D135V || CAM DATA[13] - || -
|-
|25 || CSI1_CAM_HS} === USB OTG - J29 === J29 is a standard USB Micro AB connector.  The following table reports the connector's pinout: {|| CAM Hsync || -class="wikitable"
|-
|26 || CSI1_CAM_VS|| CAM Vsync || -!Pin# !Pin name!Function!Notes
|-
|27 || DGND|| Ground || -|-|28 || CSI1_CAM_PCLK|| CAM Pixel Clock || -|-|29 || DGND|| Ground || -|-|30 || R_CMOS_CLK_IPU2_CSI1|| CMOS Clock || -|-|31 || DGND|| Ground || -|-|32 || N.C.|| - || -|-|33 || N.C.|| - || -|-|34 || CAM_VCC_IPU2_CSI1|| Power Supply || -|-|35 || CAM_VCC_IPU2_CSI1|| Power Supply || -|-|36 || CAM_VCC_IPU2_CSI1|| Power Supply || -|-|37, 38, 39, 40 || SH_CAM || Shield to Ground || -|-|} === USB OTG - J29 === J29 is a standard USB Micro AB connector.  The following table reports the connector's pinout: {| class="wikitable" |-!Pin# !Pin name!Function!Notes|-|1 ||DGND || Ground || -
|-
|2 ||OTG_ID || USB OTG ID || -
|}
=== LVDS0 - J50 J54 ===
J50 J54 is a 10x2 DF13A-20DP header. The following table reports the connector's pinout:
{| class="wikitable"
=== Pin strip connectors ===
==== J-PROG-MICRO1 PMIC1 ====
J-PROG-MICRO1 PMIC1 is a 3x24x2-pin, 2.54mm pitch header, pinstrip connector. The following table reports the connector's pinout:
{| class="wikitable"
!Notes
|-
|1 || BKGD_JM60PMIC_PROG_VPGM|| - || -
|-
|2 || DGND2V8-4V5|| Ground - || -
|-
|3, 5 || N.C. DGND|| - Ground || -
|-
|4 || RST_JM60PMIC_PROG_SCL|| - || -
|-
|6 5 || VIN_USBPMIC_PROG_SDA|| - || -
|-
|} ==== J-PROG-PMIC1 ==== J-PROG-PMIC1 is a 4x2-pin, 2.54mm pitch header, pinstrip connector. The following table reports the connector's pinout: {| class="wikitable" |-!Pin# !Pin name!Function!Notes|-|1 || PMIC_PROG_VPGM|| - || -|-|2 || 2V8-4V5|| - || -|-|3 || DGND|| Ground || -|-|4 || PMIC_PROG_SCL|| - || -|-|5 || PMIC_PROG_SDA|| - || -|-|6 || PMIC_PWRON || - || -
|-
|7 || MCU_GPIO1|| - || -
|1 || 2V8-4V5|| - || -
|-
|2 || MIC_PROG_GATE_CTRlPMIC_PROG_GATE_CTRl|| - || -
|-
|3 || DGND|| Ground || -
!Notes
|-
|1 || - || - || Connetted Connected to pin 3
|-
|2 || DGND|| Ground|| -
|-
|3 || - || - || Connetted Connected to pin 1
|-
|4, 6, 8, 10,<br>12, 14, 16 || NVCC_CSI_EXT|| - || -
!Notes
|-
|1 || - || - || Connetted Connected to pin 3
|-
|2 || DGND|| Ground|| -
|-
|3 || - || - || Connetted Connected to pin 1
|-
|4, 6, 8, 10,<br>12, 14, 16 || NVCC_EIM_EXT|| - || -
|}
==== MIPI CSI - JP7 ====
 
JP7 is a 8x2-pin 2.54mm pitch header pinstrip connector. The following table reports the connector's pinout:
 
{| class="wikitable"
|-
!Pin#
!Pin name
!Function
!Notes
|-
|1 || CSI_D3P || Data3 + ||
|-
|2, 5, 8, 11,<br> 14, 16 || DGND|| Ground|| -
|-
|3 || CSI_D3N || Data3- ||
|-
|4 || CSI_D2P|| Data2+ || -
|-
|6 || CSI_D2M|| Data2-|| -
|-
|7 || CSI_D1P|| Data1+|| -
|-
|9 || CSI_D1M|| Data1- || -
|-
|13 || CSI_CLK0P|| Clock+ || -
|-
|15 || CSI_CLK0M|| Clock- || -
|-
|}
==== EXPANSION CONNECTOR - JP8 ====
|}
==Boot configurations == MIPI DSI The AxelEVB- JP11 Lite carrier board can host two different SoM's, [[:Category:AxelUltra|Axel Ultra]] and [[:Category:AxelLite|Axel Lite]]. The following sections detail boot configuration options, which differ depending on the SoM. ===Axel Ultra======= uSD card ==== Dip-switch configuration: <pre>S5[1..8] : On Off On On On On Off OffS6[1..8] : Off Off On On Off On On OnS7[1..8] : Off Off On On On On On On S8[1..8] : On Off On On Off On On OnS9[1..2] : Off Off</pre> ==== SPI NOR flash ====
JP11 is a 8x2Dip-pin 2.54mm pitch header pinstrip connector. The following table reports the connector's pinoutswitch configuration:
{| class="wikitable" <pre>|-S5[1..8] : On On Off Off On On Off Off !Pin# S6[1..8] : Off Off On On Off On On On!Pin nameS7[1..8] : Off Off On Off Off Off On Off!Function!Notes|-S8[1..8] : On Off On On Off On On On|S9[1, ..2, 7, 8,] : Off Off<br/pre> 12, 13, 15, 16 || DGND || Ground || |-===Axel Lite===|3 || DSI_D1M || Data1 - || |-|4 || DSI_CLOCK0M || Clock - |||-|5 || DSI_D1P || Data1 + |||-|6 || DSI_CLOCK0P || Clock + |||In this case, it is required to use the [[AxelEVB-|9 || DSI_DOP|| Data0 + |||Lite-|10 Adapter (AxelLite)|| NVCC_AXEL_I/O_3specific revision A adapter]] to plug the SoM.3V/1.8|| Regarding the boot options, please refer to [[AxelEVB- |||Lite-|11 || DSI_D0M|| Data0 - ||Adapter_(AxelLite)#Revision_A_2|-|14 || SW4_xV/1this section]].8V || - |||-|}
==SchematicsTechnical documents ==
===Schematics===* ORCAD: http://wwwmirror.dave.eu/systemaxel/hw/filesAxelEVB/arearev-riservataA/axelevb-litelite_S-EVBA1000C1R_1.0.98.3-XELK-dsndsn_.zip* PDF: http://wwwmirror.dave.eu/systemaxel/hw/filesAxelEVB/arearev-riservataA/axelevb-litelite_S-SEVBA1000C1R_1.EVBA1000C0R-0.9.38.pdf
===BOM===* AxelEVB-Lite: http://wwwmirror.dave.eu/systemaxel/hw/filesAxelEVB/arearev-riservataA/axelevbAXELEVB-lite_BOM_SLITE_S.EVBA1000C0R_0EVBA1000C1R.91.30.CSV_8.zip
===Layout===* http://wwwmirror.dave.eu/systemaxel/hw/filesAxelEVB/arearev-riservataA/axelevb-lite_CS151613_assem_viewlite_S-EVBA1000C1R_CS151613A_AssemView.pdf
===Mechanical===* DXF: http://wwwmirror.dave.eu/systemaxel/hw/filesAxelEVB/arearev-riservataA/axelevb-lite_2D_CS151613lite-S-EVBA1000C1R_CS151613A-2D.dxf_.zip* IDF (3D): http://wwwmirror.dave.eu/systemhw/filesaxel/areaAxelEVB/rev-riservataA/axelevb-lite_3D_CS151613lite-S-EVBA1000C1R_CS151613A-3D.idf_.zip
U0001
Bureaucrats, dave_user, Administrators
4,650
edits
Retrieved from "https://wiki.dave.eu/index.php/Special:MobileDiff/3413...9222"

Navigation menu