{{ImportantMessage|text=This page provides information for the AxelEVB-Lite carrier board model S-EVBA1000C1R (BOM 1.0.4), provided with XELK kits version 2.1.0 and above.
For AxelEVB-Lite revision 0 manufactured before the release of XELK 2.1.0, please refer to [[AxelEVB-Lite_rev.0|this page]].
==Introduction==AxelEVB-Lite is a carrier board designed to host [[File:Axel Ultra SOM-evb-lite-revA 02.jpg|Axel Ultra]] and [[Axel Lite SOM500px|Axel Lite]] (through an adapter) SoMs. It exports some specific peripherals connectors and acts as an adaptation board used in combination with [[:Category:Dacuframeless|Dacuborder]] carrier board.
{{ImportantMessage|text=This page provides information for the AxelEVB-Lite is a carrier board model S-EVBA1000C1R designed to host [[:Category:AxelUltra|AXEL ULTRA]] and [[:Category:AxelLite|AXEL LITE]] (BOM 1.0.4through an adapter), provided with XELK kits version 2SoMs.1.0 It exports some specific peripherals connectors and above. If you have a acts as an adaptation board from a previous version of the XELK kit (older than 2.1.0), please contact used in combination with [[mailto:support-axel@dave.eu support-axel@dave.euCategory:Dacu|Dacu]]carrier board.}}
==Block Diagram==
The following picture shows Axel-EVB-Lite's block diagram:
==== J-PROG-MICRO1 ====J-PROG-MICRO1 JP17 is a 3x212-pin, 26x2x2.54mm 54 pitch vertical header, pinstrip connector. The following table reports the pinout of the connector's pinout:
JP7 is a 8x2-pin 2.54mm pitch header pinstrip connector. The following table reports the connector's pinout:
{| class="wikitable"
|-
!Pin#
!Pin name
!Function
!Notes
|-
|1 || CSI_D3P || Data3 + ||
|-
|2, 5, 8, 11,<br> 14, 16 || DGND|| Ground|| -
|-
|3 || CSI_D3N || Data3- ||
|-
|4 || CSI_D2P|| Data2+ || -
|-
|6 || CSI_D2M|| Data2-|| -
|-
|7 || CSI_D1P|| Data1+|| -
|-
|9 || CSI_D1M|| Data1- || -
|-
|13 || CSI_CLK0P|| Clock+ || -
|-
|15 || CSI_CLK0M|| Clock- || -
|-
|}
==== EXPANSION CONNECTOR - JP8 ====
|}
==Boot configurations == MIPI DSI The AxelEVB- JP11 ====Lite carrier board can host two different SoM's, [[:Category:AxelUltra|Axel Ultra]] and [[:Category:AxelLite|Axel Lite]].
JP11 is a 8x2-pin 2.54mm pitch header pinstrip connector. The following table reports sections detail boot configuration options, which differ depending on the connector's pinout:SoM.
{| class="wikitable" ==Axel Ultra======= uSD card ==== |Dip-switch configuration:!Pin# !Pin name<pre>S5[1..8] : On Off On On On On Off Off!FunctionS6[1..8] : Off Off On On Off On On On!NotesS7[1..8] : Off Off On On On On On On |-S8[1..8] : On Off On On Off On On On|S9[1, ..2, 7, 8,] : Off Off<br/pre> 12, 13, 15, 16 || DGND || Ground || |-|3 || DSI_D1M || Data1 - || ==== SPI NOR flash ====|-|4 || DSI_CLOCK0M || Clock Dip- ||switch configuration:|-|5 || DSI_D1P || Data1 + ||<pre>|-S5[1..8] : On On Off Off On On Off Off |6 || DSI_CLOCK0P S6[1..8] : Off Off On On Off On On || Clock + ||On|-S7[1..8] : Off Off On Off Off Off On Off|9 || DSI_DOP|| Data0 + ||S8[1..8] : On Off On On Off On On On|-S9[1..2] : Off Off|10 || NVCC_AXEL_I</O_3.3V/1.8|| - ||pre>|-===Axel Lite===|11 || DSI_D0M|| Data0 In this case, it is required to use the [[AxelEVB- |||Lite-|14 |Adapter (AxelLite)| SW4_xV/1specific revision A adapter]] to plug the SoM.8V || Regarding the boot options, please refer to [[AxelEVB- |||Lite-Adapter_(AxelLite)#Revision_A_2|}this section]].