Changes

Jump to: navigation, search

AxelEVB-Lite

26 bytes removed, 10:55, 3 December 2019
→‎Axel Lite
{{ImportantMessage|text=This page provides information for the AxelEVB-Lite carrier board model S-EVBA1000C1R (BOM 1.0.4), provided with XELK kits version 2.1.0 and above.
 
For AxelEVB-Lite revision 0 manufactured before the release of XELK 2.1.0, please refer to [[AxelEVB-Lite_rev.0|this page]].
}}
 
 
{{InfoBoxTop}}
{{AppliesToAxel}}
{{AppliesToAxelLite}}
{{AppliesToAxelEsatta}}
{{InfoBoxBottom}}
==Introduction== [[File:AxelevbAxel-evb-lite-01revA 02.pngjpg|500px|frameless|border]]
==Introduction==AxelEVB-Lite is a carrier board designed to host [[Axel Ultra SOM:Category:AxelUltra|Axel UltraAXEL ULTRA]] and [[Axel Lite SOM:Category:AxelLite|Axel LiteAXEL LITE]] (through an adapter) SoMs. It exports some specific peripherals connectors and acts as an adaptation board used in combination with [[:Category:Dacu|Dacu]] carrier board.
==Block Diagram==
The following picture shows Axel-EVB-Lite's block diagram:
[[File:Axelevb-lite-block diagram.png|700px|frameless|border|centre]]
== Features ==
* 1x USB OTG,1x USB HOST
* Serial port (RS232)
* JTAG
* HDMI connector
* SATA connector
!Description
|-
| <strike>ETH0 interface</strike>| <strike>Mistake in the connection of the center tap pins. They should be separated from one another and connected through separate 0.1μF common-mode capacitors to ground (for further details (eg: connection and selection of the magnetics), please refer to the Micrel KSZ9031RNX datasheet).</strike>
|-
|}
|----
|J1.98
|GPIO_18/PMIC_INT_B
|General Purpose I/O
| -
|----
|J1.122
|NVCC_AXEL_I/O_3.3V/1.8V(BOARD_PGOOD)
|3.3/1.8V
| -
|----
|J2.104
|RTC_VBATNOR_WP|RTC Battery Power SupplyNOR Write Protect|Battery on DACU board-
|----
|J2.106
|----
|J4.17
|ENET_CRS_DV//SW2_1N.8V/3C.3V
| -
| -
|----
|J4.25
|SD4_DATA1SD3_DATA6
| -
| -
|----
|J4.27
|SD4_DATA2SD3_DATA7
| -
| -
|----
|J4.29
|DISP0_DAT18DISP0_DAT22|Digital video: data-bit[1822]| -[Mount option]
|----
|J4.31
|DISP0_DAT23
|Digital video: data-bit[23]
|[Mount option]
|----
|J4.33
|DISP0_DAT19
|Digital video: data-bit[19]
| -|----|J4.33|DISP0_DAT20|Digital video: data-bit[20Mount option]| -
|----
|J4.35
|----
|J4.107
|KEY_COL4/VDDHIGH_VPHN.C.|-|-
|----
|J4.109
|----
|J4.119
|SD1_DAT0NC
| -
| -
|----
|J4.121
|SD1_DAT1NC
| -
| -
|----
|J4.123
|SD1_DAT2NC
| -
| -
|----
|J4.125
|SD1_DAT3NC
| -
| -
|----
|J4.127
|SD3_DATA4NC
|
|
|----
|J4.135
|SD1_CMDNC
| -
| -
|----
|J4.137
|SD1_CLKNc
| -
| -
|----
|J4.16
|USB_OTG_VBUSN.C.|USB power supply (+5V)-
| -
|----
|J4.18
|DISP0_DAT21DISP0_DAT18
|Digital video: data-bit[21]
| -[Mount option]
|----
|J4.20
|----
|J4.24
|DISP0_DAT22DISP0_DAT21|Digital video: data-bit[2221]| -[Mount option]
|----
|J4.26
|DISP0_DAT23DISP0_DAT20|Digital video: data-bit[2320]| -[Mount option]
|----
|J4.28
|----
|J4.32
|KEY_ROW4/VDDSOC_CAPN.C.|USB OTG control signal-
| -
|----
|----
|J4.70
|LCD0_BKLT_PWMSD4_DATA2|LCD0 backlight control signal-
| -
|----
|----
|J5.63
|N.C.AUD4_TXFS
| -
| -
|----
|J5.75
|CSI0_DAT17DI0_PIN4
| -
| -
|----
|J5.77
|CSI0_DAT18SD4_DATA0
| -
| -
|----
|J5.79
|CSI0_DAT19EIM_D23
| -
| -
|----
|J5.81
|N.C.DISP0_DAT18
| -
| -
|----
|J5.83
|N.C.DISP0_DAT19
| -
| -
|----
|J5.68
|N.C.AUD4_TXC
| -
| -
|----
|J5.70
|N.C.AUD4_RXD
| -
| -
|----
|J5.74
|N.C.AUD4_TXD
| -
| -
!Notes
|-
|1 11 || ETH0_TXRX0_P || - || -
|-
|2 10 || ETH0_TXRX0_M || - || -
|-
|3 4 || ETH0_TXRX1_P || - || -
|-
|4 3 || ETH0_TXRX2_P || - || -
|-
|5 2 || ETH0_TXRX2_M || - || -
|-
|6 5 || ETH0_TXRX1_M || - || -
|-
|7 8 || ETH0_TXRX3_P || - || -
|-
|8 9 || ETH0_TXRX3_M || - || -
|-
|9 15 || NVCC_AXEL_I/O_3.3V/1.8V ETH0_LED1 || - || -
|-
|10 13 || ETH_SH ETH0_LED2 || - || -
|-
|1117, 13 || NVCC_AXEL_I/O_3.3V/1.8V || - || -|-|12 || ETH0_LED1 || - || -|-|14 || ETH0_LED2 || - || -|-|15, 16 18 || ETH_SH || - || -
|-
|}
|}Please refer to the carrier board schematics for details on center taps connection.
=== PCI Express - J7 ===
!Notes
|-
|1, 2 || 3.3V_LCD3V_LCD1 || +3.3V || -
|-
|3, 4, 7, 10,<br>13, 16, 19 || DGND|| Ground || -
|}
=== J12 J56 ===
J12 J56 is a 2x1-pn 2.54mm pitch connector. The following table reports the connector's pinout:
{| class="wikitable"
|}
=== MLB CAM interface - J13 J16 ===J13 J16 is a QSH–020–01–L–D–A 36-pin 0,50 mm Hi-speed socket. It is connected to the MLB Port50mm pitch vertical connector.
The following table reports the connector's pinout:
!Notes
|-
|1 ||MLB_SN SPI_MOSI_IPU2_CS1<br>[CSI_D15] || - CAM DATA[15] || -
|-
|2 ||ENET_TXD1//1V2_ETH CSI_D14|| - CAM DATA[14] || -
|-
|3 ||MLB_SP SPI1_CS_IPU2_CSI1|| - || -
|-
|4, 5, 7, 8,<br>12, 13, 14, 15,<br>16, 18, 20, 21,<br>22, 23, 25, 26,<br>27, 28, 29, 30,<br>31, 32, 36 ||N.C CMOS_RST#_IPU2_CSI1|| - CMOS Reset || -
|-
|9 5 ||MLB_DN SPI1_CLK_IPU2_CS1|| - || -
|-
|11 6 ||MLB_DP SPI1_MISO_IPU2_CS1|| - || -
|-
|17 ||MLB_CN || - || -|-|19 ||MLB_CP || - || -|-|24 ||EIM_CS1 || - || -|-|25 ||GPIO_7//FLEXCAN1_H || - || -|-|33 ||KEY_COL3/I2C2_SCL|| - || -|-|34 ||GPIO_17 || - || -|-|35 ||KEY_ROW3/I2C2_SDA || - || -|-|37, 38, 39 ||NVCC_AXEL_I/O_3.3V/1.8V || - || -|-|40 ||EXT_12V || - || -|-|41, 42, 43, 44 ||DGND || Ground || -|-|} === CAM interface - J16 === J16 is a 36-pin 0.50mm pitch vertical connector.  The following table reports the connector's pinout: {| class="wikitable" |-!Pin# !Pin name!Function!Notes|-|1 || CSI_D15,<br>SPI_MOSI_IPU2_CS1 || CAM DATA[15] || -|-|2 || CSI_D14|| CAM DATA[14] || -|-|3 || SPI1_CS_IPU2_CSI1|| - || -|-|4 || CMOS_RST#_IPU2_CSI1|| CMOS Reset || -|-|5 || SPI1_CLK_IPU2_CS1|| - || -|-|6 || SPI1_CLK_IPU2_CS1|| - || -|-|7 || CMOS_I2C_SDA|| I2C DATA || -
|-
|8 || CMOS_I2C_SCL|| I2C CLOCK || -
|}
=== USB MIPI camera connector - J26 J53 ===
J26 J53 is a standard USB Mini AB 33-pin 0.50mm pitch ZIF connector.
The following table reports the connector's pinout:
!Notes
|-
|1 ||VIN_USBCSI_CLK0P || Power Supply - || -
|-
|2 ||USBDN CSI_CLK0M || USB Data- || -
|-
|3 4 ||USBDP CSI_D0P || USB Data+ - || -
|-
|4 5 ||N.C. CSI_D0M || - || -
|-
|5 7 ||DGND CSI_D1P || Ground - || -
|-
|6, 7, 8, 9 ||RING CSI_D1M || Shield to Ground - || -
|-
|}10 || CSI_D2P || - || - === UART3 |- J28 === J28 is a standard DB9 connector for the RS232 two|11 || CSI_D2M || -wires UART3 port. The following table reports the connector's pinout: {| class="wikitable" | -
|-
!Pin# !Pin name!Function!Notes|13 || CSI_D3P || - || -
|-
|1, 4, 6, 914 || CSI_D3M || - || -|N.C.-|N.C.16 || DSI_D1P || - ||-
|-
|217 |UART_EXT_RX|Receive lineDSI_D1M |Connected to protection diode array| - || -
|-
|319 |UART_EXT_TX|Transmit lineDSI_D0P |Connected to protection diode array| - || -
|-
|520 |DGND|GroundDSI_D0M || - || -
|-
|722 |UART_EXT_RTS|UART3 RTSDSI_CLK0P || - || -
|-
|823 |UART_EXT_CTS|UART3 CTSDSI_DCK0M || - || -
|-
|} === USB OTG 3, 6, 9, 12<br>15, 18, 21, 24 || DGND || - J29 === J29 is a standard USB Micro AB connector. The following table reports the connector's pinout: {| class="wikitable" | -
|-
!Pin# !Pin name!Function!Notes|25 || KEY_COL3/I2C2_SCL || - || -
|-
|1 26 ||USB_OTG_VBUS_FKEY_ROW3/I2C2_SDA || Power Supply - || -
|-
|2 27, 28 ||OTG_DM3.3V || USB Data- || -
|-
|3 29 ||OTG_DPGPIO_19 || USB Data+ - || -
|-
|4 30 ||OTG_ID GPIO_18 || OTG ID signal - || -
|-
|5 31 ||USB_OTG_DGNGPIO_16 || Ground - || -
|-
|632, 7, 8, 9 33 ||USB_OTG_SHIELD5V || Shield to Ground - || -
|-
|}
=== SOM Power Voltage Selector USB OTG - J32 J29 === J29 is a standard USB Micro AB connector.
J32 is a 4x2-pin 2.54 pitch vertical header. The following table reports the connector's pinout:
{| class="wikitable"
!Notes
|-
|1 || -DGND || - || -|-|2 || -|| - Ground || -
|-
|3 2 || -OTG_ID || - USB OTG ID || -
|-
|4 3 || -USB_OTG_DP || - USB OTG Data+ || -
|-
|5 4 || -USB_OTG_DN || USB OTG Data- || -
|-
|6 5 || -USB_OTG_VBUS|| - Power Supply || -
|-
|6, 7 || -|| - || -|-|, 8 , 9 || -USB_OTG_SHIELD || - Shield to Ground || -
|-
|}
=== SOM Power Voltage Selector - J32 === J32 is a 4x2-pin 2.54 pitch vertical header for SOM power voltage selection. The available configurations are the following:
* all open: 2.8V
* 1-2 closed: 3.0V
|7 || NVCC_EIM_EXT || - || -
|-
|8 || SD3_DATA6 SD4_DATA2 || - || -
|-
|9 || RGMII_MDC || - || -
|-
|10 || SD3_DATA7 SD4_DATA1 || - || -
|-
|11 || RGMII_MDIO || - || -
|14 || NVCC_LCD_EXT || - || -
|-
|15 || DATA0SD4_DATA0/NANDF_DQS || - || -
|-
|16 || KEY_COL3/I2C2_SCL || - || -
|13 || WDT_WDI//VDDPU || - || -
|-
|14 || DGND SW2_1.8V/3.3V || Ground - || -
|-
|15 || EIM_D16 || - || -
|17 || EIM_D18 || - || -
|-
|18 || DGND NOR_WP || Ground - || -
|-
|19 || DGND || Ground || -
!Function
!Notes
|-
|1, 2 ||3.3V_LCD0 || +3.3V || -
|-
|1, 2, 5, 8,<br>11, 14, 17, 19,<br>20 ||DGND || Ground || -
|}
=== IPU1_CSI0 (1/2) LVDS0 - J50 J54 ===
J50 J54 is a 10x2DF13A-pin 2.54mm pitch vertical 20DP header. The following table reports the connector's pinout:
{| class="wikitable"
!Notes
|-
|1 || CSI0_DAT11 || CAM DATA[11] || -|-|, 2 || R_CMOS_CLK_IPU1_CSI0 3.3V_LCD0 || CMOS Clock || -|-|+3 || CSI0_DAT10 || CAM DATA[10] || -|-|4 || DGND || Ground || -|-|5 || CSI0_DAT9 || CAM DATA[9] .3V || -
|-
|6 3, 4, 7, 10,<br>13, 16, 19, 21, 22 || CMOS_I2C_SDADGND || I2C DATAGround || -
|-
|7 5 || CSI0_DAT8 LVDS0_TX0_N || CAM DATA[8] TX0- || -
|-
|8 6 || CMOS_I2C_SCLLVDS0_TX0_P || I2C CLOCK TX0+ || -
|-
|9 || CSI0_DAT7 LVDS0_TX1_P || CAM DATA[7] TX1+ || -
|-
|10 8 || CMOS_RST#_IPU1_CSI0 LVDS0_TX1_N || CMOS_RST#TX1- || -
|-
|11 || CSI0_DAT6 LVDS0_TX2_N|| CAM DATA[6] TX2- || -
|-
|12 || CMOS_OE#_IPU1_CSI0 LVDS0_TX2_P|| CMOS_OE# TX2+ || -
|-
|13 14 || CSI0_DAT5 LVDS0_CLK_N || CAM DATA[5] Clock- || -
|-
|14 15 || DGND LVDS0_CLK_P || Ground Clock+ || -
|-
|15 17 || CSI0_DAT4 LVDS0_P17 || CAM DATA[4] - || -
|-
|16 18 || CAM_VCC_2.8V_IPU1_CSI0 LVDS0_P18 || 2.8V Power Supply - || -
|-
|17 || EIM_D30 || CAM DATA[3] || -|-|18 || CAM_VCC_2.8V_IPU1_CSI0 |20 | 2.8V Power Supply |LVDS0_P20 | -|-|19 || EIM_D31 || CAM DATA[2] || -|-|20 || DGND || Ground || -
|-
|}
=== IPU1_CSI0 (2/2) - J51 J19 ===
J51 J19 is a 10x225x2-pin 2.54mm pitch vertical header. The following table reports the connector's pinout:
{| class="wikitable"
!Notes
|-
|1 , 2, 6, 15, 24<br>29, 40, 49,50 || EIM_D26 DGND || CAM DATA[1] Ground || -|-|3, 5, 7, 17, 19<br>31, 33, 35 || N.C. || Not connected || -
|-
|2 20, 22, 26, 28<br>30, 34 || DGND N.C. || Ground Not connected || -
|-
|3 4 || EIM_D27CSI0_PIXCLK || CAM DATA[0] CMOS Clock || -
|-
|4, 5, 6 9 || CAM_VCC_IPU1_CSI0CSI0_DAT15 || 3.3V Power Supply CAM DATA[15] || -
|-
|7 10 || CSI0_PIXCLKCAM_VCC_IPU1_CSI0 || CAM Pixel Clock IPU1 CSI0 Power Supply || -
|-
|8 11 || DGND CSI0_DAT16 || Ground CAM DATA[16] || -
|-
|9 12 || CSI0_MCLKCSI0_VSYNC || CAM Hsync CSI0 Vertical Sync || -
|-
|10 13 || CAM_VCC_1.8V_IPU1_CSI0CSI0_DAT17 || 1.8V Power Supply CAM DATA[17] || -
|-
|11 14 || CSI0_VSYNCCSI0_MCLK || CAM Vsync CSI0 MCLK || -
|-
|12 16 || CAM_VCC_1.8V_IPU1_CSI0GPIO_19 || 1.8V Power Supply GPIO 19 || -
|-
|13 18 || CSI0_DAT12EIM_D26 || CAM DATA[12] EIM D26 || -
|-
|14 21 || CSI0_DAT13CSI0_DAT9 || CAM DATA[139] || -
|-
|15 23 || CSI0_DAT16CSI0_DAT10 || CAM DATA[1610] || -
|-
|16 25 || CSI0_DAT19CSI0_DAT11 || CAM DATA[1911]|| -
|-
|17 27 || CSI0_DAT17CSI0_DAT12 || CAM DATA[1712]|| -
|-
|18 32 || CSI0_DATA_ENCAM_VCC_IPU1_CSI0 || CAM DATA Enable - || -
|-
|19 36 || CSI0_DAT18EIM_D27 || CAM DATA[18] EIM D27 || -
|-
|20 37 || NVCC_EIM_EXTCSI0_DAT4 || CSI1_VEXT CAM DATA[4] || -
|-
|38 || CSI0_DAT6 || CAM DATA[6] || -|-|39 || CSI0_DAT5 || CAM DATA[5] || -|-|41 || CSI0_DAT18 || CAM DATA[18] || -|-|42 || CSI0_DAT7 || CAM DATA[6] || -|-|43 || CSI0_DAT19 || CAM DATA[19] || -|-|44 || CSI0_DAT8 || CAM DATA[8] || -|-|45 || CSI0_DAT13 || CAM DATA[13] || -|-|46 || KEY_ROW3/I2C2_SDA || - || -|-|47 || CSI0_DAT14 || CAM DATA[14] || -|-|48 || KEY_COL3/I2C2_SCL || - || -|-|} === Boot MicroSD - J52 === J52 is a microSD memory card connector. The following table reports the connector's pinout: {| class="wikitable"
|-
!Pin#
!Notes
|-
|1 ||SD2_DAT2SD1_DAT2||| DATA[2] || -
|-
|2 ||SD2_DAT3SD1_DAT3||| Card Detect/DATA[3] || -
|-
|3 ||SD2_CMDSD1_CMD||| CMD line || -
|-
|4 ||NVCC_AXEL_I/O_33.3V/1.8V||| Power Supply || -
|-
|5 ||SD2_CLKSD1_CLK||| Clock || -
|-
|6, 9, 10, 11, 12 ||DGND||| - || -
|-
|7 ||SD1_DAT0||| DATA[0] || -
|-
|8 ||SD1_DAT1||| DATA[1] || -
|-
|13 ||3.3V|| - || -
|-
|}
 
=== General purpose SD connector - J55 ===
 
J52 is a microSD memory card connector. The following table reports the connector's pinout:
 
{| class="wikitable"
|-
!Pin#
!Pin name
!Function
!Notes
|-
|1 ||SD2_DAT3||| DATA[3] || -
|-
|2 ||SD2_CMD||| CMD line || -
|-
|3, 6 ||DGND||| Ground || -
|-
|4 ||3.3V||| Power Supply || -
|-
|5 ||SD2_CLK||| Clock || -
|-
|7 ||SD2_DAT0||| DATA[0] || -
|8 ||SD2_DAT1||| DATA[1] || -
|-
|13 9 ||GPIO_0SD2_DAT2|| - | DATA[2] ||Pull up to 3.3V with 10K Ohm -
|-
|}
=== Pin strip connectors SPI PMOD - JP17 ===
==== J-PROG-MICRO1 ==== J-PROG-MICRO1 JP17 is a 3x212-pin, 26x2x2.54mm 54 pitch vertical header, pinstrip connector. The following table reports the pinout of the connector's pinout:
{| class="wikitable"
!Notes
|-
|1 || BKGD_JM60SD2_DATA1||| - || -
|-
|2 || DGNDGPIO_17 || Ground | - || -
|-
|3, 5 || N.C. SD2_CMD ||| - || -
|-
|4 , 6, 8 || RST_JM60N.C.|| - | Not connected || -
|-
|6 5 || VIN_USBSD2_DATA0 ||| || -|-|7 ||SD2_CLK ||| - || -|-|9, 10 ||DGND ||| Ground || -|-|11, 12 ||+3.3V ||| - || -
|-
|}
 
=== Pin strip connectors ===
==== J-PROG-PMIC1 ====
|1 || 2V8-4V5|| - || -
|-
|2 || MIC_PROG_GATE_CTRlPMIC_PROG_GATE_CTRl|| - || -
|-
|3 || DGND|| Ground || -
!Notes
|-
|1 || - || - || Connetted Connected to pin 3
|-
|2 || DGND|| Ground|| -
|-
|3 || - || - || Connetted Connected to pin 1
|-
|4, 6, 8, 10,<br>12, 14, 16 || NVCC_CSI_EXT|| - || -
!Notes
|-
|1 || - || - || Connetted Connected to pin 3
|-
|2 || DGND|| Ground|| -
|-
|3 || - || - || Connetted Connected to pin 1
|-
|4, 6, 8, 10,<br>12, 14, 16 || NVCC_EIM_EXT|| - || -
|}
==== MIPI CSI - JP7 ====
 
JP7 is a 8x2-pin 2.54mm pitch header pinstrip connector. The following table reports the connector's pinout:
 
{| class="wikitable"
|-
!Pin#
!Pin name
!Function
!Notes
|-
|1 || CSI_D3P || Data3 + ||
|-
|2, 5, 8, 11,<br> 14, 16 || DGND|| Ground|| -
|-
|3 || CSI_D3N || Data3- ||
|-
|4 || CSI_D2P|| Data2+ || -
|-
|6 || CSI_D2M|| Data2-|| -
|-
|7 || CSI_D1P|| Data1+|| -
|-
|9 || CSI_D1M|| Data1- || -
|-
|13 || CSI_CLK0P|| Clock+ || -
|-
|15 || CSI_CLK0M|| Clock- || -
|-
|}
==== EXPANSION CONNECTOR - JP8 ====
|}
==Boot configurations == MIPI DSI The AxelEVB- JP11 ====Lite carrier board can host two different SoM's, [[:Category:AxelUltra|Axel Ultra]] and [[:Category:AxelLite|Axel Lite]].
JP11 is a 8x2-pin 2.54mm pitch header pinstrip connector. The following table reports sections detail boot configuration options, which differ depending on the connector's pinout:SoM.
{| class="wikitable" ==Axel Ultra======= uSD card ==== |Dip-switch configuration:!Pin# !Pin name<pre>S5[1..8] : On Off On On On On Off Off!FunctionS6[1..8] : Off Off On On Off On On On!NotesS7[1..8] : Off Off On On On On On On |-S8[1..8] : On Off On On Off On On On|S9[1, ..2, 7, 8,] : Off Off<br/pre> 12, 13, 15, 16 || DGND || Ground || |-|3 || DSI_D1M || Data1 - || ==== SPI NOR flash ====|-|4 || DSI_CLOCK0M || Clock Dip- ||switch configuration:|-|5 || DSI_D1P || Data1 + ||<pre>|-S5[1..8] : On On Off Off On On Off Off |6 || DSI_CLOCK0P S6[1..8] : Off Off On On Off On On || Clock + ||On|-S7[1..8] : Off Off On Off Off Off On Off|9 || DSI_DOP|| Data0 + ||S8[1..8] : On Off On On Off On On On|-S9[1..2] : Off Off|10 || NVCC_AXEL_I</O_3.3V/1.8|| - ||pre>|-===Axel Lite===|11 || DSI_D0M|| Data0 In this case, it is required to use the [[AxelEVB- |||Lite-|14 |Adapter (AxelLite)| SW4_xV/1specific revision A adapter]] to plug the SoM.8V || Regarding the boot options, please refer to [[AxelEVB- |||Lite-Adapter_(AxelLite)#Revision_A_2|}this section]].
==SchematicsTechnical documents ==
===Schematics===* ORCAD: http://wwwmirror.dave.eu/systemaxel/hw/filesAxelEVB/arearev-riservataA/axelevb-litelite_S-EVBA1000C1R_1.0.98.3-XELK-dsndsn_.zip* PDF: http://wwwmirror.dave.eu/systemaxel/hw/filesAxelEVB/arearev-riservataA/axelevb-litelite_S-SEVBA1000C1R_1.EVBA1000C0R-0.9.38.pdf
===BOM===* AxelEVB-Lite: http://wwwmirror.dave.eu/systemaxel/hw/filesAxelEVB/arearev-riservataA/axelevbAXELEVB-lite_BOM_SLITE_S.EVBA1000C0R_0EVBA1000C1R.91.30.CSV_8.zip
===Layout===* http://wwwmirror.dave.eu/systemaxel/hw/filesAxelEVB/arearev-riservataA/axelevb-lite_CS151613_assem_viewlite_S-EVBA1000C1R_CS151613A_AssemView.pdf
===Mechanical===* DXF: http://wwwmirror.dave.eu/systemaxel/hw/filesAxelEVB/arearev-riservataA/axelevb-lite_2D_CS151613lite-S-EVBA1000C1R_CS151613A-2D.dxf_.zip* IDF (3D): http://wwwmirror.dave.eu/systemhw/filesaxel/areaAxelEVB/rev-riservataA/axelevb-lite_3D_CS151613lite-S-EVBA1000C1R_CS151613A-3D.idf_.zip
U0001
Bureaucrats, dave_user, Administrators
4,650
edits
Retrieved from "https://wiki.dave.eu/index.php/Special:MobileDiff/3287...9222"

Navigation menu