Changes

Jump to: navigation, search

AxelEVB-Lite

1,197 bytes added, 10:55, 5 September 2019
no edit summary
{{ImportantMessage|text=This page provides information for the AxelEVB-Lite carrier board model S-EVBA1000C1R (BOM 1.0.4), provided with XELK kits version 2.1.0 and above.
 
For AxelEVB-Lite manufactured before the release of XELK 2.1.0, please refer to [[AxelEVB-Lite_rev.0|this page]].
}}
 
 
{{InfoBoxTop}}
{{AppliesToAxel}}
{{AppliesToAxelLite}}
{{AppliesToAxelEsatta}}
{{InfoBoxBottom}}
[[File:Axelevb-lite-01.png|500px|frameless|border]]==Introduction==
==Introduction==AxelEVB-Lite is a carrier board designed to host [[File:Axel Ultra SOM-evb-lite-revA 02.jpg|Axel Ultra]] and [[Axel Lite SOM500px|Axel Lite]] (through an adapter) SoMs. It exports some specific peripherals connectors and acts as an adaptation board used in combination with [[:Category:Dacuframeless|Dacuborder]] carrier board.
{{ImportantMessage|text=This page provides information for the AxelEVB-Lite is a carrier board model S-EVBA1000C1R designed to host [[:Category:AxelUltra|AXEL ULTRA]] and [[:Category:AxelLite|AXEL LITE]] (BOM 1.0.4through an adapter), provided with XELK kits version 2SoMs.1.0 It exports some specific peripherals connectors and above. If you have a acts as an adaptation board from a previous version of the XELK kit (older than 2.1.0), please contact used in combination with [[mailto:support-axel@dave.eu support-axel@dave.euCategory:Dacu|Dacu]]carrier board.}}
==Block Diagram==
The following picture shows Axel-EVB-Lite's block diagram:
[[File:Axelevb-lite-block diagram.png|700px|frameless|border|centre]]
== Features ==
* 1x USB OTG,1x USB HOST
* Serial port (RS232)
* JTAG
* HDMI connector
* SATA connector
|-
|37, 38, 39, 40 || SH_CAM || Shield to Ground || -
|-
|}
 
=== MIPI camera connector - J53 ===
 
J53 is a 33-pin 0.50mm pitch ZIF connector
 
The following table reports the connector's pinout:
 
{| class="wikitable"
|-
!Pin#
!Pin name
!Function
!Notes
|-
|1 || CSI_CLK0P || - || -
|-
|2 || CSI_CLK0M || - || -
|-
|4 || CSI_D0P || - || -
|-
|5 || CSI_D0M || - || -
|-
|7 || CSI_D1P || - || -
|-
|8 || CSI_D1M || - || -
|-
|10 || CSI_D2P || - || -
|-
|11 || CSI_D2M || - || -
|-
|13 || CSI_D3P || - || -
|-
|14 || CSI_D3M || - || -
|-
|16 || DSI_D1P || - || -
|-
|17 || DSI_D1M || - || -
|-
|19 || DSI_D0P || - || -
|-
|20 || DSI_D0M || - || -
|-
|22 || DSI_CLK0P || - || -
|-
|23 || DSI_DCK0M || - || -
|-
|3, 6, 9, 12<br>15, 18, 21, 24 || DGND || - || -
|-
|25 || KEY_COL3/I2C2_SCL || - || -
|-
|26 || KEY_ROW3/I2C2_SDA || - || -
|-
|27, 28 || 3.3V || - || -
|-
|29 || GPIO_19 || - || -
|-
|30 || GPIO_18 || - || -
|-
|31 || GPIO_16 || - || -
|-
|32, 33 || 5V || - || -
|-
|}
|}
=== IPU1_CSI0 LVDS0 - J19 J54 ===
J19 J54 is a 25x210x2 DF13A-pin 2.54mm pitch vertical 20DP header. The following table reports the connector's pinout:
{| class="wikitable"
!Notes
|-
|1, 2 ||3.3V_LCD0 || +3.3V || -|-|3, 4, 7, 10,<br>13, 16, 19, 21, 22 ||DGND || Ground || -|-|5 || LVDS0_TX0_N || TX0- || -|-|6 || LVDS0_TX0_P || TX0+ || -|-|9 || LVDS0_TX1_P || TX1+ || -|-|8 || LVDS0_TX1_N || TX1- || -|-|11 || LVDS0_TX2_N|| TX2- || -|-|12|| LVDS0_TX2_P|| TX2+ || -|-|14 || LVDS0_CLK_N || Clock- || -|-|15 || LVDS0_CLK_P || Clock+ || -|-|17 || LVDS0_P17 || - || -|-|18 ||LVDS0_P18 || - || -|-|20 || LVDS0_P20 || - || -|-|} === IPU1_CSI0 - J19 === J19 is a 25x2-pin 2.54mm pitch vertical header. The following table reports the connector's pinout: {| class="wikitable" |-!Pin# !Pin name!Function!Notes|-|1, 2, 6, 15, 24<br>29, 40, 49,50 || DGND || Ground || -
|-
|3, 5, 7, 17, 19<br>31, 33, 35 || N.C. || Not connected || -
|}
=== IPU1_CSI0 (2/2) Boot MicroSD - J51 J52 ===
J51 J52 is a 10x2-pin 2.54mm pitch vertical headermicroSD memory card connector. The following table reports the connector's pinout:
{| class="wikitable"
!Notes
|-
|1 || EIM_D26 SD1_DAT2||| CAM DATA[12] || -|-|2 || DGND || Ground || -
|-
|3 2 ||SD1_DAT3| EIM_D27|| CAM Card Detect/DATA[03] || -
|-
|4, 5, 6 3 || CAM_VCC_IPU1_CSI0SD1_CMD|| 3.3V Power Supply | CMD line || -
|-
|7 4 || CSI0_PIXCLK3.3V|| CAM Pixel Clock | Power Supply || -
|-
|8 5 || DGND SD1_CLK|| Ground | Clock || -
|-
|6, 9 || CSI0_MCLK|| CAM Hsync || -|-|, 10 , 11, 12 || CAM_VCC_1.8V_IPU1_CSI0DGND|| 1.8V Power Supply || -|-|11 || CSI0_VSYNC|| CAM Vsync || -
|-
|12 7 || CAM_VCC_1.8V_IPU1_CSI0SD1_DAT0|| 1.8V Power Supply | DATA[0] || -
|-
|13 8 || CSI0_DAT12SD1_DAT1||| CAM DATA[121] || -
|-
|14 || CSI0_DAT13|| CAM DATA[13] || -|-|15 || CSI0_DAT16|| CAM DATA[16] || -|-|16 || CSI0_DAT19|| CAM DATA[19]3.3V|| -|-|17 || CSI0_DAT17|| CAM DATA[17]|| -|-|18 || CSI0_DATA_EN|| CAM DATA Enable || -|-|19 || CSI0_DAT18|| CAM DATA[18] || -|-|20 || NVCC_EIM_EXT|| CSI1_VEXT || -
|-
|}
=== MicroSD General purpose SD connector - J52 J55 ===
J52 is a microSD memory card connector. The following table reports the connector's pinout:
!Notes
|-
|1 ||SD2_DAT2SD2_DAT3||| DATA[23] || -
|-
|2 ||SD2_DAT3SD2_CMD||| Card Detect/DATA[3] CMD line || -
|-
|3 , 6 ||SD2_CMDDGND||| CMD line Ground || -
|-
|4 ||NVCC_AXEL_I/O_33.3V/1.8V||| Power Supply || -
|-
|5 ||SD2_CLK||| Clock || -
|-
|6, 9, 10, 11, 12 ||DGND||| - || -
|-
|7 ||SD2_DAT0||| DATA[0] || -
|8 ||SD2_DAT1||| DATA[1] || -
|-
|13 9 ||GPIO_0SD2_DAT2|| - | DATA[2] ||Pull up to 3.3V with 10K Ohm -
|-
|}
=== Pin strip connectors SPI PMOD - JP17 ===
==== J-PROG-MICRO1 ==== J-PROG-MICRO1 JP17 is a 3x212-pin, 26x2x2.54mm 54 pitch vertical header, pinstrip connector. The following table reports the pinout of the connector's pinout:
{| class="wikitable"
!Notes
|-
|1 || BKGD_JM60SD2_DATA1||| - || -
|-
|2 || DGNDGPIO_17 || Ground | - || -
|-
|3, 5 || N.C. SD2_CMD ||| - || -
|-
|4 , 6, 8 || RST_JM60N.C.|| - | Not connected || -
|-
|6 5 || VIN_USBSD2_DATA0 ||| || -|-|7 ||SD2_CLK ||| - || -|-|9, 10 ||DGND ||| Ground || -|-|11, 12 ||+3.3V ||| - || -
|-
|}
 
=== Pin strip connectors ===
==== J-PROG-PMIC1 ====
|1 || 2V8-4V5|| - || -
|-
|2 || MIC_PROG_GATE_CTRlPMIC_PROG_GATE_CTRl|| - || -
|-
|3 || DGND|| Ground || -
!Notes
|-
|1 || - || - || Connetted Connected to pin 3
|-
|2 || DGND|| Ground|| -
|-
|3 || - || - || Connetted Connected to pin 1
|-
|4, 6, 8, 10,<br>12, 14, 16 || NVCC_CSI_EXT|| - || -
!Notes
|-
|1 || - || - || Connetted Connected to pin 3
|-
|2 || DGND|| Ground|| -
|-
|3 || - || - || Connetted Connected to pin 1
|-
|4, 6, 8, 10,<br>12, 14, 16 || NVCC_EIM_EXT|| - || -
|}
==== MIPI CSI - JP7 ====
 
JP7 is a 8x2-pin 2.54mm pitch header pinstrip connector. The following table reports the connector's pinout:
 
{| class="wikitable"
|-
!Pin#
!Pin name
!Function
!Notes
|-
|1 || CSI_D3P || Data3 + ||
|-
|2, 5, 8, 11,<br> 14, 16 || DGND|| Ground|| -
|-
|3 || CSI_D3N || Data3- ||
|-
|4 || CSI_D2P|| Data2+ || -
|-
|6 || CSI_D2M|| Data2-|| -
|-
|7 || CSI_D1P|| Data1+|| -
|-
|9 || CSI_D1M|| Data1- || -
|-
|13 || CSI_CLK0P|| Clock+ || -
|-
|15 || CSI_CLK0M|| Clock- || -
|-
|}
==== EXPANSION CONNECTOR - JP8 ====
|}
==Boot configurations == MIPI DSI  === uSD === Dip- JP11 switch configuration: <pre>S5[1..8] : On Off On On On On Off OffS6[1..8] : Off Off On On Off On On OnS7[1..8] : Off Off On On On On On On S8[1..8] : On Off On On Off On On OnS9[1..2] : Off Off</pre> ===NOR SPI===
JP11 is a 8x2Dip-pin 2.54mm pitch header pinstrip connector. The following table reports the connector's pinoutswitch configuration:
{| class="wikitable" <pre>|-S5[1..8] : On On Off Off On On Off Off !Pin# S6[1..8] : Off Off On On Off On On On!Pin nameS7[1..8] : Off Off On Off Off Off On Off!Function!Notes|-S8[1..8] : On Off On On Off On On On|S9[1, ..2, 7, 8,] : Off Off<br/pre> 12, 13, 15, 16 || DGND || Ground || | == XELK 2.0.0 == ===Schematics===* ORCAD: http://mirror.dave.eu/axel/AxelEVB/XELK-|3 || DSI_D1M || Data1 2.0.0/axelevb- || |lite-|0.9.4 || DSI_CLOCK0M || Clock - ||XELK-dsn.zip|* PDF: http://mirror.dave.eu/axel/AxelEVB/XELK-2.0.0/axelevb-lite-S.EVBA1000C0R.0.9.4.pdf|5 || DSI_D1P || Data1 + |||===BOM===* AxelEVB-|6 || DSI_CLOCK0P || Clock + |||Lite: http://mirror.dave.eu/axel/AxelEVB/XELK-2.0.0/axelevb-lite_BOM_S.EVBA1000C0R_0.9.4.CSV_.zip|9 || DSI_DOP|| Data0 + |||-===Layout===|10 || NVCC_AXEL_I* http:/O_3/mirror.3Vdave.eu/1axel/AxelEVB/XELK-2.0.8|| 0/axelevb- ||lite_CS151613_assem_view.pdf|-|11 || DSI_D0M|| Data0 - ||===Mechanical===|-|14 || SW4_xV* DXF: http://1mirror.dave.8V || eu/axel/AxelEVB/XELK- |||2.0.0/axelevb-|}lite_3D_CS151613.zip
==SchematicsXELK 2.2.0 ==
===Schematics===* ORCAD: http://wwwmirror.dave.eu/systemaxel/filesAxelEVB/areaXELK-riservata2.2.0/axelevb-litelite_S-EVBA1000C1R_1.0.98.3-XELK-dsndsn_.zip* PDF: http://wwwmirror.dave.eu/systemaxel/filesAxelEVB/areaXELK-riservata2.2.0/axelevb-litelite_S-SEVBA1000C1R_1.EVBA1000C0R-0.9.38.pdf
===BOM===* AxelEVB-Lite: http://wwwmirror.dave.eu/systemaxel/filesAxelEVB/areaXELK-riservata2.2.0/axelevbAXELEVB-lite_BOM_SLITE_S.EVBA1000C0R_0EVBA1000C1R.91.30.CSV_8.zip
===Layout===* http://wwwmirror.dave.eu/systemaxel/filesAxelEVB/areaXELK-riservata2.2.0/axelevb-lite_CS151613_assem_viewlite_S-EVBA1000C1R_CS151613A_AssemView.pdf
===Mechanical===* DXF: http://wwwmirror.dave.eu/systemaxel/filesAxelEVB/areaXELK-riservata2.2.0/axelevb-lite_2D_CS151613lite-S-EVBA1000C1R_CS151613A-2D.dxf_.zip* IDF (3D): http://wwwmirror.dave.eu/systemaxel/filesAxelEVB/areaXELK-riservata2.2.0/axelevb-lite_3D_CS151613lite-S-EVBA1000C1R_CS151613A-3D.idf_.zip
U0007
Bureaucrats, dave_user, Administrators
8,154
edits
Retrieved from "https://wiki.dave.eu/index.php/Special:MobileDiff/3404...8859"

Navigation menu