Changes

Jump to: navigation, search

AxelEVB-Lite

1,429 bytes added, 10:55, 5 September 2019
no edit summary
{{ImportantMessage|text=This page provides information for the AxelEVB-Lite carrier board model S-EVBA1000C1R (BOM 1.0.4), provided with XELK kits version 2.1.0 and above.
 
For AxelEVB-Lite manufactured before the release of XELK 2.1.0, please refer to [[AxelEVB-Lite_rev.0|this page]].
}}
 
 
{{InfoBoxTop}}
{{AppliesToAxel}}
{{AppliesToAxelLite}}
{{AppliesToAxelEsatta}}
{{InfoBoxBottom}}
[[File:Axelevb-lite-01.png|500px|frameless|border]]==Introduction==
==Introduction==AxelEVB-Lite is a carrier board designed to host [[File:Axel Ultra SOM-evb-lite-revA 02.jpg|Axel Ultra]] and [[Axel Lite SOM500px|Axel Lite]] (through an adapter) SoMs. It exports some specific peripherals connectors and acts as an adaptation board used in combination with [[:Category:Dacuframeless|Dacuborder]] carrier board.
{{ImportantMessage|text=This page provides information for the AxelEVB-Lite is a carrier board model S-EVBA1000C1R designed to host [[:Category:AxelUltra|AXEL ULTRA]] and [[:Category:AxelLite|AXEL LITE]] (BOM 1.0.4through an adapter), provided with XELK kits version 2SoMs.1.0 It exports some specific peripherals connectors and above. If you have a acts as an adaptation board from a previous version of the XELK kit (older than 2.1.0), please contact used in combination with [[mailto:support-axel@dave.eu support-axel@dave.euCategory:Dacu|Dacu]]carrier board.}}
==Block Diagram==
The following picture shows Axel-EVB-Lite's block diagram:
[[File:Axelevb-lite-block diagram.png|700px|frameless|border|centre]]
== Features ==
* 1x USB OTG,1x USB HOST
* Serial port (RS232)
* JTAG
* HDMI connector
* SATA connector
|}
=== USB OTG MIPI camera connector - J29 J53 ===
J29 J53 is a standard USB Micro AB 33-pin 0.50mm pitch ZIF connector.
The following table reports the connector's pinout:
!Notes
|-
|1 ||DGND CSI_CLK0P || Ground - || -|-|2 || CSI_CLK0M || - || -|-|4 || CSI_D0P || - || -|-|5 || CSI_D0M || - || -|-|7 || CSI_D1P || - || -|-|8 || CSI_D1M || - || -|-|10 || CSI_D2P || - || -|-|11 || CSI_D2M || - || -|-|13 || CSI_D3P || - || -
|-
|2 14 ||OTG_ID CSI_D3M || USB OTG ID - || -
|-
|3 16 ||USB_OTG_DP DSI_D1P || USB OTG Data+ - || -
|-
|4 17 ||USB_OTG_DN DSI_D1M || USB OTG Data- || -
|-
|5 19 ||USB_OTG_VBUSDSI_D0P || Power Supply - || -
|-
|6, 7, 8, 9 20 ||USB_OTG_SHIELD DSI_D0M || Shield to Ground - || -
|-
|} === SOM Power Voltage Selector 22 || DSI_CLK0P || - J32 === J32 is a 4x2|| -pin 2.54 pitch vertical header. The following table reports the connector's pinout: {| class="wikitable"
|-
!Pin# !Pin name!Function!Notes|23 || DSI_DCK0M || - || -
|-
|1 3, 6, 9, 12<br>15, 18, 21, 24 || -DGND || - || -
|-
|2 25 || -KEY_COL3/I2C2_SCL || - || -
|-
|3 26 || -KEY_ROW3/I2C2_SDA || - || -
|-
|4 27, 28 || -3.3V || - || -
|-
|5 29 || -GPIO_19 || - || -
|-
|6 30 || -GPIO_18 || - || -
|-
|7 31 || -GPIO_16 || - || -
|-
|8 32, 33 || -5V || - || -
|-
|}
SOM power voltage selection:* all open: 2.8V* 1=== USB OTG -2 closed: 3.0V* 3-4 closed: 3.3V* 5-6 closed: 4.2V* 7-8 closed: 4.5vJ29 ===
=== J33 ===J29 is a standard USB Micro AB connector.
J33 is a 2x1-pin 2.54 pitch vertical header. The following table reports the connector's pinout:
{| class="wikitable"
!Notes
|-
|1 || DGND|| Ground || -
|-
|2 ||OTG_ID || USB OTG ID || -|-|3 ||USB_OTG_DP || USB OTG Data+ || -|-|4 ||USB_OTG_DN || USB OTG Data- || -|-|5 ||USB_OTG_VBUS|| Power Supply || -|-|6, 7, 8, 9 ||USB_OTG_SHIELD || Shield to Ground || -|-|} === SOM Power Voltage Selector - J32 === J32 is a 4x2-pin 2.54 pitch vertical header for SOM power voltage selection. The available configurations are the following: * all open: 2.8V* 1-2 closed: 3.0V* 3-4 closed: 3.3V* 5-6 closed: 4.2V* 7-8 closed: 4.5v === J33 === J33 is a 2x1-pin 2.54 pitch vertical header. The following table reports the connector's pinout: {| class="wikitable" |-!Pin# !Pin name!Function!Notes|-|1 || DGND|| Ground || -|-|2 || 5V|| 5V Power Supply || -
|-
|}
|7 || NVCC_EIM_EXT || - || -
|-
|8 || SD3_DATA6 SD4_DATA2 || - || -
|-
|9 || RGMII_MDC || - || -
|-
|10 || SD3_DATA7 SD4_DATA1 || - || -
|-
|11 || RGMII_MDIO || - || -
|14 || NVCC_LCD_EXT || - || -
|-
|15 || DATA0SD4_DATA0/NANDF_DQS || - || -
|-
|16 || KEY_COL3/I2C2_SCL || - || -
|13 || WDT_WDI//VDDPU || - || -
|-
|14 || DGND SW2_1.8V/3.3V || Ground - || -
|-
|15 || EIM_D16 || - || -
|17 || EIM_D18 || - || -
|-
|18 || DGND NOR_WP || Ground - || -
|-
|19 || DGND || Ground || -
!Function
!Notes
|-
|1, 2 ||3.3V_LCD0 || +3.3V || -
|-
|1, 2, 5, 8,<br>11, 14, 17, 19,<br>20 ||DGND || Ground || -
|}
=== IPU1_CSI0 (1/2) LVDS0 - J50 J54 ===
J50 J54 is a 10x2DF13A-pin 2.54mm pitch vertical 20DP header. The following table reports the connector's pinout:
{| class="wikitable"
!Notes
|-
|1 , 2 || CSI0_DAT11 3.3V_LCD0 || CAM DATA[11] +3.3V || -
|-
|2 3, 4, 7, 10,<br>13, 16, 19, 21, 22 || R_CMOS_CLK_IPU1_CSI0 DGND || CMOS Clock Ground || -
|-
|3 5 || CSI0_DAT10 LVDS0_TX0_N || CAM DATA[10] TX0- || -
|-
|4 6 || DGND LVDS0_TX0_P || Ground TX0+ || -
|-
|5 9 || CSI0_DAT9 LVDS0_TX1_P || CAM DATA[9] TX1+ || -
|-
|6 8 || CMOS_I2C_SDALVDS0_TX1_N || I2C DATATX1- || -
|-
|7 11 || CSI0_DAT8 LVDS0_TX2_N|| CAM DATA[8] TX2- || -
|-
|8 12|| CMOS_I2C_SCLLVDS0_TX2_P|| I2C CLOCK TX2+ || -
|-
|9 14 || CSI0_DAT7 LVDS0_CLK_N || CAM DATA[7] Clock- || -
|-
|10 15 || CMOS_RST#_IPU1_CSI0 LVDS0_CLK_P || CMOS_RST#Clock+ || -
|-
|11 17 || CSI0_DAT6 LVDS0_P17 || CAM DATA[6] - || -
|-
|12 18 || CMOS_OE#_IPU1_CSI0 LVDS0_P18 || CMOS_OE# - || -
|-
|13 || CSI0_DAT5 || CAM DATA[5] || -|-|14 || DGND || Ground || -|-|15 || CSI0_DAT4 || CAM DATA[4] || -20 |-|16 LVDS0_P20 || CAM_VCC_2.8V_IPU1_CSI0 || 2.8V Power Supply || -|-|17 || EIM_D30 || CAM DATA[3] || -|-|18 || CAM_VCC_2.8V_IPU1_CSI0 || 2.8V Power Supply || -|-|19 || EIM_D31 || CAM DATA[2] || -|-|20 || DGND || Ground || -
|-
|}
=== IPU1_CSI0 (2/2) - J51 J19 ===
J51 J19 is a 10x225x2-pin 2.54mm pitch vertical header. The following table reports the connector's pinout:
{| class="wikitable"
!Notes
|-
|1 , 2, 6, 15, 24<br>29, 40, 49,50 || EIM_D26 DGND || CAM DATA[1] Ground || -
|-
|2 3, 5, 7, 17, 19<br>31, 33, 35 || DGND N.C. || Ground Not connected || -|-|20, 22, 26, 28<br>30, 34 || N.C. || Not connected || -
|-
|3 4 || EIM_D27CSI0_PIXCLK || CAM DATA[0] CMOS Clock || -
|-
|4, 5, 6 9 || CAM_VCC_IPU1_CSI0CSI0_DAT15 || 3.3V Power Supply CAM DATA[15] || -
|-
|7 10 || CSI0_PIXCLKCAM_VCC_IPU1_CSI0 || CAM Pixel Clock IPU1 CSI0 Power Supply || -
|-
|8 11 || DGND CSI0_DAT16 || Ground CAM DATA[16] || -
|-
|9 12 || CSI0_MCLKCSI0_VSYNC || CAM Hsync CSI0 Vertical Sync || -
|-
|10 13 || CAM_VCC_1.8V_IPU1_CSI0CSI0_DAT17 || 1.8V Power Supply CAM DATA[17] || -
|-
|11 14 || CSI0_VSYNCCSI0_MCLK || CAM Vsync CSI0 MCLK || -
|-
|12 16 || CAM_VCC_1.8V_IPU1_CSI0GPIO_19 || 1.8V Power Supply GPIO 19 || -
|-
|13 18 || CSI0_DAT12EIM_D26 || CAM DATA[12] EIM D26 || -
|-
|14 21 || CSI0_DAT13CSI0_DAT9 || CAM DATA[139] || -
|-
|15 23 || CSI0_DAT16CSI0_DAT10 || CAM DATA[1610] || -
|-
|16 25 || CSI0_DAT19CSI0_DAT11 || CAM DATA[1911]|| -
|-
|17 27 || CSI0_DAT17CSI0_DAT12 || CAM DATA[1712]|| -
|-
|18 32 || CSI0_DATA_ENCAM_VCC_IPU1_CSI0 || CAM DATA Enable - || -
|-
|19 36 || CSI0_DAT18EIM_D27 || CAM DATA[18] EIM D27 || -
|-
|20 37 || NVCC_EIM_EXTCSI0_DAT4 || CSI1_VEXT CAM DATA[4] || -
|-
|38 || CSI0_DAT6 || CAM DATA[6] || -|-|39 || CSI0_DAT5 || CAM DATA[5] || -|-|41 || CSI0_DAT18 || CAM DATA[18] || -|-|42 || CSI0_DAT7 || CAM DATA[6] || -|-|43 || CSI0_DAT19 || CAM DATA[19] || -|-|44 || CSI0_DAT8 || CAM DATA[8] || -|-|45 || CSI0_DAT13 || CAM DATA[13] || -|-|46 || KEY_ROW3/I2C2_SDA || - || -|-|47 || CSI0_DAT14 || CAM DATA[14] || -|-|48 || KEY_COL3/I2C2_SCL || - || -|-|}
=== Boot MicroSD - J52 ===
J52 is a microSD memory card connector. The following table reports the connector's pinout:
!Notes
|-
|1 ||SD2_DAT2SD1_DAT2||| DATA[2] || -
|-
|2 ||SD2_DAT3SD1_DAT3||| Card Detect/DATA[3] || -
|-
|3 ||SD2_CMDSD1_CMD||| CMD line || -
|-
|4 ||NVCC_AXEL_I/O_33.3V/1.8V||| Power Supply || -
|-
|5 ||SD2_CLKSD1_CLK||| Clock || -
|-
|6, 9, 10, 11, 12 ||DGND||| - || -
|-
|7 ||SD1_DAT0||| DATA[0] || -
|-
|8 ||SD1_DAT1||| DATA[1] || -
|-
|13 ||3.3V|| - || -
|-
|}
 
=== General purpose SD connector - J55 ===
 
J52 is a microSD memory card connector. The following table reports the connector's pinout:
 
{| class="wikitable"
|-
!Pin#
!Pin name
!Function
!Notes
|-
|1 ||SD2_DAT3||| DATA[3] || -
|-
|2 ||SD2_CMD||| CMD line || -
|-
|3, 6 ||DGND||| Ground || -
|-
|4 ||3.3V||| Power Supply || -
|-
|5 ||SD2_CLK||| Clock || -
|-
|7 ||SD2_DAT0||| DATA[0] || -
|8 ||SD2_DAT1||| DATA[1] || -
|-
|13 9 ||GPIO_0SD2_DAT2|| - | DATA[2] ||Pull up to 3.3V with 10K Ohm -
|-
|}
=== Pin strip connectors === ==== JSPI PMOD -PROG-MICRO1 =JP17 ===
J-PROG-MICRO1 JP17 is a 3x212-pin, 26x2x2.54mm 54 pitch vertical header, pinstrip connector. The following table reports the pinout of the connector's pinout:
{| class="wikitable"
!Notes
|-
|1 || BKGD_JM60SD2_DATA1||| - || -|-|2 ||GPIO_17 ||| - || -|-|3 ||SD2_CMD ||| - || - |-|4, 6, 8 ||N.C.||| Not connected || -
|-
|2 5 || DGNDSD2_DATA0 ||| Ground || -
|-
|3, 5 7 || N.C. SD2_CLK ||| - || -
|-
|4 9, 10 || RST_JM60DGND || - | Ground || -
|-
|6 11, 12 || VIN_USB+3.3V ||| - || -
|-
|}
 
=== Pin strip connectors ===
==== J-PROG-PMIC1 ====
|1 || 2V8-4V5|| - || -
|-
|2 || MIC_PROG_GATE_CTRlPMIC_PROG_GATE_CTRl|| - || -
|-
|3 || DGND|| Ground || -
!Notes
|-
|1 || - || - || Connetted Connected to pin 3
|-
|2 || DGND|| Ground|| -
|-
|3 || - || - || Connetted Connected to pin 1
|-
|4, 6, 8, 10,<br>12, 14, 16 || NVCC_CSI_EXT|| - || -
!Notes
|-
|1 || - || - || Connetted Connected to pin 3
|-
|2 || DGND|| Ground|| -
|-
|3 || - || - || Connetted Connected to pin 1
|-
|4, 6, 8, 10,<br>12, 14, 16 || NVCC_EIM_EXT|| - || -
|}
==== MIPI CSI - JP7 ====
 
JP7 is a 8x2-pin 2.54mm pitch header pinstrip connector. The following table reports the connector's pinout:
 
{| class="wikitable"
|-
!Pin#
!Pin name
!Function
!Notes
|-
|1 || CSI_D3P || Data3 + ||
|-
|2, 5, 8, 11,<br> 14, 16 || DGND|| Ground|| -
|-
|3 || CSI_D3N || Data3- ||
|-
|4 || CSI_D2P|| Data2+ || -
|-
|6 || CSI_D2M|| Data2-|| -
|-
|7 || CSI_D1P|| Data1+|| -
|-
|9 || CSI_D1M|| Data1- || -
|-
|13 || CSI_CLK0P|| Clock+ || -
|-
|15 || CSI_CLK0M|| Clock- || -
|-
|}
==== EXPANSION CONNECTOR - JP8 ====
|}
==== MIPI DSI - JP11 ==Boot configurations ==
JP11 is a 8x2-pin 2.54mm pitch header pinstrip connector. The following table reports the connector's pinout:=== uSD ===
{| class="wikitable" |Dip-switch configuration:!Pin# !Pin name<pre>!FunctionS5[1..8] : On Off On On On On Off OffS6[1..8] : Off Off On On Off On On On!NotesS7[1..8] : Off Off On On On On On On |-S8[1..8] : On Off On On Off On On On|S9[1, ..2, 7, 8,] : Off Off<br/pre> 12, 13, 15, 16 || DGND || Ground || |-|3 || DSI_D1M || Data1 === NOR SPI=== Dip- || switch configuration:|-|4 || DSI_CLOCK0M || Clock - ||<pre>|-S5[1..8] : On On Off Off On On Off Off |5 || DSI_D1P || Data1 + ||S6[1..8] : Off Off On On Off On On On|-S7[1..8] : Off Off On Off Off Off On Off|6 || DSI_CLOCK0P S8[1..8] : On || Clock + ||Off On On Off On On OnS9[1..2] : Off Off</pre>  == XELK 2.0.0 == |===Schematics===* ORCAD: http://mirror.dave.eu/axel/AxelEVB/XELK-2.0.0/axelevb-lite-0.9.4-XELK-dsn.zip|* PDF: http://mirror.dave.eu/axel/AxelEVB/XELK-2.0.0/axelevb-lite-S.EVBA1000C0R.0.9 || DSI_DOP|| Data0 + ||.4.pdf ===BOM===|* AxelEVB-|10 || NVCC_AXEL_ILite: http://O_3mirror.3Vdave.eu/axel/AxelEVB/1XELK-2.0.8|| 0/axelevb- ||lite_BOM_S.EVBA1000C0R_0.9.4.CSV_.zip ===Layout===|* http://mirror.dave.eu/axel/AxelEVB/XELK-2.0.0/axelevb-lite_CS151613_assem_view.pdf|11 || DSI_D0M|| Data0 - |||-===Mechanical===|14 || SW4_xV* DXF: http://1mirror.dave.8V || eu/axel/AxelEVB/XELK- |||2.0.0/axelevb-|}lite_3D_CS151613.zip
==SchematicsXELK 2.2.0 ==
===Schematics===* ORCAD: http://wwwmirror.dave.eu/systemaxel/filesAxelEVB/areaXELK-riservata2.2.0/axelevb-litelite_S-EVBA1000C1R_1.0.98.3-XELK-dsndsn_.zip* PDF: http://wwwmirror.dave.eu/systemaxel/filesAxelEVB/areaXELK-riservata2.2.0/axelevb-litelite_S-SEVBA1000C1R_1.EVBA1000C0R-0.9.38.pdf
===BOM===* AxelEVB-Lite: http://wwwmirror.dave.eu/systemaxel/filesAxelEVB/areaXELK-riservata2.2.0/axelevbAXELEVB-lite_BOM_SLITE_S.EVBA1000C0R_0EVBA1000C1R.91.30.CSV_8.zip
===Layout===* http://wwwmirror.dave.eu/systemaxel/filesAxelEVB/areaXELK-riservata2.2.0/axelevb-lite_CS151613_assem_viewlite_S-EVBA1000C1R_CS151613A_AssemView.pdf
===Mechanical===* DXF: http://wwwmirror.dave.eu/systemaxel/filesAxelEVB/areaXELK-riservata2.2.0/axelevb-lite_2D_CS151613lite-S-EVBA1000C1R_CS151613A-2D.dxf_.zip* IDF (3D): http://wwwmirror.dave.eu/systemaxel/filesAxelEVB/areaXELK-riservata2.2.0/axelevb-lite_3D_CS151613lite-S-EVBA1000C1R_CS151613A-3D.idf_.zip
U0007
Bureaucrats, dave_user, Administrators
8,183
edits
Retrieved from "https://wiki.dave.eu/index.php/Special:MobileDiff/3399...8859"

Navigation menu