{{WarningMessage|text=By default, BoraXEVB comes with a Zynq 7030-based SoM when it is sold with BoraX. When it is sold with Bora Lite, it is mated with a Zynq 7020-based SoM instead.
Nevertheless, BoarX can host different models of BoraX and Bora Lite SoM's. From the point of view of PL's I/O voltage levels, different models may not be equivalent. Please refer to [[#PL's I/O voltage selections|this section]] to avoid unsupported configurations that '''may damage the hardware permanently'''.}}
==Introduction==
BORA Xpress EVB is a carrier board designed to host [[BORA_Xpress_SOM|BORA Xpress system-on-module]].
The EVB is used also as Evaluation board for the [[:Category:BoraLite | BORA Lite SOM]].
[[File:BoraXEVB-01.png|500px|frameless|border]]
<section begin==Introduction==Bora Xpress EVB is a carrier board designed to host [[BoraXpress SOM|Bora Xpress system-on-module]].Block Diagram/>
==Block Diagram==
The following picture shows Bora BORA Xpress EVB block diagram:
[[File:Boralite-boraxevb-FPGA-signals-routing.png|center|thumb|862x862px|Configurable routing options diagram for BoraLite SoM]]
<section end=Block Diagram/>
== Features ==
| LCD_BKLT_PWM I/O voltage
| LCD_BKLT_PWM signal is derived from IO_0_13 on BANK13. In the case of LVDS signals for LCD the BANK 13 must be powered at 2.5V. So in this case LCD_BKLT_PWM is an LVCMOS 2.5V signal. It is recommended to place a voltage level translator to 3.3V if the signal voltages are not compatible with the LCD diplay backlight input.
|-
| FMC connector
| For the [[Product_serial_number|serial numbers]] included in the range EVBBX0000C0R00A0 - EVBBX0000C0R00AB, the connector that is actually mounted on the board is the LPC version, not the HPC version listed in the specifications.
|-
|}
== Connectors pinout ==
<section begin=CPU/>
=== J1,J2 and J3 ===
The pinout of the J1, J2 and J3 connectors of the Bora Xpress EVB is the same of the [[Pinout (BORAXpress)BORA_Xpress_SOM/BORA_Xpress_Hardware/Pinout_Table#Connectors_description|counterpart connectors on BORA Xpress module]].<section end=CPU/><section begin=Power Supply/>
=== Power supply - JP2 ===
|-
|}
<section end=Power Supply/>
<section begin=Reset button/>
=== Reset button - S6 ===
S6 is the hardware reset button connected to the MRSTn signal (J2.16 SOM connector)
<section end=Reset button/>
<section begin=Boot Configurations/>
=== Boot mode selection - S5 ===
| SD-card || OFF || ON || OFF || ON || ON || OFF || ON || OFF
|-
| NAND (*) || OFF || ON || OFF || ON || ON || OFF || ON || ON
|-
| JTAG || OFF || ON || OFF || ON || ON || ON || ON || ON
|}
<b>(*)</b> Boot mode from NAND in supported '''ONLY''' on [[BORA Lite SOM|BORA Lite]] SOM module
<section end=Boot Configurations/>
<section begin=Watchdog/>
=== WatchDog Settings - S1, S2 and S3 ===
S1, S2 and S3 are dip-switch to override the default startup delay and timeout of the Bora BORA Xpress module watchdog.For more details please refer to [[BORA_Xpress_SOM/BORA_Xpress_Hardware/Peripherals/Watchdog (BORAXpress)|this page]].
<section begin=JTAG/>== BANK13 VDDIO selector - JP25 = JTAG ===JP25 JTAG port is a 12available as two different mechanical connectors:* 2.00mm-pin 6x2x2pitch 7x2 header (Xilinx standard)* 2.54 54mm-pitch vertical 10x2 header used for the selection - through jumpers - of the bank supply voltages(ARM standard): http://www2.lauterbach.com/pdf/arm_app_jtag.pdf* This port is connected to Zynq's native JTAG signals. Please note that Zynq's internal JTAG chain supports differents configurations, depending on bootstrap signals. In case split mode is selected, CPU JTAG can be routed separately via PL. For more details please refer to Zynq Technical Reference Manual. The following table reports the pinout of * JTAG on BORA Xpress EVB is also connected to the FMC connector:. For more details on how to connect JTAG on a custom FMC card please refer to ANSI/VITA FPGA Mezzanine Card (FMC) Standard. ==== JTAG XILINX - J13 ====
J13 is a 14-pin 7x2x2 pitch vertical header. The following table reports the pinout of the connector:
|6 || LDO_B13_400mVJTAG_TCK|| adds +400mV to VDDIO_BANK13 - || -
|-
|8 || LDO_B13_200mVJTAG_TDO|| adds +200mV to VDDIO_BANK13 - || -
|-
|10 || LDO_B13_100mVJTAG_TDI|| adds +100mV to VDDIO_BANK13 - || -
|-
|12 || LDO_B13_50mVN.C.|| adds +50mV to VDDIO_BANK13 - || -
|-
|1, 3, 5, 7, 9, 11 14 || DGNDJTAG_TRSTn|| - || -
|-
|}
The jumper configurations are:# No jumpers installed -> DC output for VDDIO_BANK13 is 500mV# Jumper on 1-2 -> adds 1.6V to VDDIO_BANK13 above the default 500mV# Jumper on 3-4 -> adds 800mV to VDDIO_BANK13 above the default 500mV# Jumper on 5-6 -> adds 400mV to VDDIO_BANK13 above the default 500mV# Jumper on 7-8 -> adds 200mV to VDDIO_BANK13 above the default 500mV# Jumper on 9-10 -> adds 100mV to VDDIO_BANK13 above the default 500mV# Jumper on 11-12 -> adds 50mV to VDDIO_BANK13 above the default 500mVThe DEFAULT configuration is VDDIO_BANK13 @ 1.8V (500mV + 800mV + 400mV + 100mV):# Jumper on 3-4 -> adds 800mV to VDDIO_BANK13 above the default 500mV# Jumper on 5-6 -> adds 400mV to VDDIO_BANK13# Jumper on 9-10 -> adds 100mV to VDDIO_BANK13 === BANK35 VDDIO selector = JTAG ARM - JP27 J18 ====JP27 J18 is a 1220-pin 6x2x210x2x2.54 pitch vertical header used for the selection - through jumpers - of the bank supply voltages. The following table reports the pinout of the connector:
The jumper configurations are:# No jumpers installed -> DC output for VDDIO_BANK35 J17 is 500mV# Jumper on 1-2 -> adds 1.6V to VDDIO_BANK35 above a standard DB9 connector that routes the default 500mV# Jumper on 3-4 -> adds 800mV to VDDIO_BANK35 above signals coming from the default 500mV# Jumper on 5-6 -> adds 400mV to VDDIO_BANK35 above the default 500mV# Jumper on 7-8 -> adds 200mV to VDDIO_BANK35 above the default 500mV# Jumper on 9-10 -> adds 100mV to VDDIO_BANK35 above the default 500mV# Jumper on 11-12 -> adds 50mV to VDDIO_BANK35 above the default 500mVThe DEFAULT configuration RS232 transceiver that is VDDIO_BANK35 @ 1.8V (500mV + 800mV + 400mV + 100mV):# Jumper on 3-4 -> adds 800mV to VDDIO_BANK35 above the default 500mV# Jumper on 5-6 -> adds 400mV connected to VDDIO_BANK35# Jumper on 9-10 -> adds 100mV to VDDIO_BANK35Please note that:* By default VDDIO_BANK35 is supplied by VADJ Regulator=== VADJ VDDIO selector - JP28 ===JP28 is a 12-pin 6x2x2.54 pitch vertical header used for the selection - through jumpers - PS MIO signals of the bank supply voltagesUART1 port. The following table reports the pinout of the connector:
The jumper configurations are:# Jumper on 1-2 -> supply VADJ with 3.3V# Jumper on 3-4 -> supply VADJ with 2.5V# Jumper on 5-6 -<section begin=USB OTG/> supply VADJ with 1.8V# Jumper on 7=== USB OTG -8 -> supply VADJ with 1.5V# Jumper on 9-10 -> supply VADJ with 1.2VThe DEFAULT configuration is:# Jumper on 5-6 -> supply VADJ with 1.8VJ19 ===
=== JTAG ===J19 is a standard USB MICRO AB connector. It is connected to the BORA Xpress USB 2.0 OTG peripheral. The following table reports the pinout of the connector:
JTAG port is available as two different mechanical connectors:
* This port is connected to Zynq's native JTAG signals. Please note that Zynq's internal JTAG chain supports differents configurations, depending on bootstrap signals. In case split mode is selected, CPU JTAG can be routed separately via PL. For more details please refer to Zynq Technical Reference Manual.
* JTAG on Bora Xpress EVB is also connected to the FMC connector. For more details on how to connect JTAG on a custom FMC card please refer to ANSI/VITA FPGA Mezzanine Card (FMC) Standard.
==== JTAG XILINX - J13 ====
J13 is a 14-pin 7x2x2 pitch vertical header. The following table reports the pinout of the connector:
J21 is a microSD memory card connector. It is connected to the BORA Xpress SOM through a bidirectional 1.8V/3.3V voltage-level translator mounted on the BORA Xpress EVB. Level shifter is required because MIO signals are 1.8V. The following table reports the pinout of the connector:
==== JTAG ARM - J18 ====
J18 is a 20-pin 10x2x2.54 pitch vertical header. The following table reports the pinout of the connector:
|15 13 |3.3V| JTAG_TRSTn|| - || ||Pull up to 3.3V with 10K Ohm -
|-
|}
<section end=micro SD/>
<section begin=DWM/>=== UART1 DWM (DAVE Wifi/BT module) socket - J17 J23 === J17 J23 is a standard DB9 52991-0308 connector that routes type (30 pins, vertical, 0.50mm picth). This socket connects the signals coming from [[DWM_ADD-ON | DWM Wireless Module]] (optional) to the RS232 transceiver that is connected to BORA Xpress EVB. The following table reports the PS MIO signals pinout of the UART1 port.connector:
J19 === CAN - J24 ===J24 is a standard USB MICRO AB connector10-pin 5x2x2. It is 54mm pitch vertical header directly connected to BORA Xpress SoM's transceiver for the Bora Xpress USB CAN interface. This 2.0 OTG peripheral5mm-pitch header is compatible with commonly available IDC-10/DB9 flat cables. The following table reports the pinout of the connector:
<section end=CAN/><section begin=Touchscreen/>=== MicroSD Touch screen - J21 J25=== J21 J25 is a microSD memory card ZIF 4-pin 1.0mm pitch connector. It is connected that connects the touchscreen drive lines to the Bora Xpress SOM through a bidirectional 1.8V/3.3V voltage-level translator mounted touch screen controller on the Bora BoORA Xpress EVB. Level shifter is required because MIO signals are 1.8V. The following table reports the pinout of the connector:
{| class="wikitable"
!Notes
|-
|1 ||PS_SD0_DAT2|TSC_YP || - || -
|-
|2 ||PS_SD0_DAT3|TSC_XP || - || -
|-
|3 ||PS_SD0_CMD|TSC_YM || - || -
|-
|4 ||3.3V|TSC_XM || - || -
|-
|5 ||PS_SD0_CLK||| }<section end=Touchscreen/><section begin=LVDS/>=== LVDS - J26 ===J26 is a vertical double row straight 20-pin 1.25mm pitch header. This interface shows how to implement a differential connection to an LCD screen. As known, Zynq does not implement an LCD controller, however this can be integrated in FPGA fabric as shown by this example: https://wiki.analog.com/resources/tools-software/linux- drivers/platforms/zynq. The following table reports the pinout of the connector: {|| -class="wikitable"
|-
|6, 9, 10, 11, 12 ||DGND||| - || -|-|7 ||PS_SD0_DAT0||| - || -|-|8 ||PS_SD0_DAT1||| - || -|-|13 |3.3V||| - || ||Pull up to 3.3V with 10K Ohm -|-|}=== DWM (DAVE Wifi/BT module) socket - J23 ===J23 is a 52991-0308 connector type (30 pins, vertical, 0.50mm picth). This socket connects the [[Wireless_Module_(DWM) | DWM Wireless Module]] (optional) to the Bora Xpress EVB. The following table reports the pinout of the connector:{| class="wikitable" |-!Pin#
J27 is a 400 pins ANSI/VITA 57.1-2008 FPGA Mezzanine Card Connector that allows to connect to standard I/O mezzanine cards.
Please note that BoraXpress EVB FMC Connector is:
* fully compliant to FMC LPC
* partially compliant to FMC HPC because HPC side is not fully populated.
=== CAN The following tables detail how BORA Xpress signals have been routed to FMC connector. At this [[:File:BoraXEVB- J24 ===J24 is a 10FMC-pin 5x2x2routing.54mm pitch vertical header directly connected to Bora Xpress SoM's transceiver zip|link]] a spreadsheet providing the same information is available for the CAN interfacedownload. This 2.5mm For more information about I/O voltage of single-pitch header is compatible with commonly ended signals available IDC-10on FMC connector, please refer to [[#PL's I/DB9 flat cablesO voltage selections|this section]]. The following table reports the pinout of the connector: ==== HPC Row A ====
|}=== Touch screen - J25===J25 is a ZIF 4-pin 1.0mm pitch connector that connects the touchscreen drive lines to the touch screen controller on the Bora Xpress EVB. The following table reports the pinout of the connector:{A5||DGND||GND|| class="wikitable"
|}=== LVDS - J26 ===J26 is a vertical double row straight 20-pin 1.25mm pitch header. This interface shows how to implement a differential connection to an LCD screen. As known, Zynq does not implement an LCD controller, however this can be integrated in FPGA fabric as shown by this example: https://wiki.analog.com/resources/tools-software/linux-drivers/platforms/zynq. The following table reports the pinout of the connector:{A11||MGTxRXN3||DP3_M2C_N|| class="wikitable"
|}=== FPGA Mezzanine Card (FMC) Connector - J27 ===J27 is a 400 pins ANSI/VITA 57.1-2008 FPGA Mezzanine Card Connector that allows to connect to standard I/O mezzanine cards.Please note that BoraXpress EVB FMC Connector is:* fully compliant to FMC LPC* partially compliant to FMC HPC because HPC side is not fully populated.==== HPC Row A ===={A27||MGTxTXN2||DP2_C2M_N|| class="wikitable"
| K10||IO_L21P_T3_DQS_AD14P_35||HA06_P|} ==== Voltage Monitor - JP15 ==== JP15 is a 16-pin 8x2x2.54 pitch vertical header. The following table reports the pinout of the connector: {|class="wikitable"
| K27||DGND||GND|} ==== Ethernet GPIO - JP18 ====JP18 is a 16-pin 8x2x2.54 pitch vertical header. The following table reports the pinout of the connector: {|class="wikitable"
=== Pin strip connectors === ==== SPI,NAND - JP13 JP19 ==== JP13 JP19 is a 12-pin 6x2x2.54 pitch vertical header. The following table reports the pinout of the connector:
<section begin=RTC/><section end=PinStrip/>== Voltage Monitor == FPGA, WatchDog, RTC, RST - JP15 JP22 ==== JP15 JP22 is a 16-pin 8x2x2.54 pitch vertical header. The following table reports the pinout of the connector:
==== Ethernet GPIO AUX PINs - JP18 JP29 ====JP18 JP29 is a 16-pin 8x2x2.54 pitch vertical header. The following table reports the pinout of the connector:
* Three devices are connected to I2C0 bus (this is level shifted from 1.8V to 3.3V):
** Silicon Labs Si571 programmable clock generator: this clock si connected to PL to allow the user to easily experiment his/her own peripherals and IPs on FPGA
** resistive touch screen controller for LCD screen
** consumption monitor: this is connected to shunt resistor put in series on BORA power rail, allowing to measure SoM consumption
==== ADC - JP30, JP31, JP32 ====
==== SPIJP30,NAND - JP19 ====JP19 is a 12JP31, JP32 are 16-pin 6x2x28x2x2.54 pitch vertical header. The following table tables reports the pinout of the connectorconnectors:
Please note that: * Three devices are connected Digilent Pmod™ Interface Specification - defined by Digilent Inc. - allows to I2C0 bus (this is level shifted from 1.8V quickly connect several pre-built I/O modules to 3.3V)PL:** Silicon Labs Si571 programmable clock generatorhttp: this clock si connected to PL to allow the user to easily experiment his/her own peripherals and IPs on FPGA/www.digilentinc.com/Products/Catalog.cfm?NavPath=2,401&Cat=9&CFID=3145471&CFTOKEN=69407812** resistive touch screen controller for LCD screenhttp://www.maximintegrated.com/products/evkits/fpga-modules/** consumption monitor: this is connected Signals used to shunt resistor put in series on Bora power rail, allowing implement LVDS LCD interface can alternatively routed to measure SoM consumptionDigilent Pmod™ Compatible compatible connector
JP31==== Digilent Pmod™ Compatible - JP23 ====JP23 is a 12-pin 6x2x2.54 pitch vertical header. The following table reports the pinout of the connector:
{| class="wikitable"
|-
!Notes
|-
|1 || FPGA_BANK35_AD5N PMOD_B0 || AD5_N - || Mount option-
|6 style="text-align: center;" |7014S/7020(CLG400 package)| FPGA_BANK35_AD12P style="text-align: center;" |HR(1.2 - 3.3V)| AD12_P style="text-align: center;" |User defined| Mount style="text-align: center;" | HR(1.2 - 3.3V)| style="text-align: center;" | User defined| style="text-align: center;" | HR(1.2 - 3.3V)| style="text-align: center;" | User defined|}[1]*HR = High Range*HP = High Performance ===BoraXEVB voltage selection jumpers===BoraXEVB provides several configuration jumpers that allow to easily select the voltages used for PL's I/O banks. The following tables lists some of the allowed combinations used to select the most common voltage values. There are other combination available. However, '''some of them are not allowed and may cause permanent hardware damages to the Zynq part'''. Since characteristics of PL's I/O banks differ between Zynq 7015 and 7030 parts, the valid combinations '''are not the same for all of the BoraX models'''. Please refer to the following sections for more details. Even if PL's banks are independent, default configuration of BoraXEVB is such that*bank 34 and bank 35 have the same supply voltage*this voltage is selected via JP28.This configuration is in accordance with default routing of signals used for FMC connector.====Examples of valid combinations for Zynq 7030-based SOMs (default optionfor BXELK)===={| class="wikitable" style="text-align: center;"|+Bank #13 (HR)
=== Digilent Pmod™ Compatible headers ===Please note that: * Digilent Pmod™ Interface Specification - defined by Digilent Inc. - allows to quickly connect several pre-built I/O modules to PL:** http://www.digilentinc.com/Products/Catalog.cfm?NavPath=2,401&Cat=9&CFID=3145471&CFTOKEN=69407812** http://www.maximintegrated.com/products/evkits/fpga-modules/* Signals used to implement LVDS LCD interface can alternatively routed to Digilent Pmod™ Compatible compatible connector ==== Digilent Pmod™ Compatible - JP17 ====JP17 is a 12-pin 6x2x2.54 pitch vertical header. The following table reports the pinout of the connector: {| class="wikitable" style="text-align: center;"|+Bank #34 (HP)
====Advanced information about voltage selection connectors====
===== Bank 13 VDDIO selection connector (JP25) =====
JP25 is a 12-pin 6x2x2.54 pitch vertical header used for the selection - through jumpers - of the bank supply voltages. The following table reports the pinout of the connector:
==== Digilent Pmod™ Compatible - JP23 ====
JP23 is a 12-pin 6x2x2.54 pitch vertical header. The following table reports the pinout of the connector:
|} The jumper configurations are:# No jumpers installed -> DC output for VDDIO_BANK13 is 500mV# Jumper on 1-2 -> adds 1.6V to VDDIO_BANK13 above the default 500mV# Jumper on 3-4 -> adds 800mV to VDDIO_BANK13 above the default 500mV# Jumper on 5-6 -> adds 400mV to VDDIO_BANK13 above the default 500mV# Jumper on 7-8 ||PMOD_B7 || - > adds 200mV to VDDIO_BANK13 above the default 500mV# Jumper on 9-10 -> adds 100mV to VDDIO_BANK13 above the default 500mV# Jumper on 11-12 -> adds 50mV to VDDIO_BANK13 above the default 500mV The default configuration is VDDIO_BANK13 @ 1.8V (500mV + 800mV + 400mV + 100mV):# Jumper on 3-4 -> adds 800mV to VDDIO_BANK13 above the default 500mV# Jumper on 5-6 -> adds 400mV to VDDIO_BANK13# Jumper on 9-10 -> adds 100mV to VDDIO_BANK13 ===== Bank 35 VDDIO selection connector (JP27) =====JP27 is a 12-pin 6x2x2.54 pitch vertical header used for the selection - through jumpers - of the bank supply voltages. The following table reports the pinout of the connector: {|| -class="wikitable"
|11, 2 || LDO_B35_1V6|| adds +1.6V to VDDIO_BANK35 || -|-|4 || LDO_B35_800mV|| adds +800mV to VDDIO_BANK35 || -|-|6 || LDO_B35_400mV|| adds +400mV to VDDIO_BANK35 || -|-|8 || LDO_B35_200mV|| adds +200mV to VDDIO_BANK35 || -|-|10 || LDO_B35_100mV|| adds +100mV to VDDIO_BANK35 || -|-|12 ||LDO_B35_50mV|| adds +50mV to VDDIO_BANK35 || -|-|1, 3.3V , 5, 7, 9, 11 || DGND|| - || -
|-
|}
The jumper configurations are:
# No jumpers installed -> DC output for VDDIO_BANK35 is 500mV
# Jumper on 1-2 -> adds 1.6V to VDDIO_BANK35 above the default 500mV
# Jumper on 3-4 -> adds 800mV to VDDIO_BANK35 above the default 500mV
# Jumper on 5-6 -> adds 400mV to VDDIO_BANK35 above the default 500mV
# Jumper on 7-8 -> adds 200mV to VDDIO_BANK35 above the default 500mV
# Jumper on 9-10 -> adds 100mV to VDDIO_BANK35 above the default 500mV
# Jumper on 11-12 -> adds 50mV to VDDIO_BANK35 above the default 500mV
The DEFAULT configuration is VDDIO_BANK35 @ 1.8V (500mV + 800mV + 400mV + 100mV):
# Jumper on 3-4 -> adds 800mV to VDDIO_BANK35 above the default 500mV
# Jumper on 5-6 -> adds 400mV to VDDIO_BANK35
# Jumper on 9-10 -> adds 100mV to VDDIO_BANK35
{{ImportantMessage|text=Please note that by default VDDIO_BANK35 is supplied by VADJ Regulator. For using a dedicated VDDIO_BANK35, it is required to remove R343 and mount R344: check BORA Xpress Evaluation Kit schematics page 10.<br>
Then, check and/or properly configure JP27 for selecting the required VDDIO_BANK35}}
===== Bank 34 and VADJ VDDIO selection connector (JP28) =====
JP28 is a 12-pin 6x2x2.54 pitch vertical header used for the selection - through jumpers - of the bank supply voltages. The following table reports the pinout of the connector:
{| class="wikitable"
|-
!Pin#
!Pin name
!Function
!Notes
|-
|2 || VADJ_FB (22K)|| selects 3.3V VADJ || -
|-
|4 || VADJ_FB (30K9)|| selects 2.5V VADJ || -
|-
|6 || VADJ_FB (51K1)|| selects 1.8V VADJ || -
|-
|8 || VADJ_FB (68K)|| selects 1.5V VADJ || -
|-
|10 || VADJ_FB (100K)|| selects 1.2V VADJ || -
|-
|12 || RFU|| Reserved || -
|-
|1, 3, 5, 7, 9, 11 || DGND|| - || -
|-
|}
The jumper configurations are:
# Jumper on 1-2 -> supply VADJ with 3.3V
# Jumper on 3-4 -> supply VADJ with 2.5V
# Jumper on 5-6 -> supply VADJ with 1.8V
# Jumper on 7-8 -> supply VADJ with 1.5V
# Jumper on 9-10 -> supply VADJ with 1.2V
The default configuration is:
# Jumper on 5-6 -> supply VADJ with 1.8V
<section end=Voltage selections/>
<section begin=SOM/>
==SoM's signals mapping==
===Bora Lite===
As known, Bora Lite requires an [[BoraLite_Adapter_for_the_BoraXEVB_carrier_board|adapter]] to be mounted on the BoraXEVB carrier board. The adapter swap some signals to allow to use some carrier board peripherals routed on unavailable pins of the SoM. For this reason, it can be tricky to find out where the SoM's signals are routed at the carrier board level. The following table details such routing for PL banks. Here '''it is assumed to use an adapter with default mounting options'''.
{| class="wikitable"
|+
! colspan="2" |SoM's signal
! colspan="6" |Routing options at carrier board level
|-
! rowspan="2" |Bank
! rowspan="2" |Name
! colspan="3" |Option #1
(default)
! colspan="3" |Option #2
|-
!Name
!Pin
!Note
!Name
!Pin
!Note
|-
| rowspan="54" |34
| rowspan="2" |IO_0_34
| rowspan="2" |'''IO_0_VRN_34'''
|J31.2
|Header
| rowspan="2" |
| rowspan="2" |
| rowspan="2" |
|-
|J27D.H2
|FMC conn.
|-
| rowspan="2" |IO_25_34
| rowspan="2" |'''IO_25_VRP_35'''
|J31.4
|Header
| rowspan="2" |
| rowspan="2" |
| rowspan="2" |
|-
|J27B.D1
|FMC conn.
|-
|IO_L10N_T1_34
|IO_L10N_T1_34
|J27D.H26
|FMC conn.
|
|
|
|-
|IO_L10P_T1_34
|IO_L10P_T1_34
|J27D.H25
|FMC conn.
|
|
|
|-
|IO_L11N_T1_SRCC_34
|IO_L11N_T1_SRCC_34
|J27D.G3
|FMC conn.
|
|
|
|-
|IO_L11P_T1_SRCC_34
|IO_L11P_T1_SRCC_34
|J27D.G2
|FMC conn.
|
|
|
|-
|IO_L12N_T1_MRCC_34
|IO_L12N_T1_MRCC_34
|J27D.H5
|FMC conn.
|
|
|
|-
|IO_L12P_T1_MRCC_34
|IO_L12P_T1_MRCC_34
|J27D.H4
|FMC conn.
|
|
|
|-
|IO_L13N_T2_MRCC_34
|'''IO_L13N_T1_MRCC_34'''
|J27D.G7
|FMC conn.
|
|
|
|-
|IO_L13P_T2_MRCC_34
|'''IO_L13P_T1_MRCC_34'''
|J27D.G6
|FMC conn.
|
|
|
|-
|IO_L14N_T2_SRCC_34
|IO_L14N_T2_SRCC_34
|J27B.D9
|FMC conn.
|
|
|
|-
|IO_L14P_T2_SRCC_34
|IO_L14P_T2_SRCC_34
|J27B.D8
|FMC conn.
|
|
|
|-
|IO_L15N_T2_DQS_34
|IO_L15N_T2_DQS_34
|J27B.D21
|FMC conn.
|
|
|
|-
|IO_L15P_T2_DQS_34
|IO_L15P_T2_DQS_34
|J27B.D20
|FMC conn.
|
|
|
|-
|IO_L16N_T2_34
|IO_L16N_T2_34
|J27B.C23
|FMC conn.
|
|
|
|-
|IO_L16P_T2_34
|IO_L16P_T2_34
|J27B.C22
|FMC conn.
|
|
|
|-
|IO_L17N_T2_34
|IO_L17N_T2_34
|J27D.G22
|FMC conn.
|
|
|
|-
|IO_L17P_T2_34
|IO_L17P_T2_34
|J27D.G21
|FMC conn.
|
|
|
|-
|IO_L18N_T2_34
|IO_L18N_T2_34
|J27D.H20
|FMC conn.
|
|
|
|-
|IO_L18P_T2_34
|IO_L18P_T2_34
|J27D.H19
|FMC conn.
|
|
|
|-
| rowspan="2" |IO_L19N_T3_VREF_34
| rowspan="2" |IO_L19N_T3_VREF_34
|J27D.G19
|FMC conn.
| rowspan="2" |
| rowspan="2" |
| rowspan="2" |
|-
|TP21
|TP SMD
|-
|IO_L19P_T3_34
|n/a
|n/a
|At the adapter level, this signal (as CAN_RX) is connected to a CAN transceiver. The CAN bus is available at J24.
|
|
|
|-
|IO_L1N_T0_34
|IO_L1N_T0_34
|J27B.C19
|FMC conn.
|
|
|
|-
|IO_L1P_T0_34
|IO_L1P_T0_34
|J27B.C18
|FMC conn.
|
|
|
|-
|IO_L20N_T3_34
|IO_L20N_T3_34
|J27B.D18
|FMC conn.
|
|
|
|-
|IO_L20P_T3_34
|IO_L20P_T3_34
|J27B.D17
|FMC conn.
|
|
|
|-
|IO_L21N_T3_DQS_34
|IO_L21N_T3_DQS_34
|J27D.H17
|FMC conn.
|
|
|
|-
|IO_L21P_T3_DQS_34
|IO_L21P_T3_DQS_34
|J27D.H16
|FMC conn.
|
|
|
|-
|IO_L22N_T3_34
|IO_L22N_T3_34
|J27D.G16
|FMC conn.
|
|
|
|-
|IO_L22P_T3_34
|IO_L22P_T3_34
|J27D.G15
|FMC conn.
|
|
|
|-
|IO_L23N_T3_34
|IO_L23N_T3_34
|J27B.C11
|FMC conn.
|
|
|
|-
|IO_L23P_T3_34
|IO_L23P_T3_34
|J27B.C10
|FMC conn.
|
|
|
|-
|IO_L24N_T3_34
|IO_L24N_T3_34
|J27D.H23
|FMC conn.
|
|
|
|-
|IO_L24P_T3_34
|IO_L24P_T3_34
|J27D.H22
|FMC conn.
|
|
|
|-
|IO_L2N_T0_34
|IO_L2N_T0_34
|J27B.C15
|FMC conn.
|
|
|
|-
|IO_L2P_T0_34
|IO_L2P_T0_34
|J27B.C14
|FMC conn.
|
|
|
|-
|IO_L3N_T0_DQS_34
|IO_L3N_T0_DQS_34
|J27D.G13
|FMC conn.
|
|
|
|-
|IO_L3P_T0_DQS_PUDC_B_34
(10K pull-up on SoM)
|IO_L3P_T0_DQS_PUDC_B_34
|J27D.G12
|FMC conn.
|
|
|
|-
|IO_L4N_T0_34
|IO_L4N_T0_34
|J27D.G10
|FMC conn.
|
|
|
|-
|IO_L4P_T0_34
|IO_L4P_T0_34
|J27D.G9
|FMC conn.
|
|
|
|-
|IO_L5N_T0_34
|IO_L5N_T0_34
|J27D.H11
|FMC conn.
|
|
|
|-
|IO_L5P_T0_34
|IO_L5P_T0_34
|J27D.H10
|FMC conn.
|
|
|
|-
| rowspan="2" |IO_L6N_T0_VREF_34
| rowspan="2" |IO_L6N_T0_VREF_34
|J27B.D15
|FMC conn.
|
|
|
|-
|TP22
|TP SMD
|
|
|
|-
|IO_L6P_T0_34
|n/a
|n/a
|At the adapter level, this signal (as CAN_TX) is connected to a CAN transceiver. The CAN bus is available at J24.
|
|
|
|-
|IO_L7N_T1_34
|IO_L7N_T1_34
|J27D.H8
|FMC conn.
|
|
|
|-
|IO_L7P_T1_34
|IO_L7P_T1_34
|J27D.H7
|FMC conn.
|
|
|
|-
|IO_L8N_T1_34
|IO_L8N_T1_34
|J27D.H14
|FMC conn.
|
|
|
|-
|IO_L8P_T1_34
|IO_L8P_T1_34
|J27D.H13
|FMC conn.
|
|
|
|-
|IO_L9N_T1_DQS_34
|IO_L9N_T1_DQS_34
|J27B.D12
|FMC conn.
|
|
|
|-
|IO_L9P_T1_DQS_34
|IO_L9P_T1_DQS_34
|J27B.D11
|FMC conn.
|
|
|
|-
|
|
|
|
|
|
|
|
|-
| rowspan="54" |35
| rowspan="2" |IO_0_35
| rowspan="2" |'''IO_0_VRN_35'''
|J27C.F1
|FMC conn.
| rowspan="2" |
| rowspan="2" |
| rowspan="2" |
|-
|J31.1
|Header
|-
| rowspan="2" |IO_25_35
| rowspan="2" |'''IO_25_VRP_35'''
|J27E.K13
|FMC conn.
| rowspan="2" |
| rowspan="2" |
| rowspan="2" |
|-
|J31.3
|Header
|-
|IO_L10N_T1_AD11N_35
|IO_L10N_T1_AD11N_35
|J27D.G34
|FMC conn.
|FPGA_BANK35_AD11N
|JP32.3
|Header
|-
|IO_L10P_T1_AD11P_35
|IO_L10P_T1_AD11P_35
|J27D.G33
|FMC conn.
|FPGA_BANK35_AD11P
|JP32.1
|Header
|-
|IO_L11N_T1_SRCC_35
|IO_L11N_T1_SRCC_35
|J27E.J3
|FMC conn.
|
|
|
|-
|IO_L11P_T1_SRCC_35
|IO_L11P_T1_SRCC_35
|J27E.J2
|FMC conn.
|
|
|
|-
|IO_L12N_T1_MRCC_35
|IO_L12N_T1_MRCC_35
|J27E.K5
|FMC conn.
|
|
|
|-
|IO_L12P_T1_MRCC_35
|IO_L12P_T1_MRCC_35
|J27E.K4
|FMC conn.
|
|
|
|-
|IO_L13N_T2_MRCC_35
|IO_L13N_T2_MRCC_35
|J27C.F5
|FMC conn.
|
|
|
|-
|IO_L13P_T2_MRCC_35
|IO_L13P_T2_MRCC_35
|J27C.F4
|FMC conn.
|
|
|
|-
|IO_L14N_T2_AD4N_SRCC_35
|IO_L14N_T2_AD4N_SRCC_35
|J27C.E3
|FMC conn.
|FPGA_BANK35_AD4N
|JP30.16
|Header
|-
|IO_L14P_T2_AD4P_SRCC_35
|IO_L14P_T2_AD4P_SRCC_35
|J27C.E2
|FMC conn.
|FPGA_BANK35_AD4P
|JP30.14
|Header
|-
|IO_L15N_T2_DQS_AD12N_35
|IO_L15N_T2_DQS_AD12N_35
|J27D.H38
|FMC conn.
|FPGA_BANK35_AD12N
|JP32.8
|Header
|-
|IO_L15P_T2_DQS_AD12P_35
|IO_L15P_T2_DQS_AD12P_35
|J27D.H37
|FMC conn.
|FPGA_BANK35_AD12P
|JP32.6
|Header
|-
|IO_L16N_T2_35
|IO_L16N_T2_35
|J27D.G37
|FMC conn.
|
|
|
|-
|IO_L16P_T2_35
|IO_L16P_T2_35
|J27D.G36
|FMC conn.
|
|
|
|-
|IO_L17N_T2_AD5N_35
|IO_L17N_T2_AD5N_35
|J27E.K8
|FMC conn.
|FPGA_BANK35_AD5N
|JP31.1
|Header
|-
|IO_L17P_T2_AD5P_35
|IO_L17P_T2_AD5P_35
|J27E.K7
|FMC conn.
|FPGA_BANK35_AD5P
|JP30.15
|Header
|-
|IO_L18N_T2_AD13N_35
|IO_L18N_T2_AD13N_35
|J27E.J7
|FMC conn.
|FPGA_BANK35_AD13N
|JP32.9
|Header
|-
|IO_L18P_T2_AD13P_35
|IO_L18P_T2_AD13P_35
|J27E.J6
|FMC conn.
|FPGA_BANK35_AD13P
|JP32.7
|Header
|-
| rowspan="2" |IO_L19N_T3_VREF_35
| rowspan="2" |IO_L19N_T3_VREF_35
|J27C.F8
|FMC conn.
| rowspan="2" |
| rowspan="2" |
| rowspan="2" |
|-
|TP24
|TP SMD
|-
|IO_L19P_T3_35
|IO_L19P_T3_35
|J27C.F7
|FMC conn.
|
|
|
|-
|IO_L1N_T0_AD0N_35
|IO_L1N_T0_AD0N_35
|J27D.G25
|FMC conn.
|FPGA_BANK35_AD0P
|JP30.4
|Header
|-
|IO_L1P_T0_AD0P_35
|IO_L1P_T0_AD0P_35
|J27D.G24
|FMC conn.
|FPGA_BANK35_AD0N
|JP30.2
|Header
|-
|IO_L20N_T3_AD6N_35
|IO_L20N_T3_AD6N_35
|J27C.E7
|FMC conn.
|FPGA_BANK35_AD6N
|JP31.6
|Header
|-
|IO_L20P_T3_AD6P_35
|IO_L20P_T3_AD6P_35
|J27C.E6
|FMC conn.
|FPGA_BANK35_AD6P
|JP31.4
|Header
|-
|IO_L21N_T3_DQS_AD14N_35
|IO_L21N_T3_DQS_AD14N_35
|J27E.K11
|FMC conn.
|FPGA_BANK35_AD14N
|JP32.14
|Header
|-
|IO_L21P_T3_DQS_AD14P_35
|IO_L21P_T3_DQS_AD14P_35
|J27E.K10
|FMC conn.
|FPGA_BANK35_AD14P
|JP32.12
|Header
|-
|IO_L22N_T3_AD7N_35
|IO_L22N_T3_AD7N_35
|J27E.J10
|FMC conn.
|FPGA_BANK35_AD7N
|JP31.7
|Header
|-
|IO_L22P_T3_AD7P_35
|IO_L22P_T3_AD7P_35
|J27E.J9
|FMC conn.
|FPGA_BANK35_AD7P
|JP31.5
|Header
|-
|IO_L23N_T3_35
|IO_L23N_T3_35
|J27C.F11
|FMC conn.
|
|
|
|-
|IO_L23P_T3_35
|IO_L23P_T3_35
|J27C.F10
|FMC conn.
|
|
|
|-
|IO_L24N_T3_AD15N_35
|IO_L24N_T3_AD15N_35
|J27C.E10
|FMC conn.
|FPGA_BANK35_AD15N
|JP32.15
|Header
|-
|IO_L24P_T3_AD15P_35
|IO_L24P_T3_AD15P_35
|J27C.E9
|FMC conn.
|FPGA_BANK35_AD15P
|JP32.13
|Header
|-
|IO_L2N_T0_AD8N_35
|IO_L2N_T0_AD8N_35
|J27B.D24
|FMC conn.
|FPGA_BANK35_AD8N
|JP31.12
|Header
|-
|IO_L2P_T0_AD8P_35
|IO_L2P_T0_AD8P_35
|J27B.D23
|FMC conn.
|FPGA_BANK35_AD8P
|JP31.10
|Header
|-
|IO_L3N_T0_DQS_AD1N_35
|IO_L3N_T0_DQS_AD1N_35
|J27D.H29
|FMC conn.
|FPGA_BANK35_AD1N
|JP30.5
|Header
|-
|IO_L3P_T0_DQS_AD1P_35
|IO_L3P_T0_DQS_AD1P_35
|J27D.H28
|FMC conn.
|FPGA_BANK35_AD1P
|JP30.3
|Header
|-
|IO_L4N_T0_35
|IO_L4N_T0_35
|J27D.G28
|FMC conn.
|
|
|
|-
|IO_L4P_T0_35
|IO_L4P_T0_35
|J27D.G27
|FMC conn.
|
|
|
|-
|IO_L5N_T0_AD9N_35
|IO_L5N_T0_AD9N_35
|J27B.D27
|FMC conn.
|FPGA_BANK35_AD9N
|JP31.13
|Header
|-
|IO_L5P_T0_AD9P_35
|IO_L5P_T0_AD9P_35
|J27B.D26
|FMC conn.
|FPGA_BANK35_AD9P
|JP31.11
|Header
|-
| rowspan="2" |IO_L6N_T0_VREF_35
| rowspan="2" |IO_L6N_T0_VREF_35
|J27B.C27
|FMC conn.
| rowspan="2" |
| rowspan="2" |
| rowspan="2" |
|-
|TP23
|TP SMD
|-
|IO_L6P_T0_35
|IO_L6P_T0_35
|J27B.C26
|FMC conn.
|
|
|
|-
|IO_L7N_T1_AD2N_35
|IO_L7N_T1_AD2N_35
|J27D.H32
|FMC conn.
|FPGA_BANK35_AD2N
|JP30.10
|Header
|-
|IO_L7P_T1_AD2P_35
|IO_L7P_T1_AD2P_35
|J27D.H31
|FMC conn.
|FPGA_BANK35_AD2P
|JP30.8
|Header
|-
|IO_L8N_T1_AD10N_35
|IO_L8N_T1_AD10N_35
|J27D.G31
|FMC conn.
|FPGA_BANK35_AD10N
|JP32.2
|Header
|-
|IO_L8P_T1_AD10P_35
|IO_L8P_T1_AD10P_35
|J27D.G30
|FMC conn.
|FPGA_BANK35_AD10P
|JP31.16
|Header
|-
|IO_L9N_T1_DQS_AD3N_35
|IO_L9N_T1_DQS_AD3N_35
|J27D.H35
|FMC conn.
|FPGA_BANK35_AD3N
|JP30.11
|Header
|-
|IO_L9P_T1_DQS_AD3P_35
|IO_L9P_T1_DQS_AD3P_35
|J27D.H34
|FMC conn.
|FPGA_BANK35_AD3P
|JP30.9
|Header
|-
|
|
|
|
|
|
|
|
|-
| rowspan="26" |13
'''(not available on Zynq 7007S and 7010)'''
|IO_L11P_T1_SRCC_13
|'''IO_L23P_T3_13'''
|JP17.3
|PMOD [A]
|
|
|
|-
|IO_L11N_T1_SRCC_13
|'''IO_L23N_T3_13'''
|JP17.4
|PMOD [A]
|
|
|
|-
|IO_L12P_T1_MRCC_13
|'''IO_L9P_T1_DQS_13'''
|JP17.2
|PMOD [A]
|IO_L9P_T1_DQS_13
|J30.1
|ONE PIECE
|-
|IO_L12N_T1_MRCC_13
|'''IO_L9N_T1_DQS_13'''
|JP17.1
|PMOD [A]
|IO_L9N_T1_DQS_13
|J30.3
|ONE PIECE
|-
|IO_L13P_T2_MRCC_13
|'''IO_L7P_T1_13'''
|JP17.7
|PMOD [A]
|IO_L7P_T1_13
|J30.24
|ONE PIECE
|-
|IO_L13N_T2_MRCC_13
|'''IO_L7N_T1_13'''
|JP17.8
|PMOD [A]
|IO_L7N_T1_13
|J30.26
|ONE PIECE
|-
|IO_L14P_T2_SRCC_13
|'''IO_L15P_T2_DQS_13'''
|n/a
|ETH1_RXCK
|IO_L15P_T2_DQS_13
|J30.25
|ONE PIECE
|-
|IO_L14N_T2_SRCC_13
|'''IO_L15N_T2_DQS_13'''
|n/a
|ETH1_RXCTL
|IO_L15N_T2_DQS_13
|J30.27
|ONE PIECE
|-
|IO_L15P_T2_DQS_13
|'''IO_L5P_T0_13'''
|JP17.6
|PMOD [A]
|IO_L5P_T0_13
|J30.20
|ONE PIECE
|-
|IO_L15N_T2_DQS_13
|'''IO_L5N_T0_13'''
|JP17.5
|PMOD [A]
|IO_L5N_T0_13
|J30.18
|ONE PIECE
|-
|IO_L16N_T2_13
|IO_L16N_T2_13
|n/a
|ETH1_TXCTL
|IO_L16N_T2_13
|J30.31
|ONE PIECE
|-
|IO_L16P_T2_13
|IO_L16P_T2_13
|n/a
|ETH1_TXCK
|IO_L16P_T2_13
|J30.29
|ONE PIECE
|-
|IO_L17N_T2_13
|IO_L17N_T2_13
|n/a
|ETH1_RXD1
|IO_L17N_T2_13
|J30.35
|ONE PIECE
|-
|IO_L17P_T2_13
|IO_L17P_T2_13
|n/a
|ETH1_RXD0
|IO_L17P_T2_13
|J30.33
|ONE PIECE
|-
|IO_L18N_T2_13
|IO_L18N_T2_13
|n/a
|ETH1_RXD3
|IO_L18N_T2_13
|J30.39
|ONE PIECE
|-
|IO_L18P_T2_13
|IO_L18P_T2_13
|n/a
|ETH1_RXD2
|IO_L18P_T2_13
|J30.37
|ONE PIECE
|-
|IO_L19N_T3_VREF_13
|IO_L19N_T3_VREF_13
|n/a
|ETH1_TXD1
|IO_L19N_T3_VREF_13
|J30.43
|ONE PIECE
|-
|IO_L19P_T3_13
|IO_L19P_T3_13
|n/a
|ETH1_TXD0
|IO_L19P_T3_13
|J30.41
|ONE PIECE
|-
|IO_L20N_T3_13
|IO_L20N_T3_13
|n/a
|ETH1_TXD3
|IO_L20N_T3_13
|J30.47
|ONE PIECE
|-
|IO_L20P_T3_13
|IO_L20P_T3_13
|n/a
|ETH1_TXD2
|IO_L20P_T3_13
|J30.45
|ONE PIECE
|-
|IO_L21N_T3_DQS_13
|IO_L21N_T3_DQS_13
|n/a
|ETH1_MDC
|IO_L21N_T3_DQS_13
|J30.51
|ONE PIECE
|-
|IO_L21P_T3_DQS_13
|IO_L21P_T3_DQS_13
|n/a
|ETH1_MDIO
|IO_L21P_T3_DQS_13
|J30.49
|ONE PIECE
|-
|IO_L22N_T3_13
|IO_L22N_T3_13
|
|
|IO_L22N_T3_13
|J30.55
|ONE PIECE
|-
|IO_L22P_T3_13
|IO_L22P_T3_13
|n/a
|DWM_WIFI_IRQ
|IO_L22P_T3_13
|J30.53
|ONE PIECE
|-
| rowspan="2" |IO_L6N_T0_VREF_13
| rowspan="2" |IO_L6N_T0_VREF_13
|JP23.3
|PMOD [B]
| rowspan="2" |IO_L6N_T0_VREF_13
| rowspan="2" |J30.30
| rowspan="2" |ONE PIECE
|-
|n/a
|USB1_OC
|}
==== BoraXEVB unavailable signals ====
Some BoraXEVB signals are unavailable when it is mated with Bora Lite SoM. The following signals are '''not''' routed to the SoM due to the limited pin count of the SODIMM connector.
{| class="wikitable"
|+
BoraXEVB's signal that are not available when mated with Bora Lite SoM