Difference between revisions of "NaonEVB-Mid"
DevWikiAdmin (talk | contribs) (→Quick start (NELK)) |
DevWikiAdmin (talk | contribs) (→Quick start (NELK)) |
||
| Line 21: | Line 21: | ||
This section describes how to quick start NaonEVB-Mid-based system, provided that it is programmed according to NELK configuration. | This section describes how to quick start NaonEVB-Mid-based system, provided that it is programmed according to NELK configuration. | ||
| − | + | # connect the serial cable, provided with the board, to J17 | |
| − | + | # connect this cable to PC COM port through a NULL-modem cable (not provided) | |
| − | + | # start your favourite terminal software on PC; communication parameters are: | |
| − | + | #* baud rate: 115200 Bps | |
| − | + | #* data bits: 8 | |
| − | + | #* stop bits: 1 | |
| − | + | #* parity: none | |
| − | + | # (optional) to connect the system to Ethernet LAN, please plug cable on connector J11 | |
| − | + | # (optional) to connect the system to HDMI TV/LCD, please plug cable on connector J6 | |
| − | + | # connect a 12Vcc power supply to J14 | |
Once power has been applied, U-Boot bootloader will be executed and the following messages will be printed on serial console (please note that messages may vary due different U-Boot releases) | Once power has been applied, U-Boot bootloader will be executed and the following messages will be printed on serial console (please note that messages may vary due different U-Boot releases) | ||
Revision as of 16:01, 25 July 2012
| HOME | SOMs | SBCs | ToloMEO Embedded Assistant |  GET A QUOTE
|
 ONLINE HELPDESK
|
| Roadmap | IoT Services | ML/AI services | Embedded Design Services |
Info Box
|
Contents
Introduction[edit | edit source]
NaonEVB-Mid is a carrier board designed to evaluate the functionalities of Naon SOM.
The following picture shows block diagram of NaonEVB-Lite board.
The following images show top and bottom side of NaonEVB-Mid carrier board respectively. Peripherals and interfaces external to Naon SOM are highlighted.
Quick start (NELK)[edit | edit source]
This section describes how to quick start NaonEVB-Mid-based system, provided that it is programmed according to NELK configuration.
- connect the serial cable, provided with the board, to J17
- connect this cable to PC COM port through a NULL-modem cable (not provided)
- start your favourite terminal software on PC; communication parameters are:
- baud rate: 115200 Bps
- data bits: 8
- stop bits: 1
- parity: none
- (optional) to connect the system to Ethernet LAN, please plug cable on connector J11
- (optional) to connect the system to HDMI TV/LCD, please plug cable on connector J6
- connect a 12Vcc power supply to J14
Once power has been applied, U-Boot bootloader will be executed and the following messages will be printed on serial console (please note that messages may vary due different U-Boot releases)
Hardware information[edit | edit source]
Bootstrap settings[edit | edit source]
JTAG interfaces[edit | edit source]
Video interfaces[edit | edit source]
NaonEVB-Mid provides a rich set of video input/output interfaces. Please refer to this page for more details.
Schematics[edit | edit source]
|
Please note that Orcad CIS is required to get all the information about BOM variants included in .dsn files.
PDF files show the view of the default BOM variant used to manufacture the board. Components that are not populated are denoted as "Do Not Stuff". |
|
- Orcad: http://www.dave.eu/download/restricted/naon/nelk/2.0.0/hw/NAONEVB-MID-1.0.6.zip
- PDF: http://www.dave.eu/download/restricted/naon/nelk/2.0.0/hw/NaonEVB-Mid-1.0.6.pdf
Layout[edit | edit source]
http://www.dave.eu/download/restricted/naon/nelk/2.0.0/hw/NaonEVB-Mid-CS064311A.pdf
