Difference between revisions of "Enabling SPI1 and SPI3 on Linux (Naon)"
DevWikiAdmin (talk | contribs) m (→Introduction) |
DevWikiAdmin (talk | contribs) m (→Pin Mux Option) |
||
| Line 10: | Line 10: | ||
=== Pin Mux Option === | === Pin Mux Option === | ||
| − | + | SPI signals are available at different Naon pins. Please note that the NaonEVB-Mid carrier board provides the SPI1 and SPI3 signals at the J21 connector. | |
| + | |||
| + | The following configuration can be used: | ||
==== Option 1 ==== | ==== Option 1 ==== | ||
| Line 18: | Line 20: | ||
!CPU Ball | !CPU Ball | ||
|- | |- | ||
| − | | | + | |SPI1_SCLK |
| − | | | + | |J1.34 |
| − | | | + | |AC3 |
| + | |- | ||
| + | |SPI1_SCS1n | ||
| + | |J2.112 | ||
| + | |W6 | ||
| + | |- | ||
| + | |SPI1_D0 | ||
| + | |J1.37 | ||
| + | |AA6 | ||
| + | |- | ||
| + | |SPI1_D1 | ||
| + | |J1.90 | ||
| + | |AA3 | ||
|- | |- | ||
| − | | | + | |SPI3_SCLK |
| − | | | + | |J2.99 |
| − | | | + | |AC26 |
|- | |- | ||
| − | | | + | |SPI3_SCS1n |
| − | | | + | |J2.111 |
| − | | | + | |AG27 |
|- | |- | ||
| − | | | + | |SPI3_D0 |
| − | | | + | |J2.89 |
| − | | | + | |V22 |
|- | |- | ||
| − | | | + | |SPI3_D1 |
| − | | | + | |J2.87 |
| − | | | + | |AA25 |
|} | |} | ||
Revision as of 10:06, 3 September 2013
| HOME | SOMs | SBCs | ToloMEO Embedded Assistant |  GET A QUOTE
|
 ONLINE HELPDESK
|
| Roadmap | IoT Services | ML/AI services | Embedded Design Services |
Info Box
|
Contents
Introduction[edit | edit source]
This article shows how to enable the SPI1 and SPI3 (with CS1 chip select) interfaces which can be used in a standard Linux application.
Pin Mux Option[edit | edit source]
SPI signals are available at different Naon pins. Please note that the NaonEVB-Mid carrier board provides the SPI1 and SPI3 signals at the J21 connector.
The following configuration can be used:
Option 1[edit | edit source]
| Signal | Naon Connector Phisical Pin | CPU Ball |
|---|---|---|
| SPI1_SCLK | J1.34 | AC3 |
| SPI1_SCS1n | J2.112 | W6 |
| SPI1_D0 | J1.37 | AA6 |
| SPI1_D1 | J1.90 | AA3 |
| SPI3_SCLK | J2.99 | AC26 |
| SPI3_SCS1n | J2.111 | AG27 |
| SPI3_D0 | J2.89 | V22 |
| SPI3_D1 | J2.87 | AA25 |
U-Boot patches[edit | edit source]
 The patches below applies to NELK 4.0.0 and above U-Boot source tree. |
The files arch/arm/mach-omap2/board-diva.c and arch/arm/mach-omap2/diva_pinmux_table.h must be modified according to the following patches:
U-Boot must be rebuilt to make these modifications effective.
Linux kernel patches[edit | edit source]
|
The patches below applies to NELK 4.0.0 and above Linux source tree. |
The files arch/arm/mach-omap2/board-diva.c and arch/arm/mach-omap2/diva_pinmux_table.h must be modified according to the following patches:
The kernel must be rebuilt to make these modifications effective.
Using the interfaces[edit | edit source]
Users can access the peripherals connected to the SP1 and SPI3 buses through the spidev interface. For further information, please refer to
- https://www.kernel.org/doc/Documentation/spi/spidev
- https://www.kernel.org/doc/Documentation/spi/spidev_test.c
